• 대한기계학회논문집A
• /
• 제37권7호
• /
• pp.857-864
• /
• 2013

레이저 정밀 가공은 고품질의 집속 광에너지를 이용하여 재료를 미세하게 가공하는 특수 가공으로 정밀 제조 분야에 적용되고 있다. 그러나 레이저 가공 시 열적 효과로 인해 재료 특성을 저하 시킬 수 있다. 또한, 압연 강재 및 강판의 경우 공정 단계에서 강한 압력으로 제작하기 때문에 반드시 잔류응력이 존재한다. 하지만 압연 강재에 존재하는 잔류응력의 양은 정량적인 예측이 불가능하다. 이러한 잔류응력이 존재하는 재료의 레이저 가공 시 레이저에 의한 부가적인 응력 발생 및 재료에 미치는 열적 영향의 예측 및 평가는 정밀 가공에 있어서 반드시 고려해야 하는 사항이다. 본 연구에서는 레이저 홀 가공 시 발생되는 온도 및 응력을 유한요소 해석과 실험적 방법으로 분석하였다. 재료의 열응력을 예측하기 위해 레이저 홀가공 실험을 수행하여 가열 및 냉각 등의 대한 결과를 도출하였다. 또한 냉각 시간에 따른 응력의 변화를 파악하였고 유한요소 해석으로 예측된 응력을 홀드릴링 응력 측정 기법에 의해 도출된 응력과 비교 검증하였다.

• 한국추진공학회지
• /
• 제3권2호
• /
• pp.25-36
• /
• 1999

본 연구의 목적은 복합재 적층판의 드릴링작업시 양호한 구멍과 불량한 구멍의 제작에 관한 드릴링기술을 실험적으로 설명하며 복합재 적층판의 강도저하에 드릴링변수가 어떤 영향을 미치는지 조사하고 어떤 형태의 시험이 드릴링변수의 영향을 잘 보여주는지 알아보기 위한 것이다. 이를 위해 복합재 시편을 다섯가지 드릴링변수에 따라 드릴링작업하여 압축, 인장, 굽힘하중에 대한 실험을 수행하였다. 드릴링변수들이 시편의 구멍가공 품질에 중요한 영향을 미친다는 것을 알 수 있었고 빠른 스핀들 회전속도, 낮은 이송율, 잘 고정된 상태에서 드릴작업이 된 시편이 우수한 구멍가공 품질을 보여주었다. 굽힘실험결과가 구멍가공 품질에 대한 드릴링변수와 관련하여 가장 분명한 파괴강도를 보여주어 굽힘실험이 구멍 강도저하에 드릴링변수가 미치는 영향을 잘 나타내는 것을 알 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.105-108
• /
• 1995

So far,in deep drilling process there are several manufacturing problems such as hole deviation, hole over size, circularity,straightness and surface roughness. Whit regard to these problems, we atudied the abrasion process on carbided tip of BTA drill and got the follow test results through the abrasion characteristic test and analysis on cutting mechanism for the drill tooth and guide pad. 1) In SM55C drilling process, the most stable and reasonable drilling speed range for optmum abrasion characteristic of drill tooth was 60m.min. 2) The total drilling torque was about 60kg .deg.cm on condition drilling speed 60m/min and 0.15mm/rev. These results show that the theoretical burnising torque is well accord with the tested torque which is working on guide pad.

• 마이크로전자및패키징학회지
• /
• 제21권2호
• /
• pp.53-57
• /
• 2014

Thin glass (< 100 microns) is a promising material from which advanced interposers for high density electrical interconnects for 2.5D chip packaging can be produced. But thin glass is extremely brittle, so mechanical micromachining to create through glass vias (TGVs) is particularly challenging. In this article we show how laser processing using deep UV excimer lasers at a wavelength of 193 nm provides a viable solution capable of drilling dense patterns of TGVs with high hole counts. Based on mask illumination, this method supports parallel drilling of up over 1,000 through vias in 30 to $100{\mu}m$ thin glass sheets. (We also briefly discuss that ultrafast lasers are an excellent alternative for laser drilling of TGVs at lower pattern densities.) We present data showing that this process can deliver the requisite hole quality and can readily achieve future-proof TGV diameters as small $10{\mu}m$ together with a corresponding reduction in pitch size.

• 한국산업융합학회 논문집
• /
• 제25권4_2호
• /
• pp.603-609
• /
• 2022

Bottom hole assembly(BHA) is a key component of the drilling system, consisting of various components and tools(including the drill bit and mud motor) which operate at the bottom of the wellbore and physically drill the rock. This paper investigates the dynamic characteristics of the mud motor which is a drilling propulsion tool. And computational structural analysis is performed to calculate the von-Mises stress and the safety factor of components constituting the mud motor. In this process, the field test data of onshore drilling are used for analysis.

• 한국정밀공학회지
• /
• 제12권1호
• /
• pp.22-28
• /
• 1995

Micro Drills have found ever wider application. However micro drilling is a machining to integrate the difficult machinablities such as tool stiffness, position control and revolution accuracy, and is known to cost and time consuming. So, this study aimed to practice ultraminiature drilling(0.05 .phi. ) wiht simple component, if possible. System is developed as the three modules : feed drives, spindle and monitoring part. The dynamics of measured current signals from the spindle of Micro Hole Drilling machine are investigated to establish the criteria of stepfeed mechanism. Cutting experiments identify the relationship of spindle rpm, feed rate and tool life. The smaller drill diameter is, the more suitable cutting condition have to be selected because of chip packing.

• 한국전기전자재료학회논문지
• /
• 제29권12호
• /
• pp.786-790
• /
• 2016

Hole explosion behaviors were observed during drilling fine holes with laser beam on the LTCC green bar of $320{\mu}m$ thick after lamination of green sheets prepared by tape casting of thick film process. The incidence of these hole explosions was inversely proportional to hole sizes. The incidence of hole explosion was 20 % number of hole with the size of $60{\mu}m$ exploded for the UV radiation, while the explosion did not appear for hole sizes over $100{\mu}m$. To prevent hole explosion behavior during laser-drilling of fine holes, carbon black powder was added as an additive in the LTCC composition, which has superior thermal durability. As a consequence, hole explosion rate was suppressed to 0.8 % for the hole size of $50{\mu}m$ green sheet with the carbon black amount of 10 weight % and the laser power of 3 watt. Added carbon is thought to reduce the heat-affected region during laser drilling.

• 한국정밀공학회지
• /
• 제27권5호
• /
• pp.7-13
• /
• 2010

The integrity and accuracy of the drilling hole are decided by positional error, diameter error, the roundness, the straightness, the cylindericity, size of the burr, the surface roundness and others. Among these parameters, positional error and diameter error have the most important parameters. The diameter error has been widely studied, but there has been little research done about the positional error due to the difficulty of measuring it. The measurement of hole location and diameter would be performed by CMM(Coordinate Measurement Machine). However, the usage of CMM requires much time and cost. In order to overcome the difficulties, we have developed a hole location and diameter error measuring device using machine vision. The developed measurement device attached to a CNC machine can determine hole quality quickly and easily.

• 한국정밀공학회지
• /
• 제24권12호
• /
• pp.50-56
• /
• 2007

Femtosecond laser ablation of the Invar alloy and hole drilling for a shadow mask are studied. We used a regenerative amplified Ti-sapphire laser with a 1kHz repetition rate, 184fs pulse duration and 785nm wavelength. Femtosecond laser pulse was irradiated on the Invar alloy with air blowing at the condition of various laser peak power. An ablation characteristic of the Invar alloy was appeared non-linear at $125J/cm^2$ of energy fluence. For the application to a shadow mask, the hole drilling of the Invar alloy with the cross section of a trapezoidal shape was investigated. The ablated micro-holes were characterized using an atomic force microscopy(AFM). The optimal condition of hole pattern f3r a shadow mask was $4\;{\mu}m$ z-axis feed rate, 0.2mm/s circular velocity, $26.4{\mu}J$ laser peak power. With the optimal processing condition, the fine circular hole shape without burr and thermal damage was achieved. Using the femtoseocond laser system, it demonstrates excellent tool for the Invar alloy micro-hole drilling without heat effects and poor edge.

• Structural Engineering and Mechanics
• /
• 제69권5호
• /
• pp.537-545
• /
• 2019

Stress analysis of bottom-hole rock has to be considered with much care to further understand rock fragmentation mechanism and high penetration rate. This original study establishes a fully coupled simulation model and explores the effects of overburden pressure, horizontal in-situ stresses, drilling mud pressure, pore pressure and temperature on the stress distribution in bottom-hole rock. The research finds that in air drilling, as the well depth increases, the more easily the bottom-hole rock is to be broken. Moreover, the mud pressure has a great effect on the bottom-hole rock. The bigger the mud pressure is, the more difficult to break the bottom-hole rock is. Furthermore, the maximum principal stress of the bottom-hole increases as the mud pressure, well depth and temperature difference increase. The bottom-hole rock can be divided into three main regions according to the stress state, namely a) three directions tensile area, b) two directions compression areas and c) three directions compression area, which are classified as a) easy, b) normal and c) hard, respectively, for the corresponding fragmentation degree of difficulty. The main contribution of this paper is that it presents for the first time a thorough study of the effect of related factors, including stress distribution and temperature, on the bottom-hole rock fracture rather than the well wall, using a thermo-poroelastoplasticity model.