• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.319-322
• /
• 2002

In this Paper, we suggested the Half-Bridge inverter for the automotive HID electronic ballast. electronic ballast for automotive HID lamp should be supplied by low-frequency square wave avoiding the acoustic resonance(11kHz ∼ 825kHz). When the HID lamp is hot state, the electronic ballast should supply the sufficient current for a few milli-second to the lamp at the re-strike ignition state. that is called take-over current. We have introduced the new take-over current control method that could have reduced the peak current and supplied the sufficient take-over current.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• 제56권3호
• /
• pp.148-154
• /
• 2007

In this paper, characteristics of ignition voltage and current by wire length of HID(High Intensity Discharge) lamp circuit are analyzed. In the construction field, decision of the wire thickness for HID lamp circuit has the problems, and these are presented. Through transmit parameters, equivalent model of the ballast and HID lamp circuit was derived. The graph of voltage reduction about length between the ballast and the lamp is shown. The simulation of proposed model and experimental results are presented in order to validate the proposed method. The proposed model and graph can use to choose the proper length of wire between the ballast and the lamp in the field.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2088-2090
• /
• 1998

A low-cost electronic starter is developed to decrease ignition failure significantly through successive starting trial and to prevent overheating at the end of fluorescent lamp life. Moreover, it has an additional feature of being capable of ignition at the recovered lamp voltage without any circuit correction. The developed electronic starter is consisted of four parts - a half wave rectifier circuit, a timer circuit, a switching circuit and a protection circuit. The protection circuit made up of a transistor and capacitors utilizing capacitive characteristics, carries out successive starting trial and end-of-life protection. Lamp ignition is completed within 0.5 seconds with taking advantage of a high preheating current from the half-wave rectifier circuit. Nevertheless, its performance is proved to be very excellent through a standard switching endurance test.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1007-1009
• /
• 2008

This paper presents an architecture for driving multiple paralleled cold cathode fluorescent lamps (CCFLs) for back lighting applications. The key to the architecture is a proposed capacitive coupling approach for lamp ignition. This system is consist of a flyback converter, a single inverter to drive multiple lamps and conductive floating reflector. The topology is capable of driving a number of parallel lamps with independent accurate lamp, current regulation and improving cost effectiveness with significant reduction in size and weight, compared to typical high frequency ac ballast. Experimental demonstration results for ten of parallel CCFLs with simultaneous ignition. This like the EEFL it will be able to use the CCFL is the thing. Also, it investigates the effect where the leakage current goes mad to the Lamp.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.31-35
• /
• 2003

This paper presents a microprocessor controlled digital ballast for HID lamps, which gives intelligent features such as a precise power control, optimum ignition voltage and detection of end of life. Average current mode PFC is employed for reducing EMI and a universal input. Direct spread spectrum is done by applying 1 KHz triangular wave for removing acoustic resonance. This frequency modulation of 1 KHz gives also low EMI level and no ripple on lamp current. The microprocessor controls the voltage of DC-bus, the voltage of ignition pulses, the power of output and the bandwidth of spread spectrum. A 250W digital ballast is implemented with an efficiency of 93％ and a maximum EMI level of 55 ㏈${\mu}$V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제10권4호
• /
• pp.652-658
• /
• 2006

This paper deals with an electronic ballast for hish intensity short-arc discharge lamps, which consists of a boost converter, a step down converter operated as a current source with power regulation and a low frequency inverter with external ignition circuit The ignition circuit generates high voltage pulses of 130[Hz] up to 5 [kV]. A reignition circuit is equipped in the ballast, and it operates the lamp at a regular interval for protection when an ignition fails. Acoustic resonance phenomenon was eliminated by operating a low frequency square wave voltage and current. The measured lamp voltage, current and consumption power were 123.8 [V], 8.1 [A] and 1,002 [W], respectively. From the experiment, we confirmed that the prototype ballast operates the lamp with a constant power.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제8권4호
• /
• pp.18-25
• /
• 2000

Ion current in an S.I engine cylinder is measured with the spark plug as a probe. The peak values are confirmed to show a fair correlation with local air-fuel ration and engine speed which implies that the ion current measured at the spark plug may provide a signal for the local mixture strength which is the key parameter in precise fuel control for future engines especially of gasoline direct-injected lean burn engines.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.949-952
• /
• 2011

Study on differential pressure in the chamber of cannon by adjusting the mass flow of ignition-gas has been conducted using the 1-D interior ballistics numerical code called IBcode. In case of large-caliber cannon, high temperature ignition-gas is injected to the chamber through the side hole of the primer to ignite the propellant. Therefore, mass flow of injected ignition-gas affects the propellant combustion in the chamber. Mass flow of each side hole of the current primer was uniformly distributed. In this study, differences of propellant combustion with different mass flow of each side hole have been imposed. Results in case of the mass flow increase in the direction to the base show that the differential pressure decreases compared to the uniformed mass flow.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제25권2호
• /
• pp.149-156
• /
• 2017

Various kinds of accessories(e.g., clock, radio, automatic door locks, alarm devices, etc.) or unit components (e.g., black box, navigation system, alarm, private audio, etc.) require dark current even when the vehicle power is turned off. However, accessories or unit components can be the causes of excessive dark current generation. It results in battery discharge and the vehicle's failure to start. Therefore, immediate detection of abnormal dark current and response are very important for a successful repair job. In this paper, we can increase the maintenance efficiency by presenting a standardized diagnostic process for the measurement of the dark current and the existing problem. As a result of the absence of a system to block the dark current in a vehicle, diagnosis and repair were performed immediately by using a standardized dark current diagnostic process.

• Journal of the Korean Society of Propulsion Engineers
• /
• 제18권1호
• /
• pp.26-32
• /
• 2014

In this study, DC (Direct current) type steam plasma igniter is developed for effective ignition of high-energy density metal aluminum and gas temperature is measured by emission spectrum of OH radical. Because of the ultra-high gas temperature, the DC plasma jet is measured by Boltzmann plot method which is the non-contact optical technique and spectrum comparison-analysis. And both methods were applied to experiment after accurate verification. As a result, we could identify that plasma jet temperature is 2900 K ~ 5800 K in the 30 mm range from the nozzle tip.