• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.1030-1035
• /
• 2011

The remote control of mobile robot is widely used to perform dangerous and complex tasks such as underwater exploration and cleaning of nuclear reactor. For this purpose, the obstacle avoidance process will proceed to ensure a safe drive. In this paper, we tested that mobile robot drive in which replaced a pipe with a box. After we measured the distance around the obstacle through a sensor of robot, we got the information that changed haptic force from the distance of the obstacle.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_2
• /
• pp.627-635
• /
• 2020

In this study, the optimal support span determination of pipeline system was carried out in consideration of the effects of seismic loads. The theoretical support and structural analysis were used to determine the optimal support span of piping system according to pipe diameter using theoretical and structural deflection criteria. The reliability of the analysis results was secured by comparing the structural and theoretical results. In particular, the optimum support span of piping system was obtained by considering the effects of seismic load, and the optimal support span of pipe diameter and piping system tended to be proportional to each other. When considering the effects of earthquakes on different pipe diameters(300~2,500mm), the span length is reduced by up to 48% at the allowable stress criterion, and the pipe span length is reduced by up to 5.9% at the deflection criterion. It can be seen that the effect of the seismic load on the determination of the piping span length has a greater effect on the stress than the displacement.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.3
• /
• pp.315-321
• /
• 2021

In this study, the natural frequency analysis of the fuel pipe and vibration test jig was performed as a basic study to determine the vibration characteristics of the vehicle's fuel pipe and the stability analysis of fatigue failure of the pipe. The natural frequencies of the fuel pipe and the fuel pipe with the test jig were calculated and the results were compared. As a result of the analysis, it was found that the natural frequency of the fuel pipe and the natural frequency of the test jig differed about 7 times, so that the vibration of the test jig did not affect the vibration of the fuel pipe. In addition, as a result of the natural frequency analysis of the fuel pipe itself and the pipe with the test jig attached, the maximum error is less than about 1%. In the future, it was suggested that the analysis of the design changed fuel pipe may be performed without a test jig.

• Nuclear Engineering and Technology
• /
• v.50 no.4
• /
• pp.613-618
• /
• 2018

We are developing a shared remote control mobile robot for aerial work in nuclear power plants (NPPs); a robot consists of a mobile platform, a telescopic mast, and a dual-arm slave with a working tool. It is used at a high location operating the manual operation mechanism of a fuel changer of a heavy water NPP. The robot system can cut/weld a pipe remotely in the case of an emergency or during the dismantling of the NPP. Owing to the challenging control mission considering limited human operator cognitive capability, some remote tasks require a shared control scheme, which demands systematic software design and integration. Therefore, we designed the architecture of the software systematically.

• Laser Solutions
• /
• v.12 no.1
• /
• pp.19-24
• /
• 2009

Because of its fast and precise welding performance, laser welding is becoming a new excellent welding method. However, the precise focusing and robust seam tracking are required to apply laser welding to the practical fields. In order to laser weld a type of T joint like a circular pipe on a square pipe, which could be met in the three dimensional structure such as an aluminum space frame, a visual sensor system was developed for automation of focusing and seam tracking. The developed sensor system consists of a digital CCD camera, a structured laser, and a vision processor. It is moved and positioned by a 2-axis motorized stage, which is attached to a 6 axis robot manipulator with a laser welding head. After stripe-type structured laser illuminates a target surface, images are captured through the digital CCD camera. From the image, seam error and defocusing error are calculated using image processing algorithms which includes efficient techniques handling continuously changed image patterns. These errors are corrected by the stage off-line during welding or teaching. Laser welding of a circular pipe on a square pipe was successful with the vision tracking system by reducing the path positioning and de focusing errors due to the robot teaching or a geometrical variation of specimens and jig holding.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.72-77
• /
• 2018

In this study, cutting robot system which could cut lateral protrusion into main pipes at the connection of sewer pipes was developed. In addition, the cutting test of the robot for the lateral protrusions were performed. The test parameters included materials used in the main pipes and diameters of the pipes, and materials used in the protruded pipes. The materials type of the main pipes were concrete and PE, and the diameters of the pipes were 300 and 500 mm. The materials type used in the protruded pipes were PE and PVC, and the diameter of the pipes was 100 mm. Remaining length of each lateral protruded pipe was less than 5 mm which was an target value of cutting performance. It showd that test results were within the target value. Therefore, in the repair of sewer pipes, the lateral protruded pipes can be cut by using the robot system developed in this paper.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.7
• /
• pp.697-703
• /
• 2011

This article describes a snake robot with 2-DOF actuator modules. The 2-DOF actuator modules make the snake robot move in the 3D space so that the snake robot can cross obstacles and rough terrain. Each 2-DOF actuator module is designed to have high torque output and an embedded controller. A cross bracket connecting the modules is designed be able to support the weight of two actuator modules. The developed snake robot shows 3-D motions such as side winding, standing/monitoring, and can climb in a narrow pipe with high torque modules. The snake robot moves fast with passive wheels in a plane while crossing obstacles.

• Korean Journal of Construction Engineering and Management
• /
• v.19 no.6
• /
• pp.115-123
• /
• 2018

The primary objective of this study is to develop an all-in-one based steel pipe pile cutting robot prototype that improves the conventional steel pipe pile head cutting work in safety, quality, and productivity. For this, the following research works are conducted sequentially; 1)literature review and expert survey, 2)selection of core technology using AHP analysis, 3)deduction of detail design, 4)verification of structural stability, 5)development of full-scale prototype. As a result leveling laser and laser detector(94.46), plasma cutter(96.72), rotary grapple(98.45) are selected as a core technologies. As an outcome, it is analyzed that gripper, cylinder pivot bracket and gripper base are structurally stable. Their maximum stresses are shown as 43.0%, 19.4%, 5.3% compared to their yield strength respectively. The development of full-scale prototype in this study will be utilized for the development of the all-in-one attachment based steel pipe pile cutting robot commercialization model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.789-795
• /
• 2010

For the reliable clamping of a robotic colonoscope inside the colon, we propose a clamping module consisting of six legs at the front and a trigger at the rear. In addition, a pneumatic-line based locomotive mechanism, which was developed previously for in-pipe inspection, is adopted to reduce the friction force between the pneumatic lines and the locomotion environment. In order to evaluate locomotion performance, a robot with a diameter of 15 mm and a length of 110.250 mm is used. Based on control signal from LabVIEW, it is tested in acrylic pipe and pig's colon. The proposed robot is able to move in the curved path which has a radius of over 25 mm. The speed of the robot is 33 mm/s in a straight path and 12.1 mm/s on a vertical path. The proposed robot, which has one pneumatic line and two clamping modules, conclusively shows reliable locomotion performance under in vitro condition.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.225-229
• /
• 2006

The issue with the drainpipe now a day is that they are laid underground. Causing us to perform additional work to repair, such as digging up the ground and peeling off the insulator that surrounds the pipe. And such series works are difficult that concession appears from government and municipal office. However, if we can save time and money. Performance of piping robot that we are studied in existing session through fixing unit and improvement of cutting bit shorten and wished to heighten work efficiency. And we are trying to develop a unit that can cut up the projecting parts which connects with the interior part of the drainpipes.