1 |
E. Lee, T. Rogers and T. Woo, 1965. “Residual
Stresses in a Glass Plate Cooled Symmetrically
from Both Surfaces”, J. of the American Ceramic
Society. Vol. 48, P. 480.
DOI
|
2 |
T. H. Lin, 2009, “Birefringence, Anisotropic
Shringkage and Luminance in Injection Molded
Light-Guide plate; Modeling and experiment”,
Dissertation, U. of Akron.
|
3 |
I. K. Min, J. S. Kim, Y. B. Ko, H. P. Park and K. H.
Yoon, C. J. Hwang, 2006, "An Experimental Study
on The Improvement of Pattern Replication and
Birefringence in LGP by Adding Compression
Effects", Trans. of Materials Processing, Vol.15, No.
1, pp. 27-33.
DOI
|
4 |
S. J. Yu and K. H. Yoon, 1995, "Development of a
Presentation Technique for the Birefringence Data
in Injection-Molded Articles by Using an Optical
Indicatrix", KSME Autumn Conference, pp.
886-891
|
5 |
Hecht, E, 1987, Optics. Berlin, Massachusetts, Addison-Wesley
|
6 |
H. Janeschiz-Kriegl, 1983, “Polymer Melt Rheology
and Flow Birefringence”, Berlin, Springer Verlag.
|
7 |
J. S. Kim, K. H. Yoon, 2004, "One Image Analysis
for 2-D Birefringence Measurements by Chromatic
Aberration", KSME Spring Conference, pp.
1761-1766.
과학기술학회마을
|
8 |
C. J. Wust and D. C. Bogue, 1983. “Stress Optical
Behavior in Polystyrene; Residual Stresses and
Birefringence in Large, Quenched Samples”, J. of
Applied Polymer Science. Vol. 28, PP. 1931-1947.
DOI
|
9 |
H. S. Lee and A. I. Isayev, 2007, “Numerical
Simulation of Flow-Induced Birefringence:
Comparison of Injection and Injection/Compression
Molding” Inter. J. of Precision Eng. And
Manufacturing, Vol. 8, No. 1, pp. 66-72.
|
10 |
Y. B. Lee, T. H. Kwon and K. H. Yoon, 2002,
"Numerical Prediction of Residual Stresses and
Birefringence in Injection/Compression Molded
Center-Gated Disk. Part II: E", Polym. Eng. Sci, Vol.
42, No. 11, pp. 2273-2292.
DOI
|
11 |
W. B. Young, “Effect of Process Parameters on
Injection Compression Molding of Pickup Lens”,
2005, Applied Mathematical Modelling, Vol. 29, pp.
955-971.
DOI
|
12 |
C. H. Wu and W. S. Chen, 2006, “Injection Molding
and Injection/Compression Molding of Three-beam
Grating of DVD Pickup Lens” Sensors and
Actuators A, Vol. 125, pp. 367-375.
DOI
ScienceOn
|
13 |
Y. B. Lee, T. H. Kwon and K. H. Yoon, 2002,
"Numerical Prediction of Residual Stresses and
Birefringence in Injection/Compression Molded
Center-Gated Disk. Part I: Basic Modeling and
Results for Injection Molding", Polym. Eng. Sci,
Vol. 42, No. 11, pp. 2246-2272.
DOI
|
14 |
A. I. Isayev, 1987, “Injection and Compression
Molding Fundamentals”, New York and Basel.
Marcel Dekker. INC.
|
15 |
A. I. Isayev and C. A. Hieber, 1980, "Toward a
Viscoelastic Modelling of the Injection Molding of
Polymers", Rheol. Acta Vol. 19, pp. 168-182.
DOI
|