• 소성∙가공
• /
• 제26권4호
• /
• pp.222-227
• /
• 2017

In order to respond to environmental regulations and increased demand for fuel economy, the demand for lightweight car bodies has grown. Hydroforming of aluminum is one possible solution as it eliminates the need for additional welding to develop closed cross-sectional parts. However, the low formability of aluminum is a limitation of its application. On the other hand, the ductility of materials can be improved at higher temperatures, and hot metal gas forming has been widely applied in the production of lightweight vehicle parts. In this study, aluminum alloy for pipe extrusion was developed by controlling the Mg:Cr:Mn ratio based on AA5083. Mechanical properties of the developed material were examined by tensile test and were applied to a forming simulation. Cold forming simulation for preforming and non-isothermal hot forming simulation for hot metal gas forming were carried out to validate process conditions. A prototype of the sidemember was manufactured under the given process condition. Finally, thickness distribution was compared with finite element analysis results.

• 소성∙가공
• /
• 제14권6호
• /
• pp.514-519
• /
• 2005

A tube hydroformability testing system was designed and fabricated enabling to apply the forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The free-bulging and T-forming tests were carried out on the extruded aluminum (A6063) tube specimens with 40.6 mm outer diameter and 2.25 mm thickness. Nine different combinations of internal pressure and axial feed, yielding different strain paths from one another, were taken into consideration in order to induce bursting at various deformation modes. Major and minor strains were automatically measured from deformed grids around the fracture using a stereo-vision-based surface strain measurement system, named ASIAS. The forming limit diagram of the A6063 tube material was successfully obtained. Most of the data points acquired from free bulging and T-forming tests appeared in the range of negative minor strain on the FLD and are mostly located near the strain paths calculated from explicit finite element simulations. The forming limit obtained from tests after pre-tension was considerably lower than that from tests without pre-tension, which showed the strain path-dependency of the forming limit as well known in the sheet forming fold.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.253-257
• /
• 2005

A tube hydroformability testing system was designed and fabricated so as to observe the forming process and to apply forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The forming limit diagram of A6063 extruded tube, of 40.6 mm outer diameter and 2.25 mm thickness, was successfully obtained through free bulging and T-forming tests except the region of high positive minor strain. It is found that the data points marked on the FLD are mostly located near the strain paths from the finite element analysis excluding the cases of large axial feed. There exist data points even in the area beyond the uniaxial tension mode, since the reduction in thickness decreases due to the axial feed. The forming limit from T-forming test was considerably lower than that from free bulge test. It seems because the deformation is localized at the pole.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.717-718
• /
• 2008

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.17-20
• /
• 2002

Recently tube hydroforming technology has been one of the most important technology in automotive industry in the point of saving weight and high quality for collision accidents. In this paper, experimental studies for axial compression tests of hydroformed tubes are performed to investigate the collapse absorption characteristics. The collapse absorption abilities are discussed and compared for as-received, hydroformed, and press formed tubes.

• Corrosion Science and Technology
• /
• 제11권2호
• /
• pp.37-42
• /
• 2012

Recent issues in the automotive industries are, improvement of fuel efficiency according to the worldwide $CO_2$ regulation, passenger safety through enhanced crashworthiness, superior design and cost reduction due to price fluctuation of raw material. To meet these demands, steelmaking companies are developing advanced high strength steel and new process technologies such as hydroforming, TWB(Tailor Welded Blank), hot stamping and so on. In addition, eco-friendly and high corrosion resistant coating technologies are getting more attention to comply with the environmental regulations. In this paper, reviews and prospects of recent coating technologies for automotive use are presented.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권7호
• /
• pp.587-592
• /
• 2016

LNG 선박용 벨로우즈는 극한의 환경에서 지속적인 진동 그리고 큰 온도변화에 따른 수축과 팽창을 견뎌내야 하는 피로수명과 해수환경에서의 내식성을 가져야 한다. 이러한 특성을 갖기 위해서는 저온에서의 인성이 강하고 내부식성이 강한 재료를 사용하여 최적화된 성형조건을 유지하는 것이 매우 중요하다. 이를 위해서는 벨로우즈의 최적화된 설계 조건과 성형방법이 뒷받침되어야 한다. 본 연구에서는 기계적 강성과 신뢰성이 높은 극저온용 벨로우즈를 개발하기 위하여 유한요소 해석을 통해 벨로우즈를 설계하였다. 또한 두 가지의 성형방법을 통해 설계된 벨로우즈를 제작하여 최적화된 성형조건을 도출하고자 하였다. 기계식 성형방법과 하이드로포밍 방법을 통해 벨로우즈를 성형하고 성형방법에 따른 벨로우즈의 기계적 특성을 비교하기 위하여 성형부의 높이, 두께 및 비커스 경도 값을 측정하였다. 이를 통해 기계식 성형방법으로 제작된 벨로우즈의 경도 값이 하이드로포밍 제작 벨로우즈보다 더 높은 것을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.237-240
• /
• 2003

Deformation surrounding the hole in the tube during the hydro-piercing process has been investigated in this study. The tube is expanded and internally pressurized between upper and lower dies, and a piercing punch is driven forcefully through a cross passage in the die and through the wall of the tube. The pressurized fluid within the tube provides support to the wall of the tube during a piercing step to form a hole in the tube having less deformation surrounding the hole in the tube. The deformation area may be fully retracted to a substantially flat form or partially retracted to a countersunk form. In this study, a mathematical model that can predict deformation surrounding the hole has been proposed and experimentally verified by actual hydro-piercing test.

• 한국정밀공학회지
• /
• 제33권4호
• /
• pp.247-255
• /
• 2016

Sheet metal-forming processes such as stamping, deep drawing, bending, shearing, hydroforming, hydromechanical deep drawing, rubber forming, and incremental forming have been widely used in the automotive, aircraft, and ship-building industries. With the expansion of the automotive industry, research on these processes has been remarkably developed in Korea since the 1980s. Here, we review the history of this research as well as recent trends in sheet metal-forming processes. This overview focuses specifically on the results of research in Korea and on the works of Professor D.Y. Yang, in honor of his retirement.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.992-998
• /
• 2004

During the tube hydropiercing, the region adjacent to the pierced hole will be deformed and will be drawn away from the die block as the punch advances through the wall of the tube. The deformation in the region may range from a substantially flat form to a countersunk form, so called rollover. In this study, the effects of material properties, shape of piercing punches, roundness of tube surface and internal pressure within the tube during piercing on the rollover have been investigated experimentally. The results provide the quantitative variation of rollover at given hydropiercing parameters, and a relationship between the deformed radius and the rollover caused by the deformation has been established.