• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.85-88
• /
• 2001

Deep drawing process, one of sheet metal forming methods, is used widely. Circular or square shape blanks are currently studied mainly. Especially, circular blank for coating case of chip condenser remains bridges when it is made out of aluminum coil. The bridge reduces Material-withdrawal-rate of aluminum coil to $60\%$. This paper proposes a no-bridge blank instead of circular blank. To get the different values of two cases, comparison circular blank with no-bridge blank is accomplished in the point of thickness strain in the vicinity of flange. In order to find optimal condition in new proposed blank, several process variables - those are blank holder shape, die shape radii, punch shape radii and blank holding force - are changed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.90-95
• /
• 2007

In order to investigate the optimum condition of the autofrettage process for the diesel engine injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was preformed by applying the hydrostatic internal pressures of 603 MPa, 535 MPa, 500 MPa on the fuel injection pipe, corresponding to theoretically 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeating application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.276-284
• /
• 1993

The interfacial phenomena between intermetallic compounds and Al matrix have been studied at $680^{\circ}C$ for various holding time under argon atmosphere. Model experiments were performed using Fe, Ni and Ti wire to observe the interfacial phenomena. The interfacial phenomena between intermetallic compounds and Al matrix were analysed by optical microscope, SEM and EDX. The results of EDX and XRD showed that the interfacial zones of intermetallic compounds/Al matrix were composed of several intermetallic layers. The reaction layer was varied with holding time and heating temperature. The investigation of interfacial zones in the specimen as a function of heat treatment time at $680^{\circ}C$ indicated that the best heat treatment condition for squeeze casting was $680^{\circ}C$ for 5min.

• 소성∙가공
• /
• 제19권5호
• /
• pp.296-304
• /
• 2010

It is still needed to study the effect of process conditions on the final properties of injection-molded parts for producing precision optical products. Especially, the optical anisotropy, i.e., birefringence, is a significant factor to affect the function of many optical components. In the present study we have focused on the effect of holding and compression processes on the birefringence remaining in the transparent disc by examining the gap-wise distribution of birefringence and extinction angle. As a result, two extra birefringence and extinction peaks near the center in thickness direction showed the effect of holding pressure, which came from the flow in packing stage. However, more uniform birefringence distribution than injection-only cases could be found in injection/compression cases. Depends on the process condition even the flow reversal could be found from the distribution of extinction angle. Finally, graphical representation of optical indicatrix was added for better understanding the final structure of injection-only and injection/compression cases.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 추계학술대회 논문집
• /
• pp.80-94
• /
• 1994

As for axisymmetirc sheet metal forming, a kind of pick-up apparatus for body-wrinkling is deviced. Experiments with both hemispherical and flat headed punches, with various clearances between punch and die, with respect to three kinds of materials each of which has two thicknesses, are performed. Firstly the process of evolution of body-wrinkling is observed. Then the critical blank-holding force (or meridional tensile force) for suppression of body-wrinkling at a specified punch-stroke is measured for all cases mentioned above. An empirical formula for it is proposed. Deformation patterns and stress distributions are analysed by the use of FEM. A simplified critical condition for body-wrinkling is formulated and introduced into the FEM program. And its effectiveness is checked by comparison with the experimental results. Using this FEM system, the governing factors of body-wrinkling are cleared up.

• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.106-113
• /
• 2000

This study describes how a properly calibrated simulation method could be used to investigate the latchup immunity characteristics among the various high energy ion implanted CMOS twin well (retro-grade/BILLI/BL) structures. To obtain the accurate quantitative simulation analysis of retrograde well, a global tuning procedure and a set of grid specifications for simulation accuracy and computational efficiency are carried out. The latchup characteristics of BILLI and BL structures are well predicted by applying a calibrated simulation method for retrograde well. By exploring the potential contour, current flow lines, and electron/hole current densities at the holding condition, we have observed that the holding voltage of BL structure is more sensitive to the well design rule (p+to well edge space /n +to well edge space) than to the retrograde well itself.

• 펄프종이기술
• /
• 제39권3호
• /
• pp.77-83
• /
• 2007

This study was carried out to examine the optimum culture condition for the production of cellulose from Saprolegnia ferax and its physical characteristics. Conclusions obtained from the results of this study were as follows: In producing the cellulose from S. ferex, optimal pH and temperature were 7.0 and $26{\sim}30^{\circ}C$ with a maximum of $26^{\circ}C$, respectively. And, optimal culture period was 11days. WHC and OHC of biocellulose were 3.2(25.04 g/g) times and 3.5(25.75 g/g) times higher than those of commercial ${\alpha}-cellulose$(7.57, 7.25 g/g) respectively. The viscosity of biocellulose is lower than that of commercial ${\alpha}-cellulose$. And the effect of rpm on the viscosity of biocellulose was more than on the that of ${\alpha}-cellulose$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.164-164
• /
• 2010

Cds films were deposited on glass substrates using rf magnetron sputtering method followed by rapid thermal annealing(RTA). Effects of annealing temperature on surface characteristic, structural, electrical and optical property of CdS films were investigated at different temperatures ranging from 250 to $550^{\circ}C$ with various holding time. The film annealed at $450^{\circ}C$ with less than 1 min holding time is attributed to the improved crystalline quality of CdS film due to the effective relaxation of residual compressive stress and achieving maximum grain size. The results show that RTA treatments under optimal annealing condition can provide significant improvements in the properties of CdS films.

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1649-1657
• /
• 2010

성형조건에 따른 GFRP 복합재료를 관찰하여, 성형품 표면의 불량원인을 조사했다. 표면거칠기에 영향을 주는 요철의 가장 주요한 발생원인은 보압 냉각 과정에서 발생하는 모재의 수축이었다. GFRP 복합재료 성형품 표면은 성형 시의 보압하중이 높을수록 좋아졌고, 서냉실험에서는 탈형온도가 낮을수록 성형품의 표면이 좋아졌다. 그리고 보압하중과 탈형온도를 고려하여, 성형품의 표면요철 생성과정과 섬유돌출 높이 변화를 규명했다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.71-74
• /
• 2001

Using the Taguchi method, optimum process condition of lead frame blanking has been determined in the point of view of shape of blanked profile. As the main process parameters, clearance, strip holding pressure and bridge width are selected. According to the orthogonal array table, three levels of experiment have been carried out for each factors. The optimal blanking condition is analyzed with the SN ratio. It has been verified that the optimal process condition can be determined with a combination of basic blanking experiment and experiment design method. Both the effect of each factors and gain can be judged in the quantitative manners from the analysis of SN ratio.