• Progress in Superconductivity and Cryogenics
• /
• v.25 no.1
• /
• pp.16-20
• /
• 2023

The International Electrotechnical Commission (IEC) 61788-26:2020 provides guidelines for measuring the critical current of Rare-earth barium copper oxide (REBCO) tapes using two methods: linear ramp and step-hold methods. The critical current measurement criterion, 1 or 0.1 μV/cm of electric field from IEC 61788-26 has been normally applied to REBCO coils or magnets. No-insulation (NI) winding technique has many advantages in aspects of electrical and thermal stability and mechanical integrity. However, the leak current from the NI REBCO coil can cause distortion in critical current measurement due to the characteristic resistance which causes the radial current flow paths. In this paper, we simulated the NI REBCO coil by applying both linear ramp and step-hold methods based on a simplified equivalent circuit model. Using the circuit analysis, we analyzed and evaluated both methods. By using the equivalent circuit model, we can evaluate the critical current of the NI REBCO coil, resulting in an estimation error within 0.1%. We also evaluate the accuracy of critical current measurement using both the linear ramp and step-hold methods. The accuracy of the linear ramp method is influenced by the inductive voltage, whereas the accuracy of the step-hold method depends on the duration of the hold-time. An adequate hold time, typically 5 to 10 times the time constant (τ), makes the step-hold method more accurate than the linear ramp method.

• Nuclear Engineering and Technology
• /
• v.55 no.9
• /
• pp.3252-3259
• /
• 2023

The influence of hold-down spring (HDS) on the vibration characteristics of core barrel is studied in this paper. First, the vibration characteristics experiment of core barrel was carried out with four type of different hold-down spring. These hold-down springs represent the same hold-down force under different spring stiffness and different hold-down force under the same spring stiffness. And then a new finite element method for researching the influence of hold-down spring on the vibration characteristics of core barrel was presented. This new method could consider the influence of the hold-down force and the spring stiffness at the same time. The results suggest that, the hold-down force and friction have greater influence on the vibration characteristics of core barrel than the spring stiffness, and the influence is nonlinear. The influence of the boundary condition on beam mode is greater than that on shell mode for core barrel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.1-12
• /
• 1995

Isothermal and thermal-mechanical fatigue characteristics of 12Cr heat resisting steel used for high temperature applications were investigated including hold time effects. Isothermal low cycle fatigue test at $600^{\circ}C$ and in-phase, out-of-phase thermal-mechanical fatigue test at 350 to $600^{\circ}C$ were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. Regardless of thermal-mechanical and isothermal fatigue tests, cyclic softening behavior was observed and much more pronounced in the thermal-mechanical fatigue tests with hold times due to the stress relaxation during the hold time. The phase difference between temperature and strain in thermal-mechanical fatigue tests resulted in significantly shorter fatigue life for out-of-phase compared to in-phase. The differences in fatigue lives were dependent upon the magnitudes of plastic strain ranges and mean stresses. During the hold time in the strain-controlled fatigue tests, the increase in the plastic strain range and the stress relaxation were observed. It appeared that the increase in plastic strain range per cycle and the introduction of creep damage made important contributions to the reduction of thermal-mechanical fatigue life with hold time, and the life reduction tendency was more remarkable in the in-phase than in the out-of-phase thermal-mechanical fatigue. Isothermal fatigue tests performed under the combination of fast and slow strain rates at $600^{\circ}C$ showed that the fatigue life decreased as the strain rate and frequency decreased,especially for the low strain ranges.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.593-596
• /
• 1997

This paper is concerned with the properties of zeros of discrete-time systems which are composed of a hold, a continuous-time plant and a sampler in cascade. Here the signal reconstruction is based on the fractional order hold. In order to overcome the implementing problem of the fractional order hold, the piecewise constant reconstruction method by use of the zero order hold is introduced. The properties of the zeros are explored in the limiting cases when the sampling period tends to zero. The stability conditions of the zeros for sufficiently small sampling periods are also presented.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.8
• /
• pp.883-890
• /
• 2015

As the semiconductor processing technology has been developing, multiple cores or NoC(network on chip) can be contained in recent chips. GALS(globally asychronous locally synchronous) clocking scheme that has multi-clock domains with different frequencies or phase differences is widely used to solve power consumption and clock skew in a large chip with a single clock. A synchronizer is needed to avoid a synchronization problem between sender and receiver in GALS. In this paper, the setup and hold time of DFF required to design the synchronizer are measured using 180nm CMOS processing parameters depending on temperature, supply voltage, and the size of inverter in DFF. The simulation results based on the bisection method in HSPICE show that the setup and hold time are proportional to temperature, however they are inversely proportional to supply voltage, and negative values are measured for the hold time.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.301-302
• /
• 2016

Hold-up time 조건에 의해 넓은 입력전압 범위에서 설계되는 하프-브리지 LLC 컨버터는 높은 전압 이득을 얻기 위해 작은 자화 인덕턴스와 넓은 스위칭 주파수 범위가 요구된다. 하지만 이는 큰 1차측 도통손실 및 코어 손실을 초래한다. 본 논문에서는 하프-브리지 LLC 컨버터가 좁은 입력전압에서 설계되기 위한 새로운 hold-up time 보상 기법을 제안한다. 따라서 제안된 기법에서의 하프-브리지 LLC 컨버터는 큰 자화 인덕턴스 및 좁은 스위칭 주파수 범위로 설계 될 수 있다. 제안된 회로의 효과는 90-264Vrms 입력, 250-400V 링크 전압, 48V/480W 출력을 갖는 prototype의 실험을 통해 검증된다.

• Journal of the Korean Society of Safety
• /
• v.18 no.1
• /
• pp.38-43
• /
• 2003

In this paper, the low cycle fatigue(LCF) life tests were carried out under waveforms of asymmetric triangle($4{\times}10^{-3}$ and $4{\times}10^{-10}$ strain rate) and hold-time(1min and 10min) in strain control. In triangular waveform, the fatigue lives of fast-slow waveforms were decreased to about 63-73% and them of slow-fast waveforms were down to about 23-24% compared to them of fast-fast waveforms. The shapes of fracture surfaces were transgranular in fast-fast and fast-slow waveforms and intergranular in slow-fast ones. The fatigue lives of slow-fast waveforms were remarkedly shorter than them of hold-time waveforms even though cycle times of hold time waveforms were longer than them of slow-fast ones. The damage mechanisms of frature surfaces were mixed frature with both transgranular and intergranular, but intergranular fratures were r-type cavity in hold-time waveforms and w-type cavity in slow-fast ones.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.382-384
• /
• 2008

Hold-up time is a special requirement for the front end DC/DC converter in a server power supply. It forces the converter with the variable switching frequency to operate in a wide switching frequency range, which makes the regulation difficult and reduces the power density. In this paper a novel frequency controlled half bridge converter with the hold-up time extension circuit is proposed. During the hold-up time, the auxiliary switches are turned on, thus the resonant inductance is reduced and the voltage conversion ratio is increased. Therefore, the output capacitor of the power factor correction (PFC) circuit can be decreased, and the converter can have high power density. The proposed converter is verified by experimental results from a prototype with 700W, 400V input, and 12V output.

• Journal of ILASS-Korea
• /
• v.21 no.3
• /
• pp.155-161
• /
• 2016

Injected fuel pressure waves of a common rail injector with various current profiles supplied to the injecor were measured using Bosch method. In order to drive the common rail injector, the current in the solenoid should be controlled using what is known as a peak and hold pattern, which consists of a high current level with a short time duration (peak) in the first step and a low current level with a long time duration (hold) in the subsequent step. The current profile can be shaped by swithcing an injector driving power source with the peak and hold waves. The capture, compare and PWM (CCP) pin in the microprocessor was used to generate the combined peak and hold waves. The PWM square wave generated from the CCP pin has a duty ratio of 100% for the peak current and 10% or 30% for the hold pattern. Five patterns of the current profile were generated by combining the peak and hold wave. The common rail pressure is controlled at 75, 100, and 130 MPa. As the fuel rail pressure increases, the variations of the measured fuel injection pressure wave according to the current profiles decrease.

• Physical Therapy Korea
• /
• v.7 no.1
• /
• pp.22-31
• /
• 2000

Despite research to treat delayed onset muscle soreness (DOMS), no effective treatment has been reported. The purpose of this study is to investigate the effect of a hold-relax technique and cryotherapy on DOMS. Thirty-three subjects were randomly assigned to one of three treatment groups: control, hold-relax technique, or hold-relax technique and cryotherapy. DOMS was induced in the non-dominant biceps muscle through repeated eccentric contractions. Resting elbow joint position, flexion and extension (universal goniometer), pain (Visual Analogue Scale; VAS), and WBC count (blood analysis) were measured one hour before DOMS was induced and 24, 48, and 72 hours after DOMS was induced. The data were analyzed by repeated measure of two-way ANOVA. The results of this study were summarized as follows: 1) While analysis showed no significant differences between groups in relation to a resting elbow joint position, there were significant differences over time, especially at 24, 48 hours after DOMS was induced compared with resting elbow joint position before DOMS was induced. 2) While analysis showed no significant differences between groups in relation to range of flexion, there were significant differences between range of flexion before DOMS was induced and range of flexion 72 hours after DOMS was induced. 3) There were no significant differences between groups or over time in relation to range of extension. 4) While analysis showed no significant differences between groups in relation to VAS, there were significant differences over time in different hours. 5) There were no significant differences between groups or over time in relation to WBC count. 6) There were no interactions between groups or over time in all variables. This results suggested that hold-relax technique and cryotherapy were not effective to reduce DOMS.