• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.41-47
• /
• 2018

This paper analyzes the output characteristics of a self excited induction generator with isolated mode according to change of its speeds and loads for building a hybrid electric propulsion system in special purpose ships by using power take off. The induction generators are being considered as an alternative choice to the well-developed generators because of their lower unit cost, inherent ruggedness, operational and maintenance simplicity. However, the generator working by stand alone has a few problems that the reactive power is required to establish the air gap magnetic flux, and the induced voltage and magnetizing current fluctuate when the load is varied. In spite of its advantages, basic design data of the capacitor bank and behaviors of the output characteristics of the generator are not sufficient for the system. Based on the operating condition(speed range of main engine) of the target boat, a reduced experimental equipment system was constructed to analyze the output characteristics of the SEIG. And a suitable capacitor bank of a stand-alone generator and its output characteristics under various loads was investigated in detail through these experiments. According to the experimental result, it was confirmed that the capacitor bank should be $70{\mu}F{\sim}100{\mu}F$, and the proper SEIG induced voltage should be DC 80 V ~ 250 V in order to storage electrical energy into a battery.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.216-223
• /
• 2012

The effect of water back-flushing period (FT) was investigated in hybrid process of carbon fiber microfiltration membrane and photocatalyst for advanced drinking water treatment in this study, and compared with the previous study using alumina ultrafiltration membrane. The FT was changed in the range of 2~10 min with fixed 10 sec of BT. Then, the FT effects on resistance of membrane fouling ($R_f$), permeate flux (J) and total permeate volume ($V_T$) were observed during total filtration time of 180 min. As decreasing FT, $R_f$ decreased and J increased, which was same with the previous result using alumina ultrafiltration membrane. The treatment efficiency of turbidity was high beyond 99.2%, and the effect of FT was not shown on treatment efficiency of turbidity, which was different with the previous result. The treatment efficiency of organic matters was the lowest value of 65.6% at NBF, and it increased as decreasing FT, which was different with the previous result, too. The reason was that the membrane fouling phenomena could show a different mechanism depending on ceramic membrane materials.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.3
• /
• pp.115-121
• /
• 2014

With increment on interesting about improving renewable energy efficiency, many research have been conducted and the research about hybrid air-water heater using solar energy that can make heating air and hot water has been conducted also. In this experiment, the temperature difference and thermal efficiency were investigated when two heating medium(air and liquid) was working simultaneously. As a result, thermal efficiency showed 44% to 88% when these heating medium was working simultaneously depending on operation condition and it is better than traditional solar collector. Also possibility of application into building equipment also was confirmed based on temperature and thermal efficiency. But necessity of additional studies about proper operation condition according to purpose of use and heat load was confirmed because change of thermal efficiency by air velocity and flux of liquid was shown a huge difference.

• Journal of Astronomy and Space Sciences
• /
• v.28 no.4
• /
• pp.267-271
• /
• 2011

I developed an enhanced correction method for Ricean bias which occurs in linear polarization measurement. Two known methods for Ricean bias correction are reviewed. In low signal-to-noise area, the method based on the mode of the equation gives better representation of the fractional polarization. But a caution should be given that the accurate estimation of noise level, i.e. ${\sigma}$ of the polarized flux, is important. The maximum likelihood method is better choice for high signal-to-noise area. I suggest a hybrid method which uses the mode of the equation at the low signal-to-noise area and takes the maximum likelihood method at the high signal-to-noise area. A modified correction coefficient for the mode solution is proposed. The impact on the depolarization measure analysis is discussed.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.233-234
• /
• 2011

본 논문에서는 IPMSM의 약자속 제어 영역에서 토크제어를 하기위한 전류제어기를 PI-IP 혼합제어기로 구성하였다. 약자속 제어 영역에서 토크제어 시 d축과 q축의 인덕턴스 차이로 인해 전류제어 응답의 차이가 발생하여 전압여유분 확보에 문제점이 발생한다. 이러한 문제점을 개선하고자 PI-IP 혼합제어기를 적용하여 약자속 영역에서의 d축과 q축의 전류 제어기의 응답특성을 달리하여 토크제어 시 과도상태에서 발생하는 문제점을 개선하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.2 s.245
• /
• pp.161-169
• /
• 2006

The spray characteristics of liquid jet in cross flow with variation of injection angle are numerically studied. Numerical analysis was carried out using KIVA code, which was modified to be suitable for simulating liquid jet ejected into cross flow. Wave model and Kelvin-Helmholtz(KH)/Rayleigh-Taylor(RT) hybrid model were used for the purpose of analyzing liquid column, ligament, and the breakup of droplet. Numerical results were compared with experimental data in order to verify the reliability of the physical model. Liquid jet penetration length, volume flux, droplet velocity profile and SMD were obtained. Penetration length increases as flow velocity decreases and injection velocity increases. From the bottom wall, the SMD increases as vertical distance increases. Also the SMD decreases as injection angle increases.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.8 no.2
• /
• pp.5-12
• /
• 2008

Since the past, an attempt of figuration which is for movement, time and force has existed constantly. A process of representative from expressed on the movement, time and force creates events, and the process through the events expresses the idea of a simulacre. Furthermore, Architectural works for potentiality to give a demonstration are in common with hybrid characteristics, and have lasting creation of flux architecture. Ignoring the gravity of the floating figuration, so it appears unrealistic hyperphysical virtual space that easily could make the life of creation. For this reason, the form generation based on the digital design method is expressed the important method. In conclusion, actualizing the virtual is the suitable way for 'devenir architecture' based upon the Deleuze Guattari's idea of 'simulacre' and creating the from generation on the contemporary digital architecture design in a similar way.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.318-324
• /
• 2004

In the recently, the necessity of linear position control motors have been increased in the various fields of the automatic control system. In this paper, we have designed the tooth models of the hybrid type linear stepping motor(HLSM); rectangular type(RT), triangle type(TrT), round type(RdT) and wedge type(WT), and proposed the optimum tooth shape of the HLSM by simulating(Flux2D) the thrust and normal force characteristics with the finite element method(FEM) and the virtual work method. And we have manufactured the prototype HLSM with the optimum tooth, and measured the various values by using experimental system. Thus, we have confirmed the justice of theory because the computed and the experimental results almost coincide with.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.584-587
• /
• 1992

Because linear motor directly drives linear motion, it does not need conversion equipment such as belt and gear. Especially linear pulse motor provide more precise positioning and large force of linear pulse motors. As current manufacture technic of linear pulse motor is much to be desired at home. This motor lay out to make use of computer aided design program, In this paper the experimental motor is 2-phases 4-poles hybrid pulse motor which has teeth per pole Simulation program is divided its function into 4 parts - air gap permeance analysis, permanent magnet & non-linear core operating point determine, winding configuration, leakage flux analysis. It is possible to make motor static and magnetic characteristics for this simulation program. Also, by varying input parameters of the program, experimental motor is to be compared to motor characteristics.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.766_767
• /
• 2009

Generally, the Doubly Salient Machine such as Switched Reluctance Motor doesn't have Permanent Magnet, it sometimes adopts permanent magnet or DC filed winding for high efficiency or adjustable speed control. In this paper, adjustable speed range is compared for Doubly Salient Permanent Magnet Machine (DSPM), Brushless Doubly Fed Doubly Salient Machine (BDFDS) and Hybrid Excited Doubly Salient Machine (HEDS). Especially, air-gap flux density to the DC field current is shown and the operating speed as the field-weakening is estimated.