• Journal of Korea Water Resources Association
• /
• v.48 no.8
• /
• pp.685-693
• /
• 2015

We propose a method for deriving the relationship between channel width and discharge from remote sensing products. Stream widths at points distributed along a river network can be measured from high-resolution remote imagery. Further, corresponding drainage area for these points can be calculated using digital elevation models, making it possible to construct width-drainage area relation. On the other hand, the relationship between the flow discharge and the drainage area is obtained from historical data measured at ground stations. By coupling these two relationships, we can finally derive the width-discharge relationship which comprises an important component of downstream hydraulic geometry. The proposed method was tested for the Nakdong River and the Seomjin River, successfully capturing power-law exponents in the width-discharge relationships reported in earlier studies. The proposed approach can serve as an alternative for obtaining the hydraulic geometry relationship under the limits of ground data.

• Journal of Korean Society on Water Environment
• /
• v.32 no.6
• /
• pp.582-588
• /
• 2016

The hydrological simulation program FORTRAN (HSPF) is a comprehensive watershed model that employs the hydraulic function table (FTABLE) (depth-area-volume-flow relationship) to represent the geometric and hydraulic properties of water bodies. The hydraulic representation of the HSPF model mainly depends on the accuracy of the FTABLES. These hydraulic representations determine the response time of water quality state variables and also control the scour, deposition, and transport of sediments in the water body. In general, FTABLES are automatically generated based on reach information such as mean depth, mean width, length, and slope along with a set of standard assumptions about the geometry and hydraulics of the channel, so these FTABLES are unable to accurately describe the geometry and hydraulic behavior of rivers and reservoirs. In order to compensate the weakness of HSPF for hydraulic modeling, we generated alternate method to improve the accuracy of FTABLES for rivers, using the surveyed cross sections and rating curves. The alternative method is based on the hydraulics simulated by HEC-RAS using the surveyed cross sections and rating curves, and it could significantly improve the accuracy of FTABLES. Although the alternate FTABLE greatly improved the hydraulic accuracy of the HSPF model, it had little effect on the hydrological simulation.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.823-838
• /
• 2003

For many rivers and streams, it has been observed that a single representative discharge may be used to determine the hydraulic geometry of a stable channel. This representative channel forming discharge has been given several names by different researchers, including bankfull, specified recurrence interval, and effective discharge. Therefore, The purpose of this study is to estimate channel forming discharge for study areas using the hydrological characteristic parameters and recording data, and to determine the hydraulic geometry relationships for the relating bankfull dimensions to bankfull discharge. In the Munmak and Seomyun gauging stations, the estimated bankfull discharges are found to have a return period of 1.8 and 1.5 years on the maximum annual series, respectively. The estimated effective discharges at those stations are largely different from bankfull discharges. The hydraulic geometry relationships between bankfull discharge and bankfull width, bankfull depth, velocity, bed slope are established. But the statistical parameters, such as R2, are calculated lower.

• Tunnel and Underground Space
• /
• v.27 no.2
• /
• pp.100-108
• /
• 2017

As a measure of the combined effect of fracture geometry, the fabric tensor parameters could quantify the status of the connected fluid flow paths in discrete fracture network (DFN). The correlation analysis between fabric tensor parameters and hydraulic properties of the 2-D DFN was performed in this study. It is found that there exists a strong nonlinear relationship between the directional conductivity and the fabric tensor component estimated in the direction normal to the direction of hydraulic conductivity. The circular radial plots without significant variation of the first invariant ($F_0$) of fabric tensor for different sized 2-D DFN block are a necessary condition for treating representative element volume (REV) of a fractured rock mass. The relative error (ER) between the numerically calculated directional hydraulic conductivity and the theoretical directional hydraulic conductivity decreases with the increase in $F_0$. A strong functional relation seems to exist between the $F_0$ and the average block hydraulic conductivity.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.4
• /
• pp.1-11
• /
• 2003

In order to measure aperture variation dependent on normal stress and to characterize on relationship between aperture variation and hydraulic conductivity this study measured apertures of rock fractures under a high resolution confocal laser scanning microscope (CLSM) with application of five stages of uniaxial normal stresses. From this method the response of aperture can be continuously characterized on one specimen by different loads of normal stress. The results of measurements showed a rough geometry of fracture bearing non-uniform aperture. They also revealed different values of aperture variations according to the load stages on each position along a fracture due to the fracture roughness. Laboratory permeability tests were also conducted to evaluate the changes of permeability coefficients related to the aperture variations by different loads. The results of permeability tests revealed that the hydraulic conductivity was not reduced at a fixed rate with increase of normal load. Moreover, the rates of aperture variations did not match to those of hydraulic conductivity. The hydraulic conductivity calculated in this study did not follow the cubic law, representing that the parallel plate model is not suitable to express the fracture geometry corresponding to the results of aperture measurements under the CLSM.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.155-155
• /
• 2022

Low head, ogee spillways is popularly used to defense against floods as well as to provide water for irrigation. Spillway is also used to assess compliance with water quality regulations by controlling amount of discharge to the downstream of a channel. For the purpose of water resource management and/or environmental aspects as explained above, the flow discharge through spillways need to be correctly rated as a function of geometry and hydraulic variables. Typically, four flow conditions are encountered during the operation of spillway: (a) uncontrolled free flow (UF); (b) uncontrolled submerged flow (US); controlled free flow (CF); and controlled submerged flow (CS), and each condition has a unique rating equation. However, one of the tricky part of the spillway operation is finding correct flow type over the spillway because structures can operate under both submerged and free flow conditions, and the types are continuously changing over time depending on the amount of discharge, head water and tail water elevation. Quite obviously, if the wrong rating curve relationship is applied because of misjudgment of the flow type due to a transition, a serious error can occur. Thus, an hydraulic model study of one of spillway structure located in South Florida was conducted for the purpose of developing transition relationships. In this presentation, US to UF transition is highlighted.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.129-136
• /
• 2010

Axial piston pumps have been widely used as power sources for hydraulic systems, but studies on the fluid flow within the pump have been usually performed using 1-D analysis because of the difficulties in considering the fluid compressibility, high-speed revolution, variation of the flow rate, and complicated geometry. The goal of this study was to understand the hydraulic fluid flow within axial piston pumps by using the 3-D numerical method and the process of generating discharge pressure ripples. To improve the convergence and robustness of the simulation model, a grid system was constructed with hexahedron-type grids around the valve plate. Furthermore, we employed an empirical formula to describe the relationship between the oil density and pressure. The CFD (computational fluid dynamics) results compared well with the experimental data.

• Tunnel and Underground Space
• /
• v.21 no.2
• /
• pp.128-137
• /
• 2011

The shut-in pressure calculated in common hydrofracturing test for vertical borehole equals generally to the minimum horizontal principal stress, so it should be considered as an essential parameter for determining the in-situ stress regime around the rock mass. It shows usually an ambiguous value in pressure-time history curves, however, because of the relationship between the behavior of hydraulic fractures and the condition of remote stress regime. In this study, a series of numerical analyses have been carried out to compare several methods for determining the shut-in pressure during hydrofracturing. The hydraulic-mechanical coupling has been applied to numerical analysis for simulating the fracture propagation by hydraulic pressure, and the different discontinuity geometry has been considered in numerical models to examine the effect of numerical element shape on fracture propagation pattern. From the numerical simulations with the four different discontinuity geometries, it was revealed that the shut-in pressure obtained from graphical methods rather than statistical method was relatively small. Consequently a care should be taken in selecting a method for determining the shut-in pressure when a stress anomaly around borehole and a fracture propagation with complicate mechanism are considered.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.1
• /
• pp.1-17
• /
• 1982

The stream morphological characteristics of a river basin has a close correlation with the hydrological and hydraulic characteristics of the basin. In this study the correlations of flow duration and Hydraulic geometry with the stream morphological characteristics as well as the correlation between flow duration and hydraulic geometry were analyzed bases on the data for the Geum River basin. The purpose of this study was to provide the necessary informations for water utilization projects at ungauged locations along the river course. First of all, the stream morphological characteristics was analyzed based on the Horton's three laws on the morphology of a stream that is, the law of stream number, the law of average stream length and the law of average stream slope. As is the case for majority of the rivers it was found that the Geum River basin was well developed according to the Horton's laws. High correlations were also found between the basin characteristics and the channel characteristics. The flow duration curves obtained with the daily stream flow data of 10~90% frequency of occurences at the five stage gauging stations in the Geum River could, in general, be expressed as an exponential functional relationship. The concept of proportional stream ordering system was employed to describe continuously the longitudinal variation of the stream morphological characteristics, and the mathematical model was formulated for the discharge-frequency-proportional stream order relationship. With the morphological characteristics as a common parameter the relationships with flow duration, drainage area were established in mathematical expressions, respectively.

• Tunnel and Underground Space
• /
• v.32 no.3
• /
• pp.203-218
• /
• 2022

A hydro-mechanical study was performed to analyze the relationship between the magnitude of injection-induced seismicity and shut-in. In hydraulic analysis, the suspension of fluid injection makes the pore pressure gradient smaller while the pore pressure at the pressure front can reach the critical value for several hours after shut-in, which leads to the additional slip with wider area than during injection. The hydro-mechanical numerical analysis was performed to model the simplified fault system, and simulated the largest magnitude earthquake during shut-in stage. The effect of the abrupt suspension of fluid injection on the large magnitude earthquake was investigated in comparison with the continuous injection. In addition to the pore pressure distribution, it was found that the geometry of multiple faults and the stress redistribution are also important in evaluating the magnitude of the induced seismicity.