• Food Science of Animal Resources
• /
• v.31 no.5
• /
• pp.641-648
• /
• 2011

This study investigated the effects of high pressure with or without thermal treatment on the cured color development and residual nitrite contents of model meat systems (pork, NaCl and sodium nitrite). At low nitrite levels (${\leq}50{\mu}g/g$), 200 MPa of pressure alone (P) did not develop the cured meat color (p>0.05). Thermal treatment (T) showed curing pigmentation (higher CIE L* and CIE a*), and the impacts were more effective when pressure was combined with thermal treatment (PT). In contrast, nitrite levels did not contribute to the cured meat color when ${\geq}200{\mu}g/g$ of nitrite was added to the meat. At high nitrite levels, although the typical cured color that is induced by thermal treatment did not present by pressure alone, the PT treatment still showed a pinker color with low residual nitrite content compared to the T treatment. The higher the pressure level (300 MPa), the greater the cured meat pigmentation with lower residual nitrite. Therefore, the present study demonstrates the possible application of high pressure, both for cured pigmentation and reducing residual nitrite, respective to typical thermal treatments.

• Food Science and Biotechnology
• /
• v.14 no.6
• /
• pp.808-812
• /
• 2005

The effects of high pressure processing, pressure level (50, 100, 150, and 200 MPa) and pressurized time (0, 5, 10, 15, 30, 45, and 60 min) on the physico-chemical properties of pork M. longissimus dorsi were evaluated. The pH value was affected by both pressure level and pressurized time, especially at 200 MPa (P<0.05). In color measurement, $L^*$ and $a^*$-values were increased by both pressure level and pressurized time, but $b^*$-value did not differ significantly (P>0.05). Water holding capacity (WHC) was significantly decreased (P<0.05) depending on pressure level and pressurized time, while cooking loss was gradually increased. Warner-Bratzler shear force did not differ significantly (P>0.05) among the treatments. These results indicate that high pressure processing below 200 MPa for 1 hr had no effect on the quality of cooked meat, although some alterations were observed before cooking.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.102-109
• /
• 1994

As a fundamental study to apply high pressure injection system to direct injection diesel engine, fuel injection system and constant volume combustion chamber were made and the behaviors of evaporating spray with the variation of injection pressure and the ambient gas temperature were observed by using high speed camera, and the combusion characteristics with the variation of injection pressure and A/F ratio were analyzed. As injection pressure increases, spray tip penetration and spray angle increase and, as a results spray volume increases. This helps an uniform mixing of fuel and air. Spray liquid core length decreases as ambient gas temperature increases, while it decreases as injection pressure increases but the effect of ambient gas temperature is dorminant. As injection pressure increases, ignition delay is shortened and combustion rate being raised, maximum heat release rate increases. It become clear that High injection pressure has high level of potential to improve the performance of DI-diesel engine.

• Journal of environmental and Sanitary engineering
• /
• v.22 no.1 s.63
• /
• pp.67-74
• /
• 2007

The purpose of this study is to provide the necessarily basic data of the ideal growth of the students by investigating the effect of the student's stress due to the parent's achievement pressure. The sample of this study are In students consisting of 51 boys and 49 girls in the 3rd grade classes of "J" middle school located in Siheung city, Kyungki-do. The observed materials are used to investigate the parent's achievement pressure and the level of stress. Based on the observed data, the frequency, correlation, and t-test have been gained. The results are summarized as follows : 1. The perception of the parent's achievement pressure is shown more by the boy's achievement pressure($44.2{\pm}9.9$) than the girl's achievement pressure($39.939{\pm}11.089$), among the high level students. 2. The perception of the parent's achievement pressure is shown more the high($43.0{\pm}10.7$) and middle($42.9{\pm}11.8$) level students than the low($39.7{\pm}8.00$) level students. 3. The stress of male students was high in the Solving Problem stress factor with by the mean of $15.1{\pm}3.7$, and the stress of female students was high in the Self-Control stress factor with the mean of $13.3{\pm}3.9$. 4. The stress of high, middle, low level student was high in the Solution of Matter stress factor with the mean of $14.2{\pm}3.9$. 5. The results were the main cause of the stress than the parent's achievement pressure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.3
• /
• pp.122-129
• /
• 2016

In this study, we developed a pressing device which can reproduce the pressure of concrete inside the conveying pipe as a part of the basic study to development of high fluidity concrete under high pressure pumping. Using this pressing device, we evaluated a absorption properties of aggregate that are crushed coarse aggregate, river gravel and lightweight coarse aggregate according to pressure of coarse aggregate and aggregate inside a high fluidity concrete, focused on the reduction of unit water quantity by pressure. In addition, it was evaluated the compressive strength of high fluidity concrete about before and after of pressive. Test a result, case of condition under the high pressure of 250 bar, absorption ratio of crushed coarse aggregate and river gravel were not increased above the surface absorption, absorption ratio of lightweight coarse aggregate was increased than the surface absorption.

• Journal of ILASS-Korea
• /
• v.4 no.1
• /
• pp.34-44
• /
• 1999

The purposes of this study were to evaluate engine performance and to analyze smoke emission characteristics for varied injection pressures and engine operating conditions of an electronically-controlled ultra high pressure fuel injection system(UHPFIS). It was discovered that the engine performance with the present UHPFIS was far better than what was initially expected. And the UHPFIS permitted engine operation at air/fuel ratios richer than 20 : 1 without increasing smoke emissions. It was discovered that the indicated mean effective pressure was increased, while the specific fuel consumption and the amount of soot were decreased, as the fuel rail pressures were improved atomization of the fuel spray. As the intake air temperature was increased from $38\sim205^{\circ}C$ in 38 degree increments, the indicated mean effective pressure was dropped while the specific fuel consumption was increased.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.159-162
• /
• 2008

High pressure is involved during injection molding operation specially packing phase. Cracks in the mold are often occurred by high cavity pressure. In this study, structural analysis of mold has been performed using commercial softwares, Abaqus and Ansys, to investigate cause of crack in the injection mold. Structural analysis contains four cases: stress distribution according to the cavity pressure, stress concentration according to the boundary conditions, stress concentration for inter-locking design of mold, and stress concentration for distributed cavity pressure. Through this study it was observed that the locations of stress concentrations were coincident with locations of crack. Robust mold design is being required to withstand high cavity pressure.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.83-89
• /
• 2006

Recently, the seriousness of high blood pressure was appeared as the most frequent disease of a the whole sickness in the world. However, the treatment of this disease is uncertain and produces an adverse reaction of a medicine therapy. Also, the patients are burdened with a fee for medical treatment. Therefore, in this paper, we studied effectively and financially to execute the treatment of high blood pressure using the Chinese medicine theorem that is recently arousing the great interest of the people. The main theories in this paper are blood vessel theory and acupuncture, respectively. Especially, the composed circuit systems are classified the blood pressure depressor part and the meridian points discrimination part, respectively. The blood pressure depressor part is composed generally of low-frequency generation circuit, charging-discharging circuit, and micro-computer circuit. Finally, this research have the advantage of discrimination parts such as regular voltage generating circuit, stimulus circuit, amplifying circuit, and alarm circuit.

• Fire Science and Engineering
• /
• v.27 no.1
• /
• pp.52-59
• /
• 2013

In this study, tests were conducted to establish a fire engine of relay waterproof and utilization in order to maintain the pressure in a situation that require high-pressure water-resistant such as a high-rise building fire, etc. As a result of test on the change of a relay waterproof pressure, the measurement result with the hydrant intake of a fire engine opened has reduced approximately 20 % compared to the measurement result with the hydrant intake closed. Similar efficiency showed in the test result that change the pressure of 2 fire engines respectively to use them more efficiently at a fire fighting activity site. A fire engine operation and utilization is proposed based on this study result in order to cope effectively with a fire site requiring high-pressure stream in a high-rise building fire, etc. by using a fire engine held at present because there is no fire pump with high-pressure stream ability arranged at the fire station and there is no regulation on high-pressure fire-fighting pumps in a type approval and verification technology criterion for a fire engine.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.267-272
• /
• 2010

High pressure x-ray diffraction patterns of ${\alpha}$-cristobalite gallium phosphate ($GaPO_4$) were acquired up to 8.9 GPa at room temperature using Mao-Bell type diamond anvil cell with high flux synchrotron radiation. Starting orthorhombic phase (phase-I) shows the splitting of peak which is possibly resulted from the pressure induced orientation disorder of the framework structure of tetrahedra. This is designated as phase-I'. This phase transforms to the orthorhombic high pressure phase-III between 2 and 3 GPa. Present phase transition sequence is not in accord with the recent high pressure X-ray diffraction results performed on the same starting sample (Ming et al., 2007). X-ray pattern of the unloaded sample to ambient pressure shows that the structure retains that of the high pressure phase prior to decompression.