• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.57-64
• /
• 1996

To use effectively the solar energy in greenhouse heating, a high performance solar collector should be developed. And then the size of the solar collector and thermal storage tank should be determined through the calculation of heating load. The solar collector must be set in the optimum tilt angle and direction to take daily solar radiation maximally, and the flow rate of heat transfer fluid through the solar collector should be kept in the optimum range. In this research, the performance tests of a capillary tube solar collector were performed to determine the optimum water flow rate and the results summarized as follows. 1. The regressive equations for efficiency estimations of the capillary tube solar collector in the open loop were modeled in the water flow rate of 700-l,000 $\ell$/hr. 2. The optimum water flow rate of the solar collector was estimated by the second order polynomial regression and the maximum efficiency was 80% at the water flow rate of 850 $\ell$/hr. 3. The solar thermal storage system consisted of a capillary tube solar collector and a water storage tank was tested at the water flow rate of 850 $\ell$/hr in the closed loop, and obtained the solar thermal storage efficiency of 55.2%. 4. As the capillary tube solar collector engaged in this experiment was made of non-corrosive polyolefin tubes, its weight was as light as 1/30 of the flat plate solar collector made of copper tubes. Therefore it was considered to be suitable for the greenhouse heating system.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.3
• /
• pp.120-128
• /
• 2018

OLED Display fabrication system is one of the most complicated discrete processing systems in the world. As the glass size grows from $550{\times}650mm$ to $1,500{\times}1,850mm$ in recent years, the efficiency of Automated Material Handling System (AMHS) has become very important and OLED glass manufacturers are trying to improve the overall efficiency of AMHS. Aiming to meet the demand for high efficiency of transportation, various kind of approaches have been applied for improving dispatching rules and facility layout, while simultaneously considering the system parameters such as glass cassettes due date, waiting time, and stocker buffer status. However, these works did not suggest the operational policy and conditions of distribution systems, especially for handling unnecessary material flows such as detour. Based on this motivation, in this paper, we proposed an efficient algorithm for improving detour transportation in OLED FAB. Specifically, we considered an OLED FAB simplifying OLED production environment in a Korean company, where four stockers are constructed for the delivery of Lot in a bay and linked to processing equipments. We developed a simulation model using Automod and performed a numerical experiment using real operational data to test the performance of three operation policies under considerations. We showed that a competitive policy for assigning alternative stocker in case of detour was superior to the current dedicated policy using a specified stocker and other considered policies.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3629-3633
• /
• 2011

The effect of a dense $TiO_2$ blocking layer prepared using the sol-gel method on the performance of dye-sensitized solar cells was studied. The blocking layer formed directly on the working electrode, separated it from the electrolyte, and prevented the back transfer of electrons from the electrode to the electrolyte. The dyesensitized solar cells were prepared with a working electrode of fluorine-doped tin oxide glass coated with a blocking layer of dense $TiO_2$, a dye-attached mesoporous $TiO_2$ film, and a nano-gel electrolyte, and a counter electrode of Pt-deposited FTO glass. The gel processing conditions and heat treatment temperature for blocking layer formation affected the morphology and performance of the cells, and their optimal values were determined. The introduction of the blocking layer increased the conversion efficiency of the cell by 7.37% for the cell without a blocking layer to 8.55% for the cell with a dense $TiO_2$ blocking layer, under standard illumination conditions. The short-circuit current density ($J_{sc}$) and open-circuit voltage ($V_{oc}$) also were increased by the addition of a dense $TiO_2$ blocking layer.

• Journal of Information Display
• /
• v.4 no.2
• /
• pp.13-18
• /
• 2003

We synthesized bis (2-methyl-8-quinolinolato)(triphenylsiloxy) aluminum (III) (SAlq), a blue-emitting material having a high luminous efficiency, through a homogeneous-phase reaction. The photoluminescence (PL) and electroluminescence (EL) spectra of SAlq show two peaks at 454 nm and 477 nm. Efficient white light-emitting devices are fabricated by doping SAlq with a red fluorescent dye of 4-dicyanomethylene-2-methyl-6-{2-(2,3,6,7-tetrahydro-1H,5H-benzo[i,j]quinolizin-8yl) vinyl}-4H-pyran (DCM2). The incomplete energy transfer from blue-emitting SAlq to red-emitting DCM2 results in light-emission of both blue and orange colors. Devices with the structure of ITO/TPD (50 nm)/SAlq:DCM2 (30 nm, 0.5 %)/$Alq_3$ (20 nm)/LiF (0.5 nmj/Al show EL peaks at 456 nm and 482 nm originating from SAlq and at 570 nm from DCM2, resulting in the Commission Internationale d'Eclairage (CIE) chromaticity coordinates of (0.32, 0.37). The device exhibits an external quantum efficiency of about 2.3 % and a luminous efficiency of about 2.41m/W at 100 $cd/m^2$. A maximum luminance of about 23,800 $cd/m^2$ is obtained at the bias voltage of 15 V.

• International Journal of Computer Science & Network Security
• /
• v.21 no.9
• /
• pp.267-274
• /
• 2021

The article deals with problems of innovation development on a network basis, which require effective mechanisms of innovation communications. In research the organizational aspects of ICT infrastructure development for innovation networks sustainable development based on cooperative marketing principles is considered. The proposed research idea is based on the idea that ICT implementation is based not only on the operational approach for innovation management as a factor of efficiency of internal communications, but also on knowledge economy and post-industrial economy trends. Therefore, the purpose of study is to develop an ICT model of innovation infrastructure to improve its effectiveness (strategic character) and efficiency (operative character) through increasing the efficiency of network communication interactions. Creation of information space and communication tools to support innovation network sustainable development and cooperation activities in research is proposed to be solved with the help of specialized ICT platform. It is shown, that ICT platform of innovation cooperation innovation network is important tool for common work of participants. ICT platform is considered as an integrated information system designed to automate business processes related to the sustainable development of innovation network, segment management and integration with HEI information systems and industrial cooperation. The main factors that determine the need to use a special ICT platform for innovation network cooperation were considered. The main issues of concurrent engineering (C-technology) application in high-technology industries and innovation cooperation for integrated product development were studied.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.1
• /
• pp.62-67
• /
• 2007

It was investigated to develop the technology for simultaneous removal of $SO_2/NO$ in flue gas using liquid homogeneous catalyst. Test was carried out using a bench scale and a pilot scale experiment. The investigation led to the following results: 1) Removal efficiency of $SO_2$ gas showed good results regardless of operating condition. Removal efficiency of NO gas, however, proportionally increased with higher packing height, lower concentration and larger injection rate of catalyst 2) The optimum design parameters for simultaneous removal of $SO_2/NO$ gas using Fe(II)-EDTA catalyst were as follow: HTU(height of transfer unit) = 0.5 m, liquid gas ratio = 20 $L/m^3$, NTU (number of transfer unit) = 3 stages, cross dimension of scrubber=0.025 $m^2$ 3) The removal efficiencies of $SO_2$ and NO were 95% and 81%, repletely. 4) The high HTU is advantageous on removal of the NO, but the excessive HTU diminishes operating efficiency. Consequently, it is important to decide the HTU of optimum.

• Journal of Embryo Transfer
• /
• v.10 no.2
• /
• pp.105-113
• /
• 1995

This study was conducted to examine the efficiency of enucleation and blastomere isolation from recipient oocytes and donor embryos, respectively and to determine the effect of oocyte age and electric voltage on the fusion rate and in vitro development of the fused oocytes in rabbit nuclear transplantation. Immature oocytes collected from ovarian follicles were matured in vivo for 12 h in TCM-199 containing FCS and hormones and in vivo matured oocytes were collected 17 to 18 h post-HCG. The fresh and frozen donor embryos of 8- to 16-cell stage were collected from the oviduct of superovulated does. The proportion of successfully enucleated oocytes was greatly lower in in vitro matured oocytes (42.3%) than that (62.7%) in in vivo matured oocytes The level of cytochalasin B for in vivo matured oocytes did not affect the efficiency of enuleation, but 7.5 $\mu$g /mL cytochalasin B for in vitro matured oocytes showed a high enucleation rate significantly. The isolation efficiency of a single blastomere nucleus did not differ between 8- and 16-cell stage embryos. The percentage of single blastomeres isolated from 16-cell stage fresh embryos after 0.5% pronase treatment was greatly higher at 16-min treatment (94.4%) than at 8-min(78. 1%) and the blastomeres(61.5%) isolated from frozen-thawed embryos after 16-min pronase were significantly fewer than those of fresh embryos. The age of recipient oocytes affected nuclear fusion rate. The reconstituted oocytes fused at 24-h age showed slightly higher fusion rate (77.8%) than those (65.0%)fused at 18-h age. The fusion rate of in vitro and in vivo matured oocytes inserted with fresh blastomere did not differ among electric voltages, but the cleavage rate and development to morula-blastocysts of in vitro matured oocytes was more higher under 0.6 kV/cm than under 0.8 to 1.2 kV/cm, while the cleavage rate and development of in vivo matured oocytes was higher under 0.8 to 1.0 kV/cm than under 1.2 kV/cm. The fusion and cleavage rate fol1owing insertion with frozen-thawed blastomere was not different between the in vitro and in vivo matured oocytes and was similar to those from fresh blastomere insertion.

• Progress in Medical Physics
• /
• v.18 no.3
• /
• pp.144-148
• /
• 2007

Current digital radiography systems are rapidly glowing in clinical applications. The purpose of this study was to evaluate the characteristics of a mobile digital radiographic system. The performance of the mobile DR system was evaluated by measuring the modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE). Measurements were made on a LISTEM Mobix-1000 generator and a Teleoptic PRA Alpha-R4000 detector. Imaging characteristics were measured for these two systems using the IEC-61267 defined RQA5 (kVp: 74, additional filtration: 21 mmAl) radiographic condition. The MTF at 10% was measured as 2.4 cycles/mm and the DQE(0) values for radiation exposure 0.19, 0.5, and 1.3 mR were measured as 54%, 55%, and 76%, respectively. The NPS curves gradually decreased at high spatial frequencies. This high DQE at low frequencies, may be useful for low frequency information. The results suggested that mobile DR system could be integrated with emergency ambulance system in teleradiologic imaging applications.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.1
• /
• pp.6-12
• /
• 2005

Contamination of soils and groundwater by leakage of petroleum compounds from underground storage tanks (USTs) has become great environmental issues. Conventional methods such as soil vapor extraction (SVE) used for the remediation of unsaturated soils contaminated with volatile organic compounds might not be applied for the removal of semi-volatile organic compounds such as diesel fuels and PCBs, which have low volatility and high hydrophobicity. The objective of this study is to develop a hot air injection method to remove semi-volatile compounds. Additionally, operation parameters such as temperature, air flow rate, and water content are evaluated. Experimental results show that diesel ranged organics (DROs) are removed in the order of volatility of organic compounds. As expected, removal efficiency of organics is highly dependent on the temperature. It is considered that more than $90\%$ of organic contaminants whose carbon numbers range between 17 and 22 can be removed efficiently by the hot air injection-extraction method (modified SVE) over the $100^{\circ}C$. It is also found that increased air flow rate resulted in high removal rate of contaminants. However, air flow rate over 40 cc/min is not effective for the operation aspects, due to mass transfer limitation on the volatilization rate of the contaminants. The effect of the water content on the decane removal is minimal, but some components show large dependence on the removal efficiency with increasing water content.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.3
• /
• pp.19-24
• /
• 2014

Development of long-term mobile energy sources for mobile robots or small-sized unmanned vehicles are actively increasing. The micro gas turbine generator (MTG) is a good candidate for this purpose because it has both of high energy density and high power density, and 500W class MTG is under development. The designed MTG can be divided into 2 main parts. One part consists of motor/ generator and compressor, and the other one consists of combustor, recuperator and turbine. 500W class MTG is designed to operate at ultra-high speed of 400,000 rpm in high turbine temperature over $700^{\circ}C$ to improve the efficiency. Because the magnetism of NdFeB permanent magnet for the motor/generator could be degraded if the temperature is over $150-200^{\circ}C$, MTG needs the thermal insulation to block the heat transfer from combustor/turbine side to motor/generator side. Moreover, the motor/generator is allocated to get the cooling effect from the rapid air flow by the compressor. This study presents the experimental results to verify whether the thermal insulator and air flow are effective enough to keep the motor/generator part in the low temperature less than $100^{\circ}C$. From the motoring test by using the high temperature test rig, it was confirmed that the motor/generator part could maintain the temperature less than $50^{\circ}C$ under the condition of 1.0 bar compressed air.