• Journal of Technology Innovation
• /
• 제24권2호
• /
• pp.57-89
• /
• 2016

This paper used individual establishment level data to estimate the effects of government support for the research and development of 'small and medium enterprises'(SMEs). We analyzed, on the establishment level, the degree of technical advancement, strength of private R&D incentives, and the effect on employment levels of firms which participated in the 2010 government R&D support project. The results of this study are as follows. First, the size and frequency of government investment in the R&D of SMEs were both positively correlated with the amount of patent registrations. Furthermore, we found that the amount of patent registrations were positively correlated with the size of the establishments, but the average level of technological advancement for the firms running the research was lower than the average level of technological advancement for the firms merely participating in the project. Second, the government's R&D policy was found to be complementary to private R&D incentives, and a 1% increase in government R&D investment resulted in an inelastic increase (0.193~0.245%) of the firms' post-program R&D spending. Third, we found that R&D support from the government contributed to an increase of employment by the participating firms. Additionally, we found that the impact of R&D support on job creation varied for the firm size and technological characteristics. Therefore, it is important for governments to take into consideration each type of small business, when setting R&D policies.

• Journal of the Korea Concrete Institute
• /
• 제17권1호
• /
• pp.85-94
• /
• 2005

Post-tensioned Precast concrete System(PPS) consists of U-shaped precast wide beams and concrete column. The continuity of beam-column joint is provided with floor concrete cast on the PC shell beam and post-tensioning. The purpose of this paper is to evaluate the response of PPS interior beam-column joint subjected to cyclic lateral loading. To this end, an experimental investigation was performed with three half-scale specimens of interior connection. The design parameters are the amount of beam reinforcement placed inside the joint core. The test results showed that cracks were distributed well without my significant degradation of strength and ductility. Also, it was found that the prestressing may affect to alter the torsional crack angle. And the specimens sufficiently resist up to limiting drift ratio of 0.035 in accordance with the provisional by ACl of acceptance criteria for concrete special moment frames.

• Korean Journal of Poultry Science
• /
• 제6권2호
• /
• pp.91-102
• /
• 1979

The basic problem of the broiler industry is that of fluctuating prices, mainly thanks to unstable supply of and inelastic demand for products as usually indicated as a peculiarity of agricultural commodities. This particularly brings the producer to a great economic risk, because he has to sell products under the condition of pure competition, whereas others from whom he has to buy deal under the condition of oligopoly or even monopoly. Therefore, producers economic position is generally placed in the worst comparing others dealing with, which results in unbalanced economic status of elements involved in broiler operation and further obstruction of industry development as a whole. A certain type of business coordination to overcome such a problem should be measured in order to improve the efficiency of entire operation and thus assure the balanced industry development. The concept of the economic integration developed in modern business system had been adapted to U.S. poultry industry which became common later around the world as a means of stabilizing producers price and whole industry as well. There are two main typos of integration; horizontal and vertical The former refers to the general grouping of similar business units, eg. a hatchery tying with other hatchery, while the latter refers to the knitting together of two or more stages of economic activities, eg. tying together among units of hatching, fled milling, production, processing and marketing. By having the industry integrated, risk and uncertainty involved in various stages of operation could be diversified. The typo of integrating contract between producers and integrators include the share of profits, flat fee payment, feed conversion payment and salary basis. In the U.S., extensive changes in production, processing, and marketing during the last few decades have changed the thicken broiler industry from one of small, widely scattered farms to one that is largo, concentrated and efficient. More than 99 percent of all broilers produced are grown under contract and by integrated firms which vary in size of operation and complexity. About 84 percent of all production is concentrated in 10 States. Some of the other factors ;hat contributed to these choses arc costs, energy use, prices, processing, marketing and demand. No integrated broiler production system has yet been applied in Korea's poultry industry, thus all stages all broiler operation run independently seeking for its own profit. Consequently, producers price fluctuate very widely around the year even more than 50 percent in a few months. This also leads to disadvantages of material supplies, processors and distributors and enforce the industry unstable. The current economic environment in Korea seems that the time for broiler integration comes and as an ideal integrator, feed millers, food processors and producers group may be considered.

• The Korean Journal of Petroleum Geology
• /
• 제11권1호
• /
• pp.9-17
• /
• 2005

In the main target area of the block II, Targe-scale faults occur below the unconformity developed around 1 km in depth. The contrast of seismic velocity around the unconformity is generally so large that the strong multiples and the radical velocity variation would deteriorate the quality of migrated section due to serious distortion. More than 15 kinds of data processing techniques have been applied to improve the image resolution for the structures farmed from this active crustal activity. The bad and noisy traces were edited on the common shot gathers in the first step to get rid of acquisition problems which could take place from unfavorable conditions such as climatic change during data acquisition. Correction of amplitude attenuation caused from spherical divergence and inelastic attenuation has been also applied. Mild F/K filter was used to attenuate coherent noise such as guided waves and side scatters. Predictive deconvolution has been applied before stacking to remove peg-leg multiples and water reverberations. The velocity analysis process was conducted at every 2 km interval to analyze migration velocity, and it was iterated to get the high fidelity image. The strum noise caused from streamer was completely removed by applying predictive deconvolution in time space and ${\tau}-P$ domain. Residual multiples caused from thin layer or water bottom were eliminated through parabolic radon transform demultiple process. The migration using curved ray Kirchhoff-style algorithm has been applied to stack data. The velocity obtained after several iteration approach for MVA (migration velocity analysis) was used instead or DMO for the migration velocity. Using various testing methods, optimum seismic processing parameter can be obtained for structural and stratigraphic interpretation in the Block II, Yellow Sea Basin.

• Journal of Pharmaceutical Investigation
• /
• 제37권3호
• /
• pp.137-148
• /
• 2007

Using a strain-controlled rheometer [Rheometrics Dynamic Analyzer (RDA II)], the steady shear flow properties of a semi-solid ointment base (vaseline) have been measured over a wide range of shear rates at temperature range of $25{\sim}60^{\circ}C$. In this article, the steady shear flow properties (shear stress, steady shear viscosity and yield stress) were reported from the experimentally obtained data and the effects of shear rate as well as temperature on these properties were discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters (yield stress, consistency index and flow behavior index). Main findings obtained from this study can be summarized as follows : (1) At temperature range lower than $40^{\circ}C$, vaseline is regarded as a viscoplastic material having a finite magnitude of yield stress and its flow behavior beyond a yield stress shows a shear-thinning (or pseudo-plastic) feature, indicating a decrease in steady shear viscosity as an increase in shear rate. At this temperature range, the flow curve of vaseline has two inflection points and the first inflection point occurring at relatively lower shear rate corresponds to a static yield stress. The static yield stress of vaseline is decreased with increasing temperature and takes place at a lower shear rate, due to a progressive breakdown of three dimensional network structure. (2) At temperature range higher than $45^{\circ}C$, vaseline becomes a viscous liquid with no yield stress and its flow character exhibits a Newtonian behavior, demonstrating a constant steady shear viscosity regardless of an increase in shear rate. With increasing temperature, vaseline begins to show a Newtonian behavior at a lower shear rate range, indicating that the microcrystalline structure is completely destroyed due to a synergic effect of high temperature and shear deformation. (3) Over a whole range of temperatures tested, the Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have an almostly equivalent ability to quantitatively describe the steady shear flow behavior of vaseline, whereas the Bingham, Casson,and Vocadlo models do not give a good ability.

• Magazine of the Korean Society of Agricultural Engineers
• /
• 제39권4호
• /
• pp.106-113
• /
• 1997

Dynamic loading of structures often causes excursions of stresses well into the inelastic range, and the influence of the geometric changes on the dynamic response is also significant in many cases. Therefore, both material and geometric nonlinearity effects should be considered in case that a dynamic load acts on the structure. A structure in a nuclear power plant is a structure of importance which puts emphasis on safety. A nuclear container is a pressure vessel subject to internal pressure and this structure is constructed by a reinforced concrete or a pre-stressed concrete. In this study, the material nonlinearity effect on the dynamic response is formulated by the elasto-viscoplastic model highly corresponding to the real behavior of the material. Also, the geometrically nonlinear behavior is taken into account using a total Lagrangian coordinate system, and the equilibrium equation of motion is numerically solved by a central difference scheme. The constitutive relation of concrete is modeled according to a Drucker-Prager yield criterion in compression. The reinforcing bars are modeled by a smeared layer at the location of reinforcements, and the steel layer model under Von Mises yield criteria is adopted to represent an elastic-plastic behavior. To investigate the dynamic response of a nuclear reinforced concrete containment structure, the steel-ratios of 0, 3, 5 and 10 percent, are considered. The results obtained from the analysis of an example were summarized as follows 1. As the steel-ratio increases, the amplitude and the period of the vertical displacements in apex of dome decreased. The Dynamic Magnification Factor(DMF) was some larger than that of the structure without steel. However, the regular trend was not found in the values of DMF. 2. The dynamic response of the vertical displacement and the radial displacement in the dome-wall junction were shown that the period of displacement in initial step decreased with the steel-ratio increases. Especially, the effect of the steel on the dynamic response of radial displacement disapeared almost. The values of DMF were 1.94, 2.5, 2.62 and 2.66, and the values increased with the steel-ratio. 3. The characteristics of the dynamic response of radial displacement in the mid-wall were similar to that of dome-wall junction. The values of DMF were 1.91, 2.11, 2.13 and 2.18, and the values increased with the steel-ratio. 4. The amplitude and the period of the hoop-stresses in the dome, the dome-wall junction, and the mid-wall were shown the decreased trend with the steel-ratio. The values of DMF were some larger than those of the structure without steel. However, the regular trend was not found in the values of DMF.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2011년도 정기 학술발표대회
• /
• pp.155-155
• /
• 2011

일반적으로 I형 보에 횡하중이 작용하는 경우, 횡 변위와 함께 회전을 동반하는 횡-비틀림 좌굴(Lateral-Torsional Buckling)이 발생하게 된다. 이러한 I형 보의 탄성 및 비탄성 횡-비틀림 좌굴에 대한 해석적 이론적 연구는 이미 많은 연구자들에 의해 수행되었다(Timoshenko 등, 1961; Galambos, 1963; Lindner, 1974; Trahair, 1993). I형 보의 비지지 길이 내 하중이 작용할 때 모멘트 구배계수(Cb)는 하중이 부재 단면에 작용하는 위치에 따라 달라지게 되는데 이를 하중고 효과(Load Height Effects)라고 한다. 탄성 영역 내 비지지길이가 존재하는 I형 보의 하중고 효과를 고려한 모멘트 구배계수 제안식은 Nethercot & Rockey(1971)에 의해 연구된 바 있다. 또한 Helwig 등(1997)은 Nethercot & Rockey(1971)의 제안식을 간략화 하여 탄성 영역 내 비지지길이가 존재하는 I형 보의 하중고 효과를 고려한 모멘트 구배계수식을 제안하였다. 그러나 현재까지 진행 된 하중고 효과에 대한 연구는 탄성 영역 내 비지지 길이가 존재하는 I형 보에 대한 제안식이며 현재까지 비탄성 영역 내 비지지 길이를 갖는 I형 보의 하중고 효과에 대한 연구는 진행된 바 없다. 본 연구는 비탄성 영역 내 비지지 길이가 존재하는 I형 보의 하중고 효과를 고려한 비탄성 횡-비틀림 좌굴강도에 대한 연구를 수행하였다. 하중조건으로는 집중하중 과 등분포 하중을 적용시켰으며, 비선형 횡-비틀림 좌굴 해석을 위해 잔류응력 및 초기변형을 고려하였다. Pi와 Trahair(1995)이 고려한 단순직선분포를 잔류응력으로 가정하였으며, 국내 I형강 표준 치수 허용치(현대제철, 2006)에 근거하여 부재 길이의 0.1%를 초기 최대 횡 변위로 적용하여 초기제작오차로 고려하였다. 유한요소해석결과를 바탕으로 Nethercot & Rockey(1971)와 Helwig 등(1997)의 연구내용을 바탕으로 범용구조해석 프로그램(ABAQUS, 2007)을 이용하여 비탄성 영역 내 존재하는 I형보의 횡-비틀림 좌굴강도를 산정하였다. 유한요소해석결과를 바탕으로 Nethercot & Rockey(1971)및 Helwig 등(1997)의 모멘트구배계수 제안식과 비교 분석 하였고 회기분석프로그램 MINITAB(2006)을 이용하여 비탄성 영역 내 비지지길이가 존재하는 I형보의 하중고 효과를 고려한 모멘트구배계수식을 개발 제안하였다. 본 연구에서 개발된 제안식은 경제적이고 합리적인 휨부재 강도평가에 적극 활용될 수 있으며, 비탄성 영역내 I형보의 횡-비틀림 좌굴강도 및 휨강도 연구에 널리 활용될 것이다.

• Journal of Korean Society of Transportation
• /
• 제25권3호
• /
• pp.137-144
• /
• 2007

This study involves an analytical approach to determine transit dispatching schedules (headways) Determining a time schedule is an important process in transit system planning. In general, the transit headway should be shorter during the peak hour than at non-peak hours for demand-responsive service. It allows passengers to minimize their waiting time under inelastic, fixed demand conditions. The transit headway should be longer as operating costs increase, and shorter as demand and waiting time increase. Optimal headway depends on the amount of ridership. and each individual vehicle dispatching time depends on the distribution of the ridership. This study provides a theoretical foundation for the dispatching scheme consistent with common sense. Previous research suggested a dispatching scheme with even headway. However, according to this research, that is valid for a specific case when the demand pattern is uniform. This study is a general analysis expanding that previous research. This study suggests an easy method to set a time table without a complex and difficult calculation. Further. if the time axis is changed to the space axis instead, this study could be expanded to address the spacing problems of some facilities such as roads. stations, routes and others.

• Journal of the Korean Geotechnical Society
• /
• 제30권4호
• /
• pp.35-45
• /
• 2014

Limit equilibrium methods of slope stability analysis have been widely adopted mainly due to their simplicity and applicability. However, the conventional methods may not give reliable and convincing results for various geological conditions such as nonhomogeneous and anisotropic soils. Also, they do not take into account soil slope history nor the initial state of stress, for example excavation or fill placement. In contrast to the limit equilibrium analysis, the analysis of deformation and stress distribution by finite element method can deal with the complex loading sequence and the growth of inelastic zone with time. This paper proposes a technique to determine the critical slip surface as well as to calculate the factor of safety for shallow failure on partially saturated soil slope. Based on the effective stress field in finite element analysis, all stresses are estimated at each Gaussian point of elements. The search strategy for a noncircular critical slip surface along weak points is appropriate for rainfall-induced shallow slope failure. The change of unit weight by seepage force has an effect on the horizontal and vertical displacements on the soil slope. The Drucker-Prager failure criterion was adopted for stress-strain relation to calculate coupling hydraulic and mechanical behavior of the partially saturated soil slope.

• Journal of Environmental Policy
• /
• 제14권4호
• /
• pp.23-44
• /
• 2015

The policy aimed at introducing a Bonus-Malus system to reduce GHG and raise the market share of small cars is scheduled to go into effect in South Korea in 2020. Although the policy was originally planned to be enforced from 2015, the Ministry of Trade, Industry and Energy argued that the system brings low reduction effect and relative disadvantage to domestic small cars and brought arguments in 2014. As a result, the enforcement was pushed back. Related studies are mainly focused on offering statistical estimation of the policy's effect to support the arguments, and few theoretical studies were published given that there was not enough time until 2015 back then. The author approached the issue with mathematical modeling in order to give theoretical basis for sophisticated empirical studies. If car suppliers have market power and strategically set their prices, the impact of Bouns-Malus on car prices would be lower than what was originally intended. In case only a part of the car market loses its market power, the effect of the policy would be improved. Assume that the Bonus-Malus is currently at an optimal level and the car market structure is undergoing changes, then the direction of the new optimal level would depend on the elasticity of demand of each market and substitute elasticity. For example, if the car market becomes more monopolistic while the demand for big cars is elastic, demand for small cars is inelastic and substitution elasticity is low, then the new optimal level of Bonus-Malus should be higher.