• KIEAE Journal
• /
• v.16 no.1
• /
• pp.5-10
• /
• 2016

Purpose: The energy consumption in buildings has continuously increased in some countries and it reaches almost 25% of the total energy use in korea. Therefore there are various efforts to minimize energy consumption in buildings, and the regulations on building envelope insulation have been tightened up gradually. To satisfy the building regulation, the use of vacuum insulation panels(VIPs) is increasing. VIP is a high performance insulation materials, so that it can be thinner than conventional insulation material. When VIP is applied in a building, it may cause thermal bridge, which occurs due to very low thermal conductivity compared to other building materials and the envelope of VIPs. Method: This study designed the capsulized VIPs using conventional insulation for reduction of the thermal bridge. Then designed VIPs were applied to a wall. The linear thermal transmittance and the effective thermal conductivity were analyzed by HEAT2 simulation program for two dimensional steady-state heat transfer. The result compared with a wall with non-capsulized VIPs. Result: It analyzed that the wall with capsulized VIPs had lower linear thermal transmittance and reduced the difference of the effective thermal transmittance with one dimensional thermal transmittance compared to that of the wall with non-capsulized VIPs.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.256-263
• /
• 2011

Recently, curtain wall structure is constructed according to increasing high rise building. Glass is usually used in opening of curtain wall structure and window area ratio is finally increased. Excessive Daylighting and solar radiation by large window area ratio cause discomfort glare and add to cooling load in the case of office that is heavy on lighting and cooling. Therefore, this study suggests to use low transmittance window for solve those problems. Indoor lighting environment and building energy performance were analyzed by increasing transmittance from 10% to 90% and comparing fixed venetian blind. Consequently, the range of transmittance that is possible to daylighting and prevent discomfort glare. Secondary energy consumption is efficient in the case that transmittance is the range of from 20% to 50%, primary energy consumption is nice on from 20% to 40%. If those result put together, the range of window transmittance from 30% to 50% is proper in the office in lighting environment and energy consumption aspects.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.232-237
• /
• 2009

This study was performed to investigate the effect of high performance greenhouse films on growth and fruit quality of tomato. For this purpose, polyolefin (PO), fluoric, antidrop, antifog and thermal films were compared to normal film, ethylene vinyl acetate (EVA). In spectral irradiance of the films, UV ($300{\sim}400nm$) transmittance was highest in fluoric film and lowest in PO film. PAR (photosynthetically active radiation, $400{\sim}700nm$) transmittance was higher in fluoric, thermal and PO film, and near infrared ray (NIR, $700{\sim}1,100nm$) transmittance was higher in high performance films, compared to the EVA film. Total light transmittance was higher in order of fluoric, antifog, anti drop, PO, thermal, and EVA film. Day air temperature in greenhouse was highest under fluoric film and lowest under EVA film due to the light transmittance, while night air temperature was highest under PO and anti drop film due to the thickness of film. Tomato fruits grown under the high performance films had 0.2 to $0.5^{\circ}Bx$ higher soluble solids and 15 to 30% higher lycopene content, compared to those grown under the EVA film. The results showed that tomato fruit quality such as soluble solids and lycopene content can be heightened in terms of much irradiation and better light quality of high performance films, compared to the nomal film, EVA film.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.1
• /
• pp.45-49
• /
• 1999

To prepare high-transmittance films, thin films were fabricated on the microscope slide glasses with silicon alkoxides and boric acids as starting materials by using a dip-coating technique. Thicknesses of the thin films were controled as viscosity of the sol used and composition of the $B_2O_3$ was changed at 5, 10, 15 and 20 mol%. Transmittance at visible range and IR transmittance of the films according to the composition were measured, and refractive index of the films were analyzed also. Maximum transmittance at visible range and minimum refractive index were obtained at 15 mol% $B_2O_3$. We will discuss a decrease of the transmittance at 20 mol% on the basis of the refractive index.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.592-598
• /
• 2017

A method for estimating the optical characteristics of ceramic materials under high temperature conditions has been applied and evaluated. For that purpose, an interface system combined with a photo-spectrometer was made to keep the samples at the required high temperature. The transmittance of the samples was measured at various temperatures. The measured transmittance data was used to estimate the refractive index using an optical simulation model in conjunction with the Sellmeier equation. The Sellmeier equation parameters were selected by trial-and-error when the transmittance recalculated using the estimated refractive index was compared with the measured transmittance. Furthermore, the estimated refractive indices were checked by a comparison with the reference data at some typical wavelengths at room temperature.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.57-63
• /
• 1999

The optical absorption and transmittance of cow' crystalline were measured by spectrophotometer in the 200~800nm wavelength regions. The optical absorptions of crystalline composed of a high absorption band in the UV-A, UV-B, and appeared the light transmittance edge in the 400nm wavelength region, and completely transmitted without the absorption in the high wavelength regions than 400nm. Also, the optical absorption and transmittance had no temperature dependence. The optical transmittance spectrum of crystalline concord with the thin film structure of $n_0/(0.5H)L(LH)^6(0.5H)/n_s$ and $n_0{\mid}(0.5LH0.5L)^kL/1.25{\mid}4.0$ of long-pass edge filter form. In the artificial crystalline and inter lens layout, long-pass edge filter layout can UV cut off.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.914-922
• /
• 2003

The FFS (fringe-field switching) mode was known to exhibit both a wide viewing angle and high transmittance, especially when using a liquid crystal with negative dielectric anisotropy. We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}$m, the transmittance at the center of pixel and common electrodes is relatively low because effect of surface anchoring that holds the LC to the initial state is larger than that in a large cell gap of 4 .urn such that the LCs in those regions cannot rotate enough. However, in case of a large cell gap of 4 .urn, the effect of surface anchoring becomes relatively small so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we can conclude that the light efficiency is dependent on the cell gap.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.78-83
• /
• 2009

In general, Light-hardening polymer was used UV nanoimprint technology. A light-hardening polymer was had the problem of poor hardness, durability. In order to overcome the problem of polymer, inter change optical glass. However glass is very manufacture and a lowering of standars transmittance. In order to glass recover was necessary polishing process. The process is magnetorheological fluids polishing. MR polishing has been developed as a new precision finishing technique to obtain a fine surface. Hence, Magnetorheological fluids has been used for micro polishing to get micro parts. This polishing process guarantees high polishing quality by controlling the fluid density electrically. The applied material in experiments is fused silica glass. Fused silica glass is widely used in the optical field because of high degree of purity. For MR polishing experiments, MR fluid was composed with DI-water, carbonyl iron and nano slurry ceria. The wheel speed and electric current were chosen as the variables for analyzing the characteristics of MR polishing process. Outstanding surface roughness of Ra=1.58nm was obtained on the fused silica glass specimen. And originally glass transmittance was recover on the fused silica glass.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.49-55
• /
• 2023

The deposition of indium zinc oxide (IZO) thin films was carried out on substrate at room temperature by RF magnetron sputtering. The effects of substrate temperature, RF power and deposition pressure were investigated with respect to physical and optical properties of films such as deposition rate, electrical properties, structure, and transmittance. As the RF power increases, the resistivity gradually decreases, and the transmittance slightly decreases. For the variation of deposition pressure, the resistivity greatly increases, and the transmittance is decreased with increasing deposition pressure. As a result, it was demonstrated that an IZO film with the resistivity of 3.89 × 10^-4 Ω∙cm, the hole mobility of 51.28 cm²/Vs, and the light transmittance of 86.89% in the visible spectrum at room temperature can be prepared without post-deposition annealing.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.168-171
• /
• 2016

There has been growing interest and rapid development in transparent electrode films, which are flexible and light and used in mobile, simple information, and electronic devices, and based on recent advancements in nano technology, information technology, and display technology. In particular, studies on developing such films with both high conductivity and high transmittance of visible rays are highly in demand for commercialization. In this study, transparent electrode films were developed for IT using micro patterns that show sheet resistance less than 10 Ω/□, adhesive strength more than 98%, and light transmittance more than 90%. The results of applying a surface emission gradient minimization (Honey Comb) technology to the films was the verification of the sheet resistance, adhesive strength, and light transmittance satisfying the target level of this study through Imprinting and Remolding processes.