• 한국전기전자재료학회논문지
• /
• 제29권1호
• /
• pp.40-43
• /
• 2016

Transparent color coating films were fabricated on a glass substrate by using sol-gel hybrid binder and organic dye. Sol-gel hybrid binder coating film fabricated with PTMS of 0.03 mole showed a very high pencil hardness of 9 H. As the withdrawal speed increased from 1.0 mm/s to 5.0 mm/sec, The yellowness ($b^*$) of coating glass also gradually increased. The transmittance of yellow color coating glass was 82.6% and the haze of coating glass was 0.35%. Red and blue color coating glasses also showed the high transmittance of 62.4% and 80.6% respectively. The surface hardness of color coating films was 6 H.

• Journal of Ceramic Processing Research
• /
• 제20권1호
• /
• pp.59-62
• /
• 2019

Y2O3-MgO nanocomposites are promising materials for hypersonic infrared windows and domes due to their excellent midIR transmittance and mechanical properties. In this work, influence of SPS heating rate on the microstructure, IR transmittance, and mechanical properties of Y2O3-MgO nanocomposites was investigated. It was found that the average grain size decreases with a decreasing heating rate, which can be attributed to high defect concentration by rapid heating and deformation during densification. Also, the residual porosity decreases with a decreasing heating rate, which is ascribed to the enhancement of grain boundary diffusion by a large grain-boundary area (a small grain size). Consequently, high transmittance and hardness were attained by the low heating rate. On the other hand, the mechanical strength showed little difference with the heating rate change, which is somewhat different from the general knowledge on ceramics and will be discussed in this letter.

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.65-69
• /
• 2004

We synthesized photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the photopolymer surface can be obtained. However, the low pretilt angles were obtained below 1$^{\circ}$. The Voltage-transmittance (V-T) curve without backflow bounce in the photoaligned TN cell with UV exposure was observed. The response time of photoaligned TN cell was measured about 24 ms. Finally, The photoaligned TN cell has few hysteresis, and shows the residual DC voltage that is less.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 디스플레이 광소자분야
• /
• pp.210-213
• /
• 2004

We synthesized photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the photopolymer surface can be obtained. However, the low pretilt angles were obtained below $1^{\circ}$. The Voltage-transmittance (V-T) curve without backflow bounce in the photoaligned TN cell with UV exposure was observed. The response time of photoaligned TN cell was measured about 24 ms. Finally, The photoaligned TN cell has few hysteresis, and shows the residual DC voltage that is less.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.244.1-244.1
• /
• 2015

The Ag Nanowire is one of the materials that are widely studied as alternatives to ITO and is available for large area, low cost process and the flexible transparent electrode. However, Ag nanowire can have the problem of a lack of stability at high temperatures, making this impossible to form a film. Using a structure of ITO/AgNW/ITO in photodetector device, we improved the properties of the ITO in the IR region and improved the thermal stability of the AgNW. The structure of ITO/AgNW/ITO has a high transmittance value of 89% at a wavelength of 900 nm and provide a good electrical property. The AgNWs embedded ITO film has a high transmittance, this is because of the light scattering from the AgNW. The thermal stability of the developed ITO/AgNWs/ITO films were investigated and found AgNWs embedded ITO films posses considerable high stability compared to the solo AgNWs on the Si surface. The ITO/AgNWs/ITO device showed a improved photo-response ratio compared to those of the conventional TC device in IR region. This is attributed to the high transmittance and low sheet resistance. We suggest an effective design scheme for IR-sensitive photodetection by using an AgNW embedded ITO.

• 한국진공학회지
• /
• 제17권2호
• /
• pp.138-147
• /
• 2008

RF 스퍼터링 시스템을 이용하여 $SiO_2/TiO_2/ZrO_2$ 광대역 반사방지막을 단계별로 제작하였고, 분광타원계와 $UV-V_{is}$ 분광광도계를 이용하여 박막의 두께, 굴절률 및 투과율 스펙트럼을 300$\sim$900nm의 파장 영역에 걸쳐 측정 및 분석하였다. 측정 및 분석된 박막의 두께, 굴절률 및 투과율 스펙트럼을 설계값과 비교 평가한 결과 각층의 두께, 굴절률의 차이에 따른 투과율의 변화를 분석할 수 있었고, 박막의 두께보다는 굴절률과 굴절률의 분산형태가 투과율의 변화에 더 크게 기여함을 알 수 있었다.

• KIEAE Journal
• /
• 제10권3호
• /
• pp.43-50
• /
• 2010

Natural lighting is directly connected with our mental and physical health. For working or learning effect, the proper natural lighting is required for improving our living conditions. School facilities, especially, are the place where includes students' ordinary activities with learning behaviors during the school years from elementary to high school. This study was carried out for the purpose introducing a basic database in that planning a school by researching on the actual in the natural lighting system of some schools' classroom, estimating, and analyzing through a simulation, which resulted in a method of improving the natural lighting system. As a result of measuring and analyzing Daylight Factor(DF) during the time from 9 am to 3 pm when students are activating in their classroom, generally DF range of the sides near to window and aisle seats zone are not distributed well. Besides, two out of four school which are researched would not reach the standards of the law for school sanitary while rest of the schools meet the standards; Average DF 5% and Minimum DF 2%. And the result of a simulation by RADIANCE program shows the most appropriate DF range when it is applied in variable numbers about an oriehows the- South-east 15, south-east 30, south-east 45, south-west 15, south-west 30, and south-west 45 degrees. When it is applied in the variable numbers about glass transmittance - 60%, 70%, and 80% in condition facing south of a classroom, the result shows that the DF range of 80% transmittance is relatively higher than other glasses in the classroom. Thus, when a school is built, plans for an orientation is necessary for improve of elementary schools' environment with the glass installation which is made for high transmittance and is regarded with the students' activities time.

• 센서학회지
• /
• 제24권4호
• /
• pp.264-269
• /
• 2015

An infrared (IR) bolometer measures the change of resistance by absorbing incident IR radiation and generates a signal as a function of the radiation intensity. Since a bolometer requires temperature stabilization and light filtering except for the infrared rays, it is essential for the device to be packaged meeting conditions that above mentioned. Minimization of heat loss is needed in order to stabilize temperature of bolometer. Heat loss by conduction or convection requires a medium, so the heat loss will be minimized if the medium is a vacuum. Therefore, vacuum packaging for bolometer is necessary. Another important element in bolometer packaging is germanium (Ge) window, which transmits IR radiation to heat the bolometer. To ensure a complete transmittance of IR light, anti-reflection (AR) coatings are deposited on both sides of the window. Although the transmittance of Ge window is high for IR rays, it is difficult to use frequently in low-price IR bolometer because of its high price. In this paper, we fabricated IR window by utilizing silicon (Si) substrate instead of Ge in order to reduce the cost of bolometer packaging. To enhance the IR transmittance through Si substrate, it is textured using Reactive Ion Etching (RIE). The texturing process of Si substrate is performed along with the change of experimental conditions such as gas ratio, pressure, etching time and RF power.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.433.1-433.1
• /
• 2014

The research of graphene, a monolayer of carbon atoms with honeycomb lattice structure, has explosively increased after appeared in 2004. As a result, its high transmittance, mobility, thermal conductivity, and outstanding mechanical and chemical stability have been proved. Especially, many researches were executed about the field of transparent electrode highlighting material of substituting the indium tin oxide (ITO). In addition, qualitative and quantitative improvements have been achieved due to many synthesis methods were discovered. Among them, mostly used method is chemical vapour deposition of graphene grown on copper or nickel. The transmittance, mobility, sheet resistance, and other many properties are completely changed according to these two types of synthesis method of graphene. In this research, considering the difference of characteristics as the synthesis method of graphene, what types of graphene should be used and how to use it were studied. The stacked graphene harvested on copper and multi-layer graphene harvested on nickel were compared and analyzed, as a result, the transmittance of 90% and the sheet resistance of $70{\Omega}{\square}$ was showed even though stacked graphene layers were 4 layers. The reason that could bring these results is lowered sheet resistance due to stacked monolayer graphenes. Moreover, light output power of the three stacked graphene spreading layer shows the highest value, but light-emitting diode with multi-layer graphene died out from 12mA due to also its high sheet resistance. Therefore, we need to clarify about what types of graphene and how to use the graphene in use.

• 한국정보통신학회논문지
• /
• 제14권4호
• /
• pp.935-938
• /
• 2010

현재까지 개발된 투명전극재료 중에는 ITO가 가장 투명하면서 전기도 잘 통하고 생산성도 좋다. 투명전극은 비저항이 $1{\times}10^{-3}{\Omega}/cm$이하, 면저항이 $10^3{\Omega}/sq$이하로 전기전도성이 우수하고 380에서 780nm의 가시광선 영역에서의 투과율이 80%이상이라는 두 가지 성질을 만족시키는 박막이다. 본 연구에서는 스퍼터링 진공 증착 장치를 이용하여 투명 도전막(ITO: Indium Tin Oxide)을 제작하고 제작된 ITO 박막의 광 및 전기 그리고 물성적 특성을 조사하여 최상의 공정 조건을 확립하였다. 본 실험에서는 $In_2O_3:SnO_2$ 의 조성비는 90:10 wt% 인 타겟의 특성이 우수하였고, Ar:$O_2$의 분압비는 100:1 및 42:8의 조건이 적당하였으며, 온도는 $200^{\circ}C$ 가장 우수한 특성을 얻을 수 있었다. 본 연구에서 제작한 박막은 광 투과도가 90% 이상, 비저항이 $300\;{\mu}{\Omega}cm$ 이하의 특성을 갖게되어 이미지센서, 태양전지, 액정 텔레비젼등 빛의 통과와 전도성등 두가지 특성에 동시에 만족 될만한 성능을 가질 수 있음을 확인하였다.