• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.195-197
• /
• 1993

In this paper, a planar vibratory gyroscope is designed and fabricated in macro model. Elementary experiment and test are done for micro model. This gyroscope has a double gimbal structure with an active dimension $80{\times}120{\times}1\;mm^3$. Outer gimbal vibration is generated by electromagnetic force using ferrite E-core wounded by coil. Inner gimbal vibration is detected by inductive sensor. It is demonstrated' that mechanical and electrical symmetries are important for improvement of vibratory gyroscope.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.315-315
• /
• 2004

자기베어링 시스템은 액츄에이터, 센서, 제어기, 전류앰프 등으로 구성되어 있으며 시스템의 신뢰도는 각 구성 요소의 신뢰도와 구성요소의 상호 작용에 의해 결정된다. 자기 베어링 기술이 현재 보다 많은 분야에 적용되기 위해서는 신뢰도의 향상이 필수적이다. 본 논문에서는 자기베어링에서 사용되는 센서 중 일부가 작동하지 않더라도 시스템이 정상적으로 작동하는 센서 고장 허용 자기 베어링 시스템을 기술하였다.(중략)

• 전기의세계
• /
• v.26 no.2
• /
• pp.21-29
• /
• 1977

우리의 일상생활과 공업생산에 있어서 에너지활용의 중간형태로서 뿐아니라 information전달이나 sensor 또는 transducer signal의 검출.증폭과 제어신호수단으로서 전기가 차지하는 중요한 위치는 재언할 필요가 없다. 이러한 전기적량을 정확하게 측정하고 그 정밀도를 향상시키기 위한 연구가 세계각국의 표준연구기관에서 꾸준히 계속되고 있다. 작년가을 미국 NBS에서의 각종회의와 호주에서 열린 IMEKO Colloquium에 참석하고 관련연구기관들을 방문하는 기회에 거기에서 얻은 견문중에서 최근 활발하게 논의되고 있는 ze/h volt standard, solid state WHM, CCVT, inductive voltage divider와 전기기기의 QA절차등의 화제를 중심으로 이 두나라에서의 전기측정표준에 관한 연구현황을 소개하고저 한다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.669-676
• /
• 2013

In this study, we introduce a polymer(polyimide) based pressure sensor to measure real-time heart beat and blood pressure. The sensor have been designed with consideration of skin compatibility of material, cost effectiveness, manufacturability and wireless detection. The designed sensor was composed of inductor coils and an air-gap capacitor which generate self-resonant frequency when electrical source is applied on the system. The sensor was obtained with metalization, etching, photolithography, polymer adhesive bonding and laser cutting. The fabricated sensor was shaped in circular type with 10mm diameter and 0.45 mm thickness to fit radial artery. Resonant frequencies of the fabricated sensors were in the range of 91~96 MHz on 760 mmHg pressurized environment. Also the sensor has good linearity without any pressure-frequency hysteresis. Sensitivity of the sensor was 145.5 kHz/mmHg and accuracy was less than 2 mmHg. Real-time heart beat measurement was executed with a developed hand-held measurement system. Possibility of real-time blood pressure measurement was showed with simulated artery system. After installation of the sensor on skin above radial artery, simple real blood pressure measurement was performed with 64 mmHg blood pressure variation.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.9
• /
• pp.446-451
• /
• 2006

The output voltage value of AC high voltage source has been usually measured by employing the high voltage divider of inductive or capacitive type. In the study, we have developed a new method for measuring the output voltage up to 60kV using parallel plates electrode and electric field sensor, which are constructed by home-made. Unlikely the conventional method using a high voltage divider, this developed method makes it possible to extend the range of output voltage from known low voltage measurement to high voltage measurement. From the linearity measured between electric field and applied voltage in the output voltage range of 1kV-30kV, the output voltage value up to 60kV can be obtained by the electric field measurement using the electric field sensor. The output voltage value obtained using the method is consistent with that obtained using high voltage divider within corresponding uncertainties.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.1
• /
• pp.1-5
• /
• 2008

In this paper, we fabricated pressure difference type gas flow sensor using only dry etching technology by ICP-RIE(inductive coupled plasma reactive ion etching). The sensor's structure consists of a common shear stress type piezoresistive pressure sensor with an orifice fabricated in the middle of the sensor diaphragm. Generally, structure like diaphragm is fabricated by wet etching technology using TMAH, but we fabricated diaphragm by only dry etching using ICP-RIE. To equalize the thickness of diaphragm we applied insulator($SiO_2$) layer of SOI(Si/$SiO_2$/Si-sub) wafer as delay layer of dry etching. Size of fabricated diaphragm is $1000{\times}1000{\times}7\;{\mu}m^3$ and overall chip $3000{\times}3000{\times}7\;{\mu}m^3$. We measured the variation of output voltage toward the change of gas pressure to analyze characteristics of the fabricated sensor. Sensitivity of fabricated sensor was relatively high as about 1.5mV/V kPa at 1kPa full-scale. Nonlinearity was below 0.5%F.S. Over-pressure range of the fabricated sensor is 100kPa or more.

• ETRI Journal
• /
• v.36 no.5
• /
• pp.808-818
• /
• 2014

To deal with the major challenges of embedded sensor networks, we consider the use of magnetic fields as a means of reliably transferring both information and power to embedded sensors. We focus on a power allocation strategy for an orthogonal frequency-division multiplexing system to maximize the transferred power under the required information capacity and total available power constraints. First, we consider the case of a co-receiver, where information and power can be extracted from the same signal. In this case, we find an optimal power allocation (OPA) and provide the upper bound of achievable transferred power and capacity pairs. However, the exact calculation of the OPA is computationally complex. Thus, we propose a low-complexity power reallocation algorithm. For practical consideration, we consider the case of a separated receiver (where information and power are transferred separately through different resources) and propose two heuristic power allocation algorithms. Through simulations using the Agilent Advanced Design System and Ansoft High Frequency Structure Simulator, we validate the magnetic-inductive channel characteristic. In addition, we show the performances of the proposed algorithms by providing achievable ${\eta}$-C regions.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.760-765
• /
• 2004

One of the obstacles for a magnetic bearing to be used in the wide range of industrial applications is the failure modes associated with magnetic bearings, which we don't expect for conventional passive bearings. These failure modes include electric power outage, power amplifier faults, position sensor faults, and the malfunction of controllers. Fault-tolerant magnetic bearing systems have been proposed so that the system can operate in spite of some faults in the system. In this paper, we designed and implemented a fault-tolerant magnetic bearing system for a turbo-molecular vacuum pump. The system can cope with the actuator/amplifier faults as well as the faults in position sensors, which are the two major fault modes in a magnetic bearing system.

• Journal of Sensor Science and Technology
• /
• v.17 no.1
• /
• pp.23-28
• /
• 2008

In order to measure bio-signals, it is desirable to build a fully implantable system which connects directly to neural pathways or body tissue. A design scheme for fully implementable measurement system is proposed in this paper. Consisting of an implanted module and an external system, the proposed scheme delivers power and data between the two modules. The external module sends power via inductive link using a simple H-bridge type oscillator. Also, the implanted module sends measured data to the external system utilizing R/F communication technique at a frequency of ISM band. A stable communication and operation is achieved as the two types of channels are separated. Implemented in a compact size enough to be implanted in human body, the system exhibits good performance in experimental studies.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2008.04a
• /
• pp.168-173
• /
• 2008

본 연구는 UKF Algorithm을 이용한 정전용량형 원격RF센서시스템을 개발하였다. 원격 RF센서 시스템이란 wireless, implantable 그리고 batterless을 만족하는 센서 시스템을 의미한다. 기존의 원격 RF센서 시스템은 보편적으로 집적회로 타입을 채택하지만, 그 구조의 복잡성과 전력소모의 제약을 받는다. 이러한 제약을 해결하기 위해 본 연구에서는 R, L 그리고 C만으로 구성되어있는 유도결합원리를 이용한 원격 RF센서 시스템을 제안하였다. 제안된 RF 센서 시스템은 압력 혹은 습도와 같은 환경의 변화를 정전용량 값으로 측정할 수 있으며 센서의 정전 용량 값을 측정하기 위해 비선형시스템의 파라메타추정에 적합한 Unscented Kalman Filter(UKF) 기법을 채택하였다. UKF 기법을 이용하기 위해 제안된 시스템은 페이저법을 사용하여 수학적으로 모델링되었다. 마지막으로, 제안된 UKF 알고리즘을 이용한 원력 RF센서시스템이 잡음환경에서도 정전용량값을 비교적 정확하게 추정가능함을 확인하였다.