• 한국건설순환자원학회논문집
• /
• 제8권2호
• /
• pp.204-211
• /
• 2020

PLA(Poly-Lactic Acid)섬유는 친환경소재이며 자연분해가 되므로 건설재료에 사용할 경우 내부 공극연결구조를 가진 다공성 재료의 제조가 가능하다. 본 연구에서는 국내에서 생산된 PLA 섬유(직경 0.5mm, 1.0mm, 길이 10mm)를 대상으로 강알칼리와 고온에서의 용해실험을 수행하였으며, 이를 이용하여 FA기반 지오폴리머에 활용하였다. 고온양생과 강알칼리 용액을 통하여 강도는 확보하였으나, 완전한 PLA 섬유의 용해을 확보하지 못하였다. 기존의 연구인 0.003mm의 직경에서는 완전히 용해하였으나 0.5mm는 약 42.5%, 1.0mm는 약 33.3%의 용해율을 가지고 있는 것으로 평가되었다. 또한 섬유의 체적이 커짐에 따라 양생시 부유하는 섬유가 발생하여 작업성과 용해에 부정적인 영향을 나타내었다. PLA 특성은 생산하는 원재료와 생산조건에 따라 달라질 수 있으나, 다공성 건설 자재로서 사용하기 위해서는 0.1mm 내외의 PLA 섬유의 사용이 바람직하다고 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1852-1854
• /
• 1999

In order to enhance satellite communication system performance, filters are required with the characteristics of sharp skirt, low insertion loss, and high power handling capability. But the performance of microwave passive filters is significantly declined by the conduction losses, especially in case of planar structures using film conductors. By using high temperature superconducting(HTS) film material as the conductor, higher performance could be expected. We have designed and developed narrow bandpass filters using haripin-type superconducting microstrip line for satellite communication. High quality superconducting YBCO thin films have been grown on MgO substrates by pulsed laser deposition(PLD) The deposited YBCO films were patterned by conventional wet-etching process. The transition temperatures of these films had shown 86 - 89 K. The film thicknesses were about 500 nm. Experimental results are presented for the insertion loss and return loss of the filter at 60 K.

• 한국재료학회지
• /
• 제14권4호
• /
• pp.251-259
• /
• 2004

In the development of the advanced spent fuel management process based on the molten salt technology, it is essential to choose the optimum material for the process equipment handling molten salt. Corrosion behavior of Ni 200 and Ni-base alloys in molten salt of LiCl-$Li_2$O under oxidation atmosphere was investigated in the temperature range of $650～800^{\circ}C$ for 24～312 hrs. The order of corrosion rate was Ni 200 > Inconel 690 > Inconel 601 > Inconel 600. Inconel 600 alloy showed the highest corrosion resistance among the examined alloys, but Ni 200 exhibited the highest corrosion rate. Corrosion products of Inconel 600 and Inconel 601 were $Cr_2$$O_3$ and $NiFe_2$$O_4$. In case of Inconel 690, a single layer of $CrO_2$$O_3$ was formed in the early stage of corrosion and an outer layer of $NiFe_2$O$_4$ and inner layer of $Cr_2$$O_3$ were formed with increase of corrosion time. Inconel 600 showed local corrosion behavior and Inconel 601, 690 showed uniform corrosion behavior.

• 대한안전경영과학회지
• /
• 제16권2호
• /
• pp.81-90
• /
• 2014

Flexible production system has been expanded to all sectors of economy with the change of labor market and diversification of employment. The unstable employment with irregular work has replaced stable employment with regular work. This study has investigate the impact pathway of the type of employment on health status especially ill-health symptoms experiences. Among the first Korean Working Conditions Survey data, the employee's response data was used to analyze the path way with multiple regression analysis. The result has shown the direct effect of the type of employment on ill-health symptoms experience. Indirect effect of the type of employment was found the pathway via the exposure to noise, high temperature, low temperature, dust, skin contact to chemicals, painful posture, heavy material handling, standing position, repetitive movement of hands. However the exposure to the other hazardous factors such as organic solvent, wholebody vibration, radiation, lifting people, infectious materials were not influenced by the type of employment.

• 한국컴퓨터정보학회논문지
• /
• 제28권8호
• /
• pp.165-174
• /
• 2023

본 연구는 국내 근로환경조사 자료를 이용하여 조사 시기에 따른 제조업 종사자의 유해·위험요인 노출과 결근과의 관련성을 확인하였다. 이에 2011년도(3차), 2017년도(5차), 2020년도(6차)의 유해·위험요인 동일문항에 대하여 제조업 종사자 8,318명을 대상으로 분석하였다. 업무 관련 유해·위험인자와 결근과의 관련성을 보면 2011년도에 비하여 2020년도에 진동, 소음, 높은 온도, 먼지 등의 흡입, 증기흡입, 화학물질 취급, 감염물질 취급에서 노출 시간 3/4 이상이 결근에 영향을 미치는 것으로 나타났다. 결론적으로 업무 관련 유해·위험요인에 대해서는 조사시기가 증가함에 따라 비노출이 증가함을 알 수 있었고 업무 관련 유해·위험요인의 노출 시간이 결근에 영향을 미친다는 것을 확인할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.292-295
• /
• 2004

The SIT was introduced by Nishizawa. in 1972. When compared with high-voltage, power bipolar junction transistors, SITs have several advantages as power switching devices. They have a higher input impedance than do bipolar transistors and a negative temperature coefficient for the drain current that prevents thermal runaway, thus allowing the coupling of many devices in parallel to increase the current handling capability. Furthermore, the SIT is majority carrier device with a higher inherent switching speed because of the absence of minority carrier recombination, which limits the speed of bipolar transistors. This also eliminates the stringent lifetime control requirements that are essential during the fabrication of high-speed bipolar transistors. This results in a much larger safe operating area(SOA) in comparison to bipolar transistors. In this paper, vertical SIT structures are proposed to improve their electrical characteristics including the blocking voltage. Besides, the two dimensional numerical simulations were carried out using ISE-TCAD to verify the validity of the device and examine the electrical characteristics. A trench gate region oxide power SIT device is proposed to improve forward blocking characteristics. The proposed devices have superior electrical characteristics when compared to conventional device. Consequently, the fabrication of trench oxide power SIT with superior stability and electrical characteristics is simplified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1108-1109
• /
• 2008

To survive in outdoor environments, photovoltaic modules rely on packaging materials to provide requisite durability. We analyzed the properties of encapsulant materials that are important for photovoltaic module packaging. Recently, the thickness of solar cell gets thinner to reduce the quantity of silicon. And the reduced thickness make it easy to be broken while PV module fabrication process. Solar cell's micro cracks are increasing the breakage risk over the whole value chain from the wafer to the finished module, because the wafer or cell is exposed to tensile stress during handling and processing. This phenomenon might make PV module's maximum power and durability down. So, when using thin solar cell for PV module fabrication, it is needed to optimize the material and fabrication condition which is quite different from normal thick solar cell process. Normally, gel-content of EVA sheet should be higher than 80% so PV module has long term durability. But high gel-content characteristic might cause micro-crack on solar cell. In this experiment, we fabricated several specimen by varying curing temperature and time condition. And from the gel-content measurement, we figure the best fabrication condition. Also we examine the crack generation phenomenon during experiment.

• 한국세라믹학회지
• /
• 제56권5호
• /
• pp.468-473
• /
• 2019

This study focused on manufacturing an inorganic insulation material set with various amounts of calcium-sulfoaluminate (CSA) (hauyne) content for enhancing both workability (demolding, handling) and the high thermal insulating property. To carry out the experiment, the amounts of CSA utilized were 5%, 10%, 15%, and 20%, with anhydrous gypsum added in equal proportion to produce a stable formation. As the content of CSA increased, a sinking phenomenon occurred because of the hydration reaction from the slurry, so it was difficult to utilize a retarder normally used in the cement manufacturing process. However, an RCOOM surfactant was able to solve the local clumping problem from cement and CSA and obtain a rapid retarding effect, so it was included in this process at 0.3%. Furthermore, the cement fineness was not 7000 ㎠/g but rather 3300 ~ 4000 ㎠/g to prevent a rapid temperature increase in the slurry. The specific gravity of the sample manufactured with 20% CSA was approximately 0.11 g/㎤, and its thermal conductivity was 0.041 W/m·K, providing an excellent insulating property.

• 한국포장학회지
• /
• 제28권1호
• /
• pp.67-73
• /
• 2022

The food cold chain refers to a technology and distribution supply chain applied to maintain a constant temperature suitable for the product from production (harvest) to delivery to consumers. In particular, in Korea, the insulation material used in the food cold chain is mostly EPS (Expanded Polystyrene), which is used as a transport container for various food cold chains. However, according to the government's eco-friendly policy, companies charge environmental contributions to the use of EPS, but due to its low price and convenience of handling, it is still used as a container for delivering food. In this study, in order to measure the domestic delivery environment of general refrigerated foods, changes in impact, temperature, and humidity during transport of the EPS packaging system containing foods and ice pack refrigerants were measured. As a result, there were 2?3 sections in which a high impact force of 40 G or more was generated during transport. This can cause damage to the product and EPS container. The difference in temperature and humidity changes by parcel transport routes is more than 30%, so it is necessary to present accurate standards for the domestic cold chain distribution environment. As a result of microbial experiments. the transportation period had a dominant effect on the increase in total viable count and E. coli count.

• 대한금속재료학회지
• /
• 제46권9호
• /
• pp.577-584
• /
• 2008

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Inconel 713LC, Inconel MA 754, Nimonic 80A and Nimonic 90 in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere was investigated at $650^{\circ}C$ for 72~216 hrs. Inconel 713LC alloy showed the highest corrosion resistance among the examined alloys. Corrosion products of Inconel 713LC were $Cr_2O_3$, $NiCr_2O_4$ and NiO, and those of Inconel MA 754 were $Cr_2O_3$ and $Li_2Ni_8O_{10}$ while $Cr_2O_3$, $LiFeO_2$, $(Cr,Ti)_2O_3$ and $Li_2Ni_8O_{10}$ were produced from Nimonic 80A. Also, corrosion products of Nimonic 90 were found to be $Cr_2O_3$, $(Cr,Ti)_2O_3$, $LiAlO_2$ and $CoCr_2O_4$. Inconel 713LC showed local corrosion behavior and Inconel MA 754, Nimonic 80A, Nimonic 90 showed uniform corrosion behavior.