• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.253-257
• /
• 2005

A tube hydroformability testing system was designed and fabricated so as to observe the forming process and to apply forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The forming limit diagram of A6063 extruded tube, of 40.6 mm outer diameter and 2.25 mm thickness, was successfully obtained through free bulging and T-forming tests except the region of high positive minor strain. It is found that the data points marked on the FLD are mostly located near the strain paths from the finite element analysis excluding the cases of large axial feed. There exist data points even in the area beyond the uniaxial tension mode, since the reduction in thickness decreases due to the axial feed. The forming limit from T-forming test was considerably lower than that from free bulge test. It seems because the deformation is localized at the pole.

• Corrosion Science and Technology
• /
• 제11권2호
• /
• pp.37-42
• /
• 2012

Recent issues in the automotive industries are, improvement of fuel efficiency according to the worldwide $CO_2$ regulation, passenger safety through enhanced crashworthiness, superior design and cost reduction due to price fluctuation of raw material. To meet these demands, steelmaking companies are developing advanced high strength steel and new process technologies such as hydroforming, TWB(Tailor Welded Blank), hot stamping and so on. In addition, eco-friendly and high corrosion resistant coating technologies are getting more attention to comply with the environmental regulations. In this paper, reviews and prospects of recent coating technologies for automotive use are presented.

• 소성∙가공
• /
• 제14권6호
• /
• pp.514-519
• /
• 2005

A tube hydroformability testing system was designed and fabricated enabling to apply the forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The free-bulging and T-forming tests were carried out on the extruded aluminum (A6063) tube specimens with 40.6 mm outer diameter and 2.25 mm thickness. Nine different combinations of internal pressure and axial feed, yielding different strain paths from one another, were taken into consideration in order to induce bursting at various deformation modes. Major and minor strains were automatically measured from deformed grids around the fracture using a stereo-vision-based surface strain measurement system, named ASIAS. The forming limit diagram of the A6063 tube material was successfully obtained. Most of the data points acquired from free bulging and T-forming tests appeared in the range of negative minor strain on the FLD and are mostly located near the strain paths calculated from explicit finite element simulations. The forming limit obtained from tests after pre-tension was considerably lower than that from tests without pre-tension, which showed the strain path-dependency of the forming limit as well known in the sheet forming fold.

• 한국정밀공학회지
• /
• 제33권4호
• /
• pp.247-255
• /
• 2016

Sheet metal-forming processes such as stamping, deep drawing, bending, shearing, hydroforming, hydromechanical deep drawing, rubber forming, and incremental forming have been widely used in the automotive, aircraft, and ship-building industries. With the expansion of the automotive industry, research on these processes has been remarkably developed in Korea since the 1980s. Here, we review the history of this research as well as recent trends in sheet metal-forming processes. This overview focuses specifically on the results of research in Korea and on the works of Professor D.Y. Yang, in honor of his retirement.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권7호
• /
• pp.587-592
• /
• 2016

LNG 선박용 벨로우즈는 극한의 환경에서 지속적인 진동 그리고 큰 온도변화에 따른 수축과 팽창을 견뎌내야 하는 피로수명과 해수환경에서의 내식성을 가져야 한다. 이러한 특성을 갖기 위해서는 저온에서의 인성이 강하고 내부식성이 강한 재료를 사용하여 최적화된 성형조건을 유지하는 것이 매우 중요하다. 이를 위해서는 벨로우즈의 최적화된 설계 조건과 성형방법이 뒷받침되어야 한다. 본 연구에서는 기계적 강성과 신뢰성이 높은 극저온용 벨로우즈를 개발하기 위하여 유한요소 해석을 통해 벨로우즈를 설계하였다. 또한 두 가지의 성형방법을 통해 설계된 벨로우즈를 제작하여 최적화된 성형조건을 도출하고자 하였다. 기계식 성형방법과 하이드로포밍 방법을 통해 벨로우즈를 성형하고 성형방법에 따른 벨로우즈의 기계적 특성을 비교하기 위하여 성형부의 높이, 두께 및 비커스 경도 값을 측정하였다. 이를 통해 기계식 성형방법으로 제작된 벨로우즈의 경도 값이 하이드로포밍 제작 벨로우즈보다 더 높은 것을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.237-240
• /
• 2003

Deformation surrounding the hole in the tube during the hydro-piercing process has been investigated in this study. The tube is expanded and internally pressurized between upper and lower dies, and a piercing punch is driven forcefully through a cross passage in the die and through the wall of the tube. The pressurized fluid within the tube provides support to the wall of the tube during a piercing step to form a hole in the tube having less deformation surrounding the hole in the tube. The deformation area may be fully retracted to a substantially flat form or partially retracted to a countersunk form. In this study, a mathematical model that can predict deformation surrounding the hole has been proposed and experimentally verified by actual hydro-piercing test.

• 소성∙가공
• /
• 제24권1호
• /
• pp.20-27
• /
• 2015

Hot tensile tests were conducted at different temperatures ranging from $20^{\circ}C$ to $550^{\circ}C$ to evaluate the mechanical properties of Al5052 seamless tubes. Such tubes can provide the technological foundation for complex forming using hot air bulging. Hot air bulging is one of the recently developed hydroforming techniques and it has some limitations in terms of cycle times. The benefits of hot air bulging are weight and cost savings through part consolidation and reduced post-forming processes such as welding and piercing. In order to extend the forming limits of Al lightweight material hot air bulging was investigated. A heated tube was placed in a heated die and sealed at the ends by sealing cylinders. The heated tube was subsequently expanded against the die cavity wall by internal pressure using air medium. The results of the current study show that axial feeding speed and air pressure have an effect on the formability of Al tubes during air bulging at elevated temperatures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.134-137
• /
• 2005

In this paper, a continuous contact treatment has been considered during FE-analysis of the sheet metal forming processes. Because the simulation is usually performed stepwise, the status of contact can change suddenly. In case of implicit scheme, the increment of punch stroke can be chosen as large value. For exact assessment of contact force and friction force between die and sheet, the continuous contact treatment is proposed. The virtual surface of sheet metal is modeled by NURBS curves or surfaces in order to calculate exact contact area and penetration depth. From the geometrical evaluation of contact behavior, additional contact pressure is imposed to the element. The deformation of bending process and hydroforming process are analyzed based on this scheme.

• 한국생산제조학회지
• /
• 제26권4호
• /
• pp.410-417
• /
• 2017

Hydro-forming is being employed increasingly to realize lightweight vehicular parts. The bumper beam produced by this process weighs 30% less than the conventional products with equal stiffness. However, hydro-forming involves complex parameters to obtain the target geometry and low residual stress. Parametric studies are conducted using finite element analysis to obtain optimized process conditions. Through these numerical approaches, the internal and holding pressures and feeder forward stroke along the extruded direction are optimized to achieve low residual stress and to minimize springback. The numerical results are verified by experimental observations made by employing a three-dimensional laser scanner. The numerical and experimental results are compared in terms of the springback. Both results show similar tendencies.

• 소성∙가공
• /
• 제13권2호
• /
• pp.154-159
• /
• 2004

Deformation surrounding the hole in the tube during the hydropiercing process has been investigated in this study. The tube is expanded and internally pressurized between upper and lower dies, and a piercing punch is driven forcefully through a cross passage in the die and through the wall of the tube. The pressurized fluid within the tube provides support to the wall of the tube during a piercing step to form a hole in the tube having less deformation surrounding the hole in the tube. The deformation area may be fully retracted to a substantially flat form or partially retracted to a countersunk form. In this study, a mathematical model that can predict deformation surrounding the hole has been proposed and experimentally verified by actual hydropiercing test.