• 한국전자통신학회논문지
• /
• 제9권10호
• /
• pp.1169-1174
• /
• 2014

본 논문은 토양 수분 함유량 검출을 위한 L-band 마이크로파 라디오미터의 주파수 선택 및 우수한 수신감도를 위한 하모닉 억압의 헤어핀 필터에 관한 것이다. 전형적인 반파장 공진기가 공진주파수의 배수에서 하모닉을 가지는 것에 비해, 각 부분의 임피던스 비와 전기적 길이 비로써 하모닉 주파수를 조절할 수 있는 SIR을 이용하여 하모닉 억압 특성을 구현하였다. 필터의 하모닉을 효율적으로 억압하기 위해 5단의 헤어핀 필터에는 서로 다른 임피던스 비를 갖는 3종류의 SIR이 사용되었고, 제작된 필터는 1390 [MHz]의 중심주파수의 5배 주파수까지 35 [dB] 아래로 하모닉을 억압하는 특성을 가진다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제10권4호
• /
• pp.300-308
• /
• 2010

This paper describes the development of a low-power electrocardiogram (ECG) touch sensor intended for the use with two dry metal electrodes. An equivalent ECG extraction circuit model encountered in a ground-free two-electrode configuration is investigated for an optimal sensor read-out circuit design criteria. From the equivalent circuit model, (1) maximum sensor resolution is derived based on the electrode's background thermal noise, which originates from high electrode-skin contact impedance, together with the input referred noise of instrumentation amplifier (IA), (2) 60 Hz electrostatic coupling from mains and motion artifact are also considered to determine minimum requirement of common mode rejection ratio (CMRR) and input impedance of IA. A dedicated ECG read-out front end incorporating chopping scheme is introduced to provide an input referred circuit noise of 1.3 ${\mu}V_{rms}$ over 0.5 Hz ~ 200 Hz, CMRR of IA > 100 dB, sensor resolution of 7 bits, and dissipating only 36 ${\mu}W$. Together with 8 bits synchronous successive approximation register (SAR) ADC, the sensor IC chip is implemented in 0.18 ${\mu}m$ CMOS technology and integrated on a 5 cm $\times$ 8 cm PCB with two copper patterned electrodes. With the help of proposed touch sensor, ECG signal containing QRS complex and P, T waves are successfully extracted by simply touching the electrodes with two thumbs.

• Journal of Power Electronics
• /
• 제17권1호
• /
• pp.305-313
• /
• 2017

A novel interference isolation method is proposed by using several designed coils in capacitive power transfer systems as isolation impedances. For each designed coil, its stray parameters such as the inter-turn capacitance, coil resistance and capacitance between the coil and the core, etc. are taken into account. An equivalent circuit model of the designed coil is established. According to this equivalent circuit, the impedance characteristic of the coil is calculated. In addition, the maximum impedance point and the corresponding excitation frequency of the coil are obtained. Based on this analysis, six designed coils are adopted to isolate the interference from power delivery. The proposed method is verified through experiments with a power carrier frequency of 1MHz and a data carrier frequency of 8.7MHz. The power and data are transferred parrallelly with a data carrier attenuation lower than -5dB and a power attenuation on the sensing resistor higher than -45dB.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 D
• /
• pp.2184-2186
• /
• 2001

The research presented in this paper focuses on a method for the detection of High Impedance Fault(HIF). The method will use the fast wavelet transform and neural network system. HIF on the multi-grounded three-phase four-wires primary distribution power system cannot be detected effectively by existing over current sensing devices. These paper describes the application of fast wavelet transform to the various HIF data. These data were measured in actual 22.9kV distribution system. Wavelet transform analysis gives the frequency and time-scale information. The neural network system as a fault detector was trained to discriminate HIF from the normal status by a gradient descent method. The proposed method performed very well by proving the right state when it was applied staged fault data and normal load mimics HIF, such as arc-welder.

• Macromolecular Research
• /
• 제16권4호
• /
• pp.308-313
• /
• 2008

A simple strategy was developed based on polyelectrolyte/silver nanocomposite to obtain humidity-sensitive membranes. The major component of a humid membrane is the polyTEAMPS/silver nanocomposite obtained by thermal heating the mixture of a polyelectrolyte and silver isopropylcarbamate complex. Humidity sensors prepared from polyTEAMPS/silver (w/w=100/0 and 100/6) nanocomposites had an average impedance of 292, 8.83 and $0.86\;k{\Omega}$, and 5,327, 140 and $0.93\;k{\Omega}$ at 30,60 and 95% relative humidity (RH), respectively. Hysteresis, temperature dependence and response time were also measured. Activation energies and complex impedance spectroscopy of the various components of the polyelectrolyte/silver nanocomposite films were examined for the humidity-sensing membrane.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.521-524
• /
• 2009

신경자극반응 측정 플랫폼을 구현하는데 있어서 손가락 움직임을 감지하는 것이 중요한 요소로 작용하고 있다. 이것은 손가락의 움직임에 따라 신경자극과 근육반응이 달라지기 때문이다. 즉, 손가락의 움직임을 감지해서 신경 자극 Actuator 및 근육 반응 감지를 위한 H/W 개발이 필요한 것이다. 또한 임베디드 기반으로 가기위한 저전력 CPU를 사용하였다. H/W 구성은 isolation power부분, 정전류조절, High impedance INA, 증폭기부분이 있으며 Micro-controller에서는 stimulus mode 및 Current 의 상태를 통제하고, AD converter를 통해 얻어진 Low Data를 처리 시스템을 구현한다.

• 한국재료학회지
• /
• 제21권8호
• /
• pp.468-475
• /
• 2011

[ $LaMeO_3$ ](Me = Cr, Co) powders were prepared using the polymeric precursor method. The effects of the chelating agent and the polymeric additive on the synthesis of the $LaMeO_3$ perovskite were studied. The samples were synthesized using ethylene glycol (EG) as the solvent, acetyl acetone (AcAc) as the chelating agent, and polyvinylpyrrolidone (PVP) as the polymer additive. The thermal decomposition behavior of the precursor powder was characterized using a thermal analysis (TG-DTA). The crystallization and particle sizes of the $LaMeO_3$ powders were investigated via powder X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and particle size analyzer, respectively. The as-prepared precursor primarily has $LaMeO_3$ at the optimum condition, i.e. for a molar ratio of both metal-source (a : a) : EG (80a : 80a) : AcAc (8a) inclusive of 1 wt% PVP. When the as-prepared precursor was calcined at $700^{\circ}C$, only a single phase was observed to correspond with the orthorhombic structure of $LaCrO_3$ and the rhombohedral structure of $LaCoO_3$. A solid-electrolyte impedance-metric sensor device composed of $Li_{1.5}Al_{0.5}Ti_{1.5}(PO_4)_3$ as a transducer and $LaMeO_3$ as a receptor has been systematically investigated for the detection of NOx in the range of 20 to 250 ppm at $400^{\circ}C$. The sensor responses were able to divide the component between resistance and capacitance. The impedance-metric sensor for the NO showed higher sensitivity compared with $NO_2$. The responses of the impedance-metric sensor device showed dependence on each value of the NOx concentration.

• Corrosion Science and Technology
• /
• 제6권5호
• /
• pp.261-268
• /
• 2007

Embedded sensors were used as an in-situcorrosion-sensing device for aircraft and vehicular structures protected by organic coatings. Results are presented changes associated with a standard Airforce aircraft coating and a standard Army vehicle coating were monitored by embedded sensors. These coatings consisted of a polyurethane topcoat and an epoxy primer, however are formulated to provide different characteristics. The ac-dc-ac testing method was used to accelerate the degradation of these coatings while being immersed in a NaCl medium. Electrochemical impedance spectroscopy and electrochemical noise measurement experiments were used to monitor the induced changes. A comparison of the results between coatings subjected to the ac-dc-ac exposure and coatings subjected to only constant immersion in the NaCl medium is presented. The results were used to demonstrate the effectiveness of the ac-dc-ac method at accelerating the degradation of an organic coating without observably changing the normal mechanism of degradation. The data highlights the different features of the coating systems and tracks them while the coating is being degraded. The aircraft coating was characterized by a high-resistant topcoat that can mask corrosion/primer degradation at the primer/substrate interface whereas the vehicle coating was characterized by a low-resistant topcoat with an effective corrosion inhibiting primer. Details of the ac-dc-ac degradation were evaluated by using an equivalent circuit to help interpret the electrochemical impedance data.

• Journal of electromagnetic engineering and science
• /
• 제12권4호
• /
• pp.227-233
• /
• 2012

This paper describes a novel and compact biosensing platform using an RF active system. The proposed sensing system is based on the oscillation frequency deviation due to the biomolecular binding mechanism on a resonator. The impedance variation of the resonator, which is caused by a specific biomolecular interaction results in a corresponding change in the oscillation frequency of the oscillator so that this change is used for the discrimination of the biomolecular binding, along with concentration variation. Also, a Surface Acoustic Wave (SAW) filter is utilized in order to enhance the biosensing performance of our system. Because the oscillator operates at the skirt frequency range of the SAW filter, a small amount of oscillation frequency deviation is transformed into a large variation in the output amplitude. Next, a power detector is used to detect the amplitude variation and convert it to DC voltage. It was also found that the frequency response of the biosensing system changes linearly with three streptavidin concentrations. Therefore, we expect that the proposed RF biosensing system can be applied to bio/medical applications capable of detecting a nano-sized biomolecular interaction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 D
• /
• pp.3016-3018
• /
• 2005

The PSD(Position Sensitive Detector) is a sensor for detecting the position of incident light. Because of its various advantages, it is used for position and angle sensing, optical range finders, laser displacement sensing, and etc. In the previous study of the position finding system, the laser tracking robot is developed. Small data rate and unidirectionality is the characteristics of data communication both DSP-based pan/tilt control board and the robot. If we can transmit data to the target using PSD sensor and laser diode module, there is no need for communication devices such as the bluetooth and wireless module. For this reason, this paper presents the new method for data transmission. Transmit data using RS-232 is modulated by a VTF(Voltage To Frequency) converter The laser diode module transmits the modulated data. And then the PSD sensor receive that data. Demodulation process is accomplished by the system which is consisted with trans-impedance amplifier, FTV(Frequency To Voltage) converter, and etc.