• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.57-68
• /
• 2005

Vehicle classification system in Korea is operated by two different types depending on operating purpose and place. 8-category classification system operates in Expressway and Provincial road, and 11-category classification system operates in National highway. These different operations decrease the efficiency of practical use of gathering data. Therefore, this study proposes new-modified vehicle classification system for solving this problem. For classification, this study not only focuses on mechanic survey system which is based on vehicle specs, it's also focuses on the applicability of roadside survey. This proposed classification system considers the tendency to vary of vehicle types, and the compatibility with the other classification systems. This system might be the most suitable system for our present situation.

• Geophysics and Geophysical Exploration
• /
• v.7 no.1
• /
• pp.80-87
• /
• 2004

During excavation work for the construction of a highway bridge in a limestone area in Korea, several cavities were found, and construction work was stopped temporarily. Cavities under the bridge piers might seriously threaten the safety of the planned bridge, because they could lead to excessive subsidence and differential settlement of the pier foundations. In order to establish a method for reinforcement of the pier foundations, borehole radar reflection and tomography surveys were carried out, to locate cavities under the planned pier locations and to determine their sizes where they exist. Since travel time data from the crosshole radar survey showed anisotropy, we applied an anisotropic tomography inversion algorithm assuming heterogeneous elliptic anisotropy, in order to reconstruct three kinds of tomograms: tomograms of maximum and minimum velocities, and of the direction of the symmetry axis. The distribution of maximum velocity matched core logging results better than that of the minimum velocity. The degree of anisotropy, defined by the normalized difference between maximum and minimum velocities, was helpful in deciding whether an anomalous zone in a tomogram was a cavity or not. By careful examination of borehole radar reflection and tomography images, the spatial distributions of cavities were delineated, and most of them were interpreted as being filled with clay and/or water. All the interpretation results implied that two faults imaged clearly by a DC resistivity survey were among the most important factors controlling the groundwater movement in the survey area, and therefore were closely related to the development of cavities. The method of reinforcement of the pier foundations was based on the interpretation results, and the results were confirmed when construction work was resumed.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.37-44
• /
• 2009

Currently the reasonability of threshold values for rutting and cracking does not clearly defined at the Pavement Rehabilitation Decision Tree on national highway PMS(Pavement Management System). The goal of this study is to provide the reasonable threshold values for the national highway asphalt concrete pavement rehabilitation. To achieve this goal, test section that represents typical asphalt concrete pavement of national highway was selected and pavement export were participated. Pavement condition survey has been conducted and pavement performance data at the selected roadway section were analyzed. From this study, reasonable threshold values of Pavement Rehabilitation Decision Tree were suggested based on the pavement expert's engineering judgement. In terms of crack repairs, the application of overlay after cutting is required to deteriorated area where existing crack ratio is over 35% and just overlay is required to where crack ratio is over 20%. On rutting, rut depth over 13mm is required to overlay after cutting and rut depth over 10mm is just needed to overlay.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.729-735
• /
• 2016

According to the survey for working environment of the cashiers in highway tollbooths, workers replied that noise was the most harmful substances next to air pollutant in the tollbooth. Researches on the noise levels exposed to cashiers in the highway tollbooth scarcely have been performed. Therefore, the aim of this study was to acquire baseline data to prevent health impairments of the cashiers by evaluating noise level exposed to them. Noise dosimeters were used for monitoring workers' noise exposure level in the tollbooths at 8 different highway tollgates. The noise levels of tollbooths did not exceed noise exposure limit of the ministry of labor, 90 dB(A). The average TWA inside of the tollbooths was 55.4 dB(A) and the average TWA outside of tollbooths was 58.3 dB(A). The average TWA outside of tollbooths was slightly higher than that of inside of tollbooths. However, the significance probability(p-value) was 0.255 which means statistically not significant. The noise levels inside and outside of tollbooth were statistically significant to both mean traffic volume per day and traffic volume of passenger car.

• Journal of Korean Society of Transportation
• /
• v.20 no.1
• /
• pp.131-139
• /
• 2002

This study introduces a developed artificial neural networks(ANN) model as a more efficient and reliable prediction model in operating speed Prediction with the 85th percentile horizontal curve of two-way rural highway in the aspect of evaluating highway design consistency. On the assumption that the speed is decided by highway geometry features, total 30 survey sites were selected. Data include currie radius, curve length, intersection angle, sight distance, lane width, and lane of those sites and were used as input layer data of the ANN. The optimized model structure was drawn by number of unit of hidden layer, learning coefficient, momentum coefficient, and change in learning frequency in multi-layer a ANN model. To verify learning Performance of ANN, 30 survey sites were selected while data in obtained from the 20 cites were used as learning data and those from the remaining 10 sites were used as predictive data. As a result of statistical verification, the model D of 4 types of ANN was evaluated as the most similar model to the actual operating speed value: R2 was 85% and %RMSE was 0.0204.

• International Journal of Highway Engineering
• /
• v.15 no.1
• /
• pp.143-154
• /
• 2013

PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

• Journal of Information Technology Services
• /
• v.20 no.1
• /
• pp.81-92
• /
• 2021

As the degree of economic development of society increases, the maintenance issues on the existing social overhead capital becomes essential. Accordingly, the adaptation of the concept of Level of service in highway maintenance is indispensable. It is also crucial to manage and perform the service level such as road assets to provide universal services to users. In this regards, the purpose of this study is to improve the maintenance service rating model and to focus on the assessment items and weights among the improvements. Particularly, in determining weights, an Analytic Hierarchy Process (AHP) is performed based on the survey response results. After then, this study conducts unsupervised neural network models such as Self-Organizing Map (SOM) and Davies-Bouldin (DB) Index to divide proper sub-groups and determine priorities. This paper identifies similar cases by grouping the results of the responses based on the similarity of the survey responses. This can effectively support decision making in general situations where many evaluation factors need to be considered at once, resulting in reasonable policy decisions. It is the process of using advanced technology to find optimized management methods for maintenance.

• Earthquakes and Structures
• /
• v.26 no.3
• /
• pp.229-237
• /
• 2024

This paper studied the subgrade spring stiffness and its influencing factors in the seismic deformation method of circular tunnel. Numerical calculations are performed for 3 influencing factors: stratum stiffness, tunnel diameter and burial depth. The results show that the stratum stiffness and tunnel diameter have great influence on the subgrade spring stiffness. The subgrade spring stiffness increases linearly with stratum stiffness increasement, and decreases with the tunnel diameter increasement. When the burial depth ratio (burial depth/tunnel diameter) exceeds to 5, the subgrade spring stiffness has little sensitivity to the burial depth. Then, a proposed formula of subgrade spring stiffness for the seismic deformation method of circular tunnel is proposed. Meanwhile, the internal force results of the seismic deformation method are larger than that of the dynamic time history method, but the internal force distributions of the two methods are consistent, that is, the structure exhibits elliptical deformation with the largest internal force at the conjugate 45° position of the circular tunnel. Therefore, the seismic deformation method based on the proposed formula can effectively reflect the deformation and internal force characteristics of the tunnel and has good applicability in engineering practice.

• International Journal of Highway Engineering
• /
• v.15 no.3
• /
• pp.127-135
• /
• 2013

PURPOSES : The purpose of this study is development of automatic equipment to measure the road water-reservoir which can be one of factors for road traffic safety inspection and its application to safety analysis. METHODS : The scopes of this study are the examination of the riskiness and location of road water-reservoir through literature review, development of appropriate sensor and automatic equipment to survey the road water-reservoir and evaluation of field application. RESULTS: The laser lighting and IR camera were selected to develop the equipment. It was found from the field calibration that there is a high correlation between rutting and road water-reservoir and road water-reservoir caused by rutting can be correctly calculated. About 20.2km of national highway were inspected for case study and field application. It was found from correlation of traffic incident that 2.08km of the latent length for water-reservoir which is related to 12 traffic incidents were analyzed. CONCLUSIONS : This technique can be utilized evaluation method for road condition such as road water-reservoir for conventional evaluation system such as road traffic safety assessment and safety analysis and it can be use to new evaluation system to apply various road condition and traffic condition.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.3
• /
• pp.341-347
• /
• 2007

For the purpose of finding how aircraft noise annoyance response is affected by variables when noise survey is performed, the questionnaire survey is conducted around the Gimpo International Airport in Seoul, Republic of Korea. This residential area is exposed to the aircraft noise and road traffic noise, simultaneously. Research areas are classified according to three different aircraft noise exposure levels expressed in WECPNL, under 75, between 75 and 80, and above 80 WECPNL, on aircraft noise map. The 7-step numerical magnitude with verbal category scales is used to measure the annoyance level. This survey suggests that aircraft noise annoyance is not affected to an important extent by other noise sources(road traffic noise, community noise) and demographic variables(sex, age, education, occupation, dwelling type, length of residence).