• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.330-333
• /
• 2005

The paper presents a numerical solution to the problem of a hot rigid indenter siding over a thermoelastic Winkler foundation with a thermal contact resistance at constant speed. It is shown analytically that no steady-state solution can exist for sufficiently high temperature or sufficiently small normal load or speed regardless of the thermal contact resistance. However, the steady state solution may exist in the same situation if the thermal contact resistance is considered. This means that the effect of the large values of temperature difference and small value of force or velocity which occur at no steady state can be lessened due to the thermal contact resistance. When there is no steady-state the predicted transient behavior involves regions of transient stationary contact interspersed with regions of separation regardless of the thermal contact resistance. Initially, the system typically exhibits a small number of relatively large contact and separation regions, but after the initial transient the trailing edge of the contact area is only established and the leading edge loses contact, reducing the total extent of contact considerably. As time progresses, larger and larger number of small contact areas are established, until eventually the accuracy of the algorithm is limited by the discretization used.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1467-1471
• /
• 2007

The green-emitting CeMgAl11O19:Tb (CMAT) phosphor has been prepared at 1200 °C by the simple solid-state reaction using AlF3 as a self-flux. This preparation temperature is much lower than those (1500-1700 °C) for conventional solid-state reaction and spray pyrolysis method. In particular, the complete process to produce high-quality phosphor particles was carried out through the single-step heat treatment of the mixture of corresponding oxide-type metal sources. An addition of AlF3 as a self-flux significantly decreased the crystallization temperature of CMAT with plate-like shape. The particle morphology could be controlled from plate-like to spherical by using H3BO3 as an additional flux. Thus, an optimal morphology and luminescence characteristics of CMAT were achieved when both AlF3 and H3BO3 fluxes were simultaneously used. Compared with conventional solid-state process, which is accompanied by the calcination step(s), and other alternative liquid solution techniques such as sol-gel method and spray pyrolysis, no use of active precursors and liquid media that are harmful to the environment is a distinctive advantage for the industrial purpose.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.170.2-170.2
• /
• 2007

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.2
• /
• pp.16-19
• /
• 2003

Quench and recovery process of high-temperature-superconductor (HTS) film deposited on the sapphire substrate is studied numerically. The quench is developed by fault current and the superconductivity is recovered by convection of heat into coolant. After the fault current. the HTS film experiences the quench state. current sharing state. and finally recovers the superconductivity. Numerical results of this study are compared to the previous experimental results. and shows that this numerical work can explain the mechanism of quench/recovery characteristics of HTS film.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.272-275
• /
• 2003

Quench and recovery process of high-temperature-superconductor(HTS) film deposited on the sapphire substrate is studied numerically. The quench is developed by fault current and the superconductivity is recovered by convection of heat into coolant. After the fault current, the HTS film experiences the quench state, current sharing state, and finally recovers the superconductivity. Numerical results of this study are compared to the previous experimental results, and shows that this numerical work can explain the mechanism of quench/recovery characteristics of HTS film.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.181-184
• /
• 2003

Quench and recovery process of high-temperature -superconductor (HTS) film deposited on the sapphire substrate is studied numerically. The quench is developed by fault current and the superconductivity is recovered by convection of heat into coolant. After the fault current, the HTS film experiences the quench state, current sharing state, and finally recovers the superconductivity. Numerical results of this study are compared to the previous experimental results, and shows that this numerical work can explain the mechanism of quench/recovery characteristics of HTS film.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.6-7
• /
• 2003

The inertial fusion research at ILE, Osaka moves to the fast ignition scheme with using PW laser system to achieve hot core plasma of keV-temperature by heating additionally the dense plasma imploded by the multi-beam Gekko laser system. The solid-state lasers have been developed of the peak-power from TW to PW region with the chirped pulse amplification (CPA) and optical parametric amplification (OPA) technology. (omitted)

• Journal of Astronomy and Space Sciences
• /
• v.2 no.2
• /
• pp.153-174
• /
• 1985

The one of critical factor in gas turbine engine performance is high turbine inlet gas temperature. Therefore, the turbine rotor has so many problems which must be considered such as the turbine blade cooling, thermal stress of turbine disk due to severe temperature gradient, turbine rotor tip clearance, under the high operating temperature. The purpose of this study is to provider the temperature distribution and heat flux in turbine disk which is required to considered premensioned problem by the Finite Difference Method and the Finite Element Methods on the steady state condition. In this study, the optimum aspect ratio of turbine disk was analysed for various heat conductivity of turbine disk material by Finite Difference Method, and the effect of laminating method with high conductivity materials to disk thickness direction by Finite Element Methods in order to cool the disk. The laminating method with high conductivity material on the side of the disk is effective.

• Journal of Biosystems Engineering
• /
• v.28 no.3
• /
• pp.225-230
• /
• 2003

This study was carried out to analyze the environmental variation of layer house at Iowa State in the USA. The analyzed seasons for this study were summer and winter. Analyzing factors are inside temperature and relative humidity, carbon dioxide concentration, ammonia concentration and emission. All factors were collected every 30 second from each house with portable monitoring units. In this study, two types of laying hen houses were monitored at the same season. One was a manure belt house, the other was a high-rise house. In order to estimate the ventilation rates of the laying hen houses, carbon dioxide concentration balance was used in this study. Ammonia concentrations and emission rates of the manure belt house are much lower than those of the high rise house. Daily mean ammonia concentrations in the manure belt house and high-rise house ranged from 3 to 7 ppm and 5 to 34 ppm, respectively. The daily ammonia emission rates averaged 0.68g/h$\cdot$500kg and 0.73g/h$\cdot$500kg for the manure belt house and 0.93g/h$\cdot$500kg and 2.89g/h$\cdot$500kg for the high-rise house in summertime and wintertime, respectively. Summertime is associated with much higher ammonia emission rates than wintertime because of much higher ventilation rates and ambient air temperature, even though the concentrations may be lower.

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.6
• /
• pp.908-913
• /
• 1999

This experiment was conducted in three trials to evaluate optimal ambient temperature for a novel milk replacer feeding system designed for early-weaned pigs, compared to commercial dry diets fed within a conventional hot nursery. A total of 165 PIC genotype pigs were weaned at $13.89{\pm}0.7$ days of age and allotted to one of two dietary treatments in three trials based on weight and litter origin. Each trial consisted of pigs fed dry diets (DD) and pigs fed milk replacer (MR) which was offered in one of 3 different ambient temperatures. Pigs fed milk replacer were housed in a specialized nursery building in which one half of each pen contained an enclosed hover that was thermostatically maintained at $32^{\circ}C$ while the exterior ambient temperature (where milk was fed) was set at either 17 (trial 1), 24 (trial 2) or $32^{\circ}C$ (trial 3). Pigs fed dry diets with the conventional nursery were maintained at $30^{\circ}C$ for each trial. From d 21 to d 49, all pigs were fed DD within a standardized hot nursery environment. During the first week (d 14-21), pigs fed MR showed increased ADG from 214% to 228% over control pigs fed DD (p<0.001), regardless of ambient temperature. As ambient temperature was increased from 17 to 24 to $32^{\circ}C$, ADG of MR-fed pigs was increased by 214%, 220% and 228% over those of pigs fed DD, respectively. ADFIs of MR-fed pigs at $17^{\circ}C$, $24^{\circ}C$, and $32^{\circ}C$ compared with pigs fed DD were increased by 108%, 139% and 164% from d 14 to d 21, respectively. Fed efficiency (G/F) of MR-fed pigs at $17^{\circ}C$, $24^{\circ}C$, and $32^{\circ}C$ compared with pigs fed DD were 199%, 162% and 139% of those of pigs fed DD, respectively. As ambient temperature increased, diarrhea scores showed a slight tendency to increase. The advantage of MR feeding was greater when the ambient temperature was higher, but G/F was impaired with increased ambient temperature. We conclude that ambient temperature within the specialized nursery influenced behavior, MR feed intake, and probably piglet energy expenditure. There were no differences between MR-fed and DD-fed pigs for ADG, ADFI and G/F in the subsequent growth period (d 21 to d 49, p>0.05). Maximal advantage of MR feeding was obtained at the intermediate ($24^{\circ}C$) ambient temperature during the overall period (p<0.05). Results from this experiment indicate that a milk replacer feeding system utilized in the early postweaning period can maximize pig growth performance, and that ADG, ADFI and G/F were affected by different ambient temperatures within MR-fed pigs. The high or low temperatures could not support the maximal growth of pigs fed MR.