• Progress in Superconductivity
• /
• v.5 no.1
• /
• pp.70-74
• /
• 2003

We fabricated cube textured Ni substrate for YBCO coated conductor and evaluated the effects of processing parameters on microstructural evolution and texture formation. Ni-rods as an initial specimen were prepared by two different methods, i.e., powder metallurgy(PM) and plasma arc melting(PAM). Subsequently, the rods were cold rolled to 100 $\mu\textrm{m}$ thick substrate and annealed at temperatures of $700∼1200^{\circ}C$. The texture of the substrate was characterized by pole-figure. It was observed that the texture of substrate made by P/M did not significantly varied with annealing temperature of 600∼$l100^{\circ}C$ and the full-width at half-maximums (FWHM) of both in-plane and out-of-plane were 9$^{\circ}$∼$10^{\circ}$. On the other hand, the texture of substrate made by PAM was more dependent on the annealing temperature and the corresponding values were $9^{\circ}$ ∼$13^{\circ}$ at the temperature range. In addition, recrystallization twin texture, (221)＜221＞, was formed as the temperature increased further. OM profiles showed that the grain size of substrate made by P/M was smaller than that made by PAM and this difference was correlated to the microstructure of initial specimens.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1732-1734
• /
• 2001

The purpose of this experiment was to develope Triggered Vacuum Switch(TVS) and to improve understanding of the high current vacuum arc phenomena in the TVS. The TVS has an array of rods of alternate polarity in which a fixed gap spacing is maintained between the rods. The cross section of each rod has trapezoidal shape. Breakdown of the TVS produced high current vacuum arc plasma. A spectroscopic measurement was performed over 20 kA peak current in the center of electrodes, in the vicinity of cathode, and outside electrodes. The electrode material tested was Fe. Measured Fe spectrum range was from 200 nm to 900 nm. Measurement result showed that over 90 percent of the charge states were FeII and the others were FeI and FeIII. The electron temperature was determined from the relative line intensity ratio methode of FeII system by assuming the local thermal equilibrium(LTE). The electron temperature at the center of electrodes was measured as 1.5 eV at 26 kA peak current. The electron temperature varied with its peak current. Intensity of spectrums is the highest in the vicinity of the cathode. Further we will also present study result of the diode phenomena in the TVS.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.417-424
• /
• 2011

A fuel assembly consists of five major components, i.e., a top end piece (TEP), a bottom end piece (BEP), spacer grids (SGs), guide tubes (GTs) and an instrumentation tube (IT); in addition, it also includes fuel rods (FRs). The TEP/BEP should satisfy stress intensity limits according to the conditions A and B of ASME, Section III, Division 1-Subsection NB. In a dual-cooled fuel assembly, the array and position of fuel rods are different from those in a conventional PWR fuel assembly; these changes are necessary for achieving power uprating. The flow plates of the TEP and BEP have to be modified accordingly. The pattern and shape of the flow holes were newly designed. To verify the strength compatibility, the Tresca stress limit according to the ASME code was investigated in the case of an axial load of 22.241 kN. In this paper, the stress linearization procedure for strength evaluation of a newly designed TEP is presented.

• Asian-Australasian Journal of Animal Sciences
• /
• v.5 no.2
• /
• pp.323-327
• /
• 1992

An experiment was conducted to determine whether there were any apparent differences in the microbial population, colonization pattern and digestion of guinea grass in situ, between cattle and swamp buffalo. Percentage losses in dry matter (DM), nitrogen (N) and neutral detergent fibre (NDF) of guinea grass were significantly (p<0.01) higher when incubated in the rumen of buffalo than in cattle. Buffalo also showed significantly (p<0.05) faster degradation rates than cattle for each grass component (DM, N, DNF). Light microscopy and SEM examination of the incubated grass materials showed that there were no apparent differences in the pattern of bacterial and fungal invasion and colonization of the grass materials between cattle and buffalo. Attachment of bacteria and fungal zoospores on the grass fragments occurred at 15 min after rumen incubation. After 3 h of rumen incubation, dense population of bacteria was observed in the thin-walled mesophyll and parenchyma tissues, whereas root-like fungal rhizoids were observed in both thin-walled and thick-walled cells. By 6 h, eroded zones were apparent in the thin-walled tissues and in thick-walled tissues with profuse rhizoids. After 24. 48 and 72 h of rumen incubation, most thin-walled tissues were degraded leaving mostly the thick-walled tissues. The predominant bacteria were the curved rods resembling Butyrivibrio sp., the thick rods resembling Fibrobacter sp., the diplococcoids resumbling Ruminococcus sp. And spirochetes. Fungi were predominantly those with spherical or oval sporangia. Fusiform sporangia with acuminate apices which resembled Ruminomyces sp. Were of lesser occurrence. Few protozoa were found on the grass fragments at all incubation times.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.338.2-338.2
• /
• 2016

Al doped ZnO (AZO) thin films were deposited on Si substrates with rod-shaped-surface by pulsed laser deposition method (PLD). Si-rods were prepared through chemical etching. To analyze the influence on the formation of the rod structure, samples with various chemical etching conditions such as AgNO3/HF ratio, etching time, and solution temperature were prepared. The morphology of Si-rod structures were examined by FE-SEM. Fig. 1 shows a typical structure of n-AZO/p-Si-rod juncions. The fabricated n-AZO/p-Si-rod devices exhibited p-n diode current-voltage characteristics. We compared the I-V characteristics of n-AZO/p-Si-rod devices with the samples without Si-rod structure.

• Structural Engineering and Mechanics
• /
• v.47 no.3
• /
• pp.345-359
• /
• 2013

For the purpose of investigating the free vibration response of the spatial curved beams, the governing equations are derived in matrix formats, considering the variable curvature and torsion. The theory includes all the effects of rotary inertia, shear and axial deformations. Frobenius' scheme and the dynamic stiffness method are then applied to solve these equations. A computer program is coded in Mathematica according to the proposed method. As a special case, the dynamic stiffness and further the natural frequencies of a cylindrical helical spring under fixed-fixed boundary condition are carried out. Comparison of the present results with the FEM results using body elements in I-DEAS shows good accuracy in computation and validity of the model. Further, the present model is used for reciprocal spiral rods with different boundary conditions, and the comparison with FEM results shows that only a limited number of terms in the resultant provide a relatively accurate solution.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.5 no.3
• /
• pp.52-63
• /
• 1995

A neuro-fuzzy algorithm is presented for nuclear reactor power control in a pressurized water reactor. Automatic reacotr power control is complicated by the use of control rods because of highly nonlinear dynamics in the axial power shape. Thus, manual shaped controls are usually employed even for the limited capability during the power maneuvers. In an attempt to achieve automatic shape control, a neuro-fuzzy approach is considered because fuzzy algorithms are good at various aspects of operator's knowledge representation while neural networks are efficinet structures capable of learning from experience and adaptation to a changing nuclear core state. In the proposed neuro-fuzzy control scheme, the rule base is formulated based ona multi-input multi-output system and the dynamic back-propagation is used for learning. The neuro-fuzzy powere control algorithm has been tested using simulation fesponses of a Korean standard pressurized water reactor. The results illustrate that the proposed control algorithm would be a parctical strategy for automatic nuclear reactor power control.

• Journal of Photoscience
• /
• v.3 no.3
• /
• pp.127-132
• /
• 1996

Calcium has a variety of functions in neuron and muscle cells and blood clotting, especially in the visual system where dark adapted rods cotransport with Na$^+$ into the cell. An influx of Ca$^{2+}$ flows out of the cell through the Na$^+$ - Ca$^{2+}$ exchanger. By using a modified Ussing chamber in order to bring in vivo environment close, we have concluded that Ca$^{2+}$ blocks the activity of guanylate cyclase; in consequence, having an effect on the amplitude of electroretinogram (ERG). We suggest that Ca$^{2+}$ moves between the photoreceptor and the vitreous humor by way of certain Ca$^{2+}$ transport mechanisms. Also, the effect of Zn$^{2+}$ in Ca$^{2+}$ - free ringer solution caused an elevation of amplitude in ERG and a reduction of threshold.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.269-270
• /
• 1998

Image-guided surgery (IGS) system has become well known in the field of neurosurgery and spine surgery. A patient's anatomy is first registered to preoperatively acquired CT/ MRI data using the point matching algorithm. A magnetic field digitizer was used to measure the physical space data and the system was based on Workstation of Unix system. To evaluate the spatial accuracy of interactive IGS system, the phantom consisting of rods varied height and known location was used. The RMS error value between CT/MR images and real location was 3-4mm. For the more convenience of the surgery, we provide various image display modules.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1494-1496
• /
• 1997

The MRI Magnet is a most practical application of NbTi superconductor. In this paper, we present the main research results on superconducting wires for MRI magnet which we have developed. Cu/NbTi superconducting wires were fabricated by repeat of cold working and heat-treating process after that billets were extruded. We investigated the relation of superconductivities of wires and heat treatment condition. The correlation between cross section shape of wires and work inhomogeneity of NbTi rods was investigated by microscopic observation. The more repeatation number of cold working and heat-treating process, the higher critical current is achieved.