• 한국재료학회지
• /
• 제19권11호
• /
• pp.619-624
• /
• 2009

Titanium alloys have been attractive due to a high ratio of strength to weight as well as good corrosion resistance. However, strengthening causes a decrease in ductility in Ti alloys, as is usual in other alloys. For enhanced strength without ductility reduction, grain refinement and tensile properties were investigated as functions of thickness reduction of cold rolling and annealing condition in Ti-15V-3Cr-3Sn-3Al alloy with a ${\beta}$ single phase. The average grain size of the specimen, which was cold-rolled by 90% and annealed at 700$^{\circ}C$ for 5 min, was decreased to approximately 19 ${\mu}m$. The grain refinement of 63 μm to 19 ${\mu}m$ increased yield stress by 90 MPa without a significant decrease in total elongation. The Ti-15-3 alloy exhibited very low work hardening during tensile test at a crosshead speed of 2 mm/min. This result was discussed based on dynamic recovery associated with dislocation annihilation in grain boundaries.

• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.59-67
• /
• 2016

The automotive manufactures increase their use of lightweight materials to improve fuel economy and energy usage has a significant influence on the choice of developing materials. To meet this requirements manufacturers are replacing individual body parts with lightweight metals, for these the process treating and painting surfaces is changing. The pre-coated steels are newly developed to avoid the conventional complex and non-environmental painting process in the body-in-white car manufacturing. The development of new joining techniques is critically needed for pre-coated steel sheets, which are electrically non-conductive materials. In the present study, dissimilar combination of pre-coated steel and galvanized steel sheets were joined by the self-piercing rivet, adhesive bonding and hybrid joining techniques. The tensile shear test and free falling high speed crash test were conducted to evaluate the mechanical properties of the joints. The highest tensile peak load with large deformation was observed for the hybrid joining process which has attained 48% higher than the self-piercing rivet. Moreover, the hybrid and adhesive joints were observed better strain energy compared to self-piercing rivet. The fractography analyses were revealed that the mixed mode of cohesive and interfacial fracture for both the hybrid and adhesive bonding joints.

• Composites Research
• /
• 제29권2호
• /
• pp.53-59
• /
• 2016

항공기 날개 구조물은 유체를 포함한 연료탱크로 사용되며, 연료탱크와 날개구조물을 연결하는 체결부는 복합재 구조물을 사용한다. 항공기 날개 구조물에 고속의 물체가 관통 또는 폭발하게 되면 수압램 현상이 발생하며, 수압램 현상에 의해 연료탱크에 높은 압력이 생성된다. 이러한 높은 앞력은 날개구조물 뿐만 아니라 연료탱크와 체결부의 파손을 야기하기 때문에 전투용 항공기의 기체 생존성 확보를 위해서는 수압램 효과에 대한 체결부의 거동을 확인해야 한다. 본 연구에서는 수압램 검증 시험에 앞서 항공기의 복합재 날개 외피와 스파 체결부를 모사한 4종류의 복합재 T-Joint에 정적 인장 시험을 수행하여 시편의 파손 거동을 스트레인 게이지와 초고속 카메라를 통해 확인하였다. 스트레인 게이지를 통해 얻은 변형률을 기준으로 동일한 형상과 하중 조건을 갖는 유한요소해석 모델링의 해석 결과를 비교하여 모델링의 타당성을 확인하였으며, 정적 하중에서 복합재 T-Joint의 파손응력을 확인하였다. 유한요소해석을 통해 향후 진행될 수압램 시험에서 각 시편이 파손되는 압력을 예측하였다.

• Advanced Composite Materials
• /
• 제18권4호
• /
• pp.395-413
• /
• 2009

Impact tests on high-strength membrane materials under biaxial loads were experimentally conducted in order to evaluate influence of biaxial loads on impact fracture of the membrane materials for the inflated applications. Cruciform specimens of the membrane materials were fabricated for applying biaxial loadings during the impact test. A steel ball was shot using a compressed nitrogen gas gun, and struck the membrane specimen. Impact tests on uniaxial strip specimens were also conducted to obtain the effect of specimen configuration and boundary condition on the impact fracture. The results of the measured crack length and the ultra-high speed photographs indicate the impact fracture properties of the membrane fabrics under biaxial loadings. Crack length due to the impact increased with applied tensile load, and the impact damages of the cruciform membrane materials under biaxial loadings were smaller than those of under uniaxial loadings. Impact fracture of the strip specimen was more severe than that of the cruciform specimen due to the difference of boundary conditions.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.11-18
• /
• 2014

This research was conducted as a fundamental study to apply tailored blank welding technique into automotive production process. Specially we tried to apply the TWB technique to exhaust system. The materials used in this work were ferritic 439 stainless steel sheet with a thickness of 1.2mm and 0.8mm. Welding tests were conducted for BOP test and dissimilar thickness (0.8 to 1.2t) cases. Major process parameters were position of focus, travel speed, shielding gas and joint (gap) condition. As a result, there are nothing significant welding characteristic compare with TWB of carbon steel. Stainless steel shows the good weldability and mechanical properties (tensile, hardness and forming strength) also shows high level. Just problem is gap condition. However, also in this case, it shows not only good forming strength but also base metal fracture after tensile test. And to conclude, it is good opportunity to make lightweight design muffler using TB welding technique.

• 소성∙가공
• /
• 제15권2호
• /
• pp.132-137
• /
• 2006

This paper is concerned with the thermo-mechanical behavior including temperature dependent strain-rate sensitivity of steel sheet for an auto-body. In order to identify the temperature dependent strain-rate sensitivity of SPRC35R and SPRC45E, uniaxial tension tests are performed with the variation of the strain-rates from 0.001 /sec to 200 /sec at environmental temperatures varied from $-40^{\circ}C\;to\;200^{\circ}C$. The thermo-mechanical response at the quasi-static state is obtained with the static tensile test and at the intermediate strain-rate is from the high speed tensile test. Experimental results show that the strain-rate sensitivity increases at low temperature. It represents that as the strain-rate increases, the variation of flow stress becomes sensitive on the temperature. The results indicate that the flow stress of SPRC35R is more dependent on the changes of strain-rate and temperature than those of SPRC45E.

• 해양환경안전학회지
• /
• 제18권3호
• /
• pp.273-278
• /
• 2012

선박 구조재료 FRP 재료의 대체 재료로 빠른 선속과 선적량 증가는 물론 재활용이 용이한 Al 선박으로 전환되고 있다. 본 논문에서는 인장실험을 통해 레저선박에 사용되는 5456-H116 합금에 대한 최적의 마찰교반용접 조건에서 프루브 직경의 효과를 기술하였다. 마찰교반용접에서 이송속도, 회전속도를 변수로 5 mm의 프루브 직경을 사용하여, 이송속도가 61 mm/min의 조건에서 가장 우수한 결과를 나타냈다. 프루브 직경 6 mm, 회전속도 170-210 rpm, 이송속도 15 mm/min 에서는 낮은 회전속도로 인하여 불충분한 용접열이 발생하여 거친 표면과 기공이 형성 되었다. 회전속도 500-800 rpm인 경우, 용접부에 칩이 관찰되었으며, 기공은 생기지 않았고, 용접표면은 우수하였으나 1100-2500 rpm에서는 지나친 용접열의 발생으로 많은 칩이 발생하였다. 열에 의한 영향은 용접 배면에서 관찰되었다. 이송속도가 15 mm/min에서 회전속도의 증가하게 되면 마찰이 증가함에 따라 용접열이 발생한다. 기계적 특성은 용접 입열량이 증가할수록 재질의 연화가 가속화되어 저하하였다.

• 터널과지하공간
• /
• 제21권2호
• /
• pp.109-116
• /
• 2011

본 연구에서는 스플릿 홉킨슨 압력봉 실험장비를 적용한 압열인장 실험을 수행하여, 암석의 동적인장강도 및 변형률 속도를 평가하였다. 시료가 파괴되기 전에 시료 내 동적 응력평형상태를 확보하기 위하여 펄스쉐이핑 기법으로 입사파의 증가시간을 제어하였다. 압열인장 실험시료는 Inada 화강암, Kimachi 사암, Tage응회암을 정밀하게 가공하여 제작되었다. 결과로서, Inada 화강암의 동적인장강도는 정적인장강도의 11.9배 이였으며, Kimachi 사암과 Tage 응회암은 각각 8.5배, 9.2배로 평가되었다. 고속카메라를 이용하여 시료 내 축 하중 방향으로 발생하는 인장균열의 발생양상을 관찰하였다.

• 한국해양공학회지
• /
• 제29권3호
• /
• pp.241-248
• /
• 2015

A subsea pipeline for oil/gas transportation or gas injection is subjected to extreme variations in internal pressure and temperature, which can involve a strain rate effect on the pipeline material. This paper describes the flow stress characteristics of a pipeline material called API 5L X52N PSL2, using and experimental approach. High-speed tensile tests were carried out for two metal samples taken from the base and weld parts. The target temperature was 100℃, but two other temperature levels of –20℃and 0℃ were taken into account. Three strain rates were also considered for each temperature level: quasi static, 1/s, and 10/s. Flow stress data were proposed for each temperature level according to these strain rates. The dynamic hardening behaviors of the base and weld metals appeared to be nonlinear on the log-scale strain rate axis. A very high material constant value was required for the Cowper-Symonds constitutive equation to support the experimental results.

• 한국레이저가공학회지
• /
• 제8권3호
• /
• pp.11-19
• /
• 2005

In automotive industry, light weight vehicle is one of issues because of the air pollution and the protection of environment. Therefore, automotive manufacturers have tried to adopt light materials such as aluminum alloy to production line. Aluminum welding using laser has some advantages high energy density and high productivity. It is very important to understand weld characteristic according to welding condition in order to determine the possibility of application to car body. In this study, Nd:YAG laser welding of 5182 aluminum alloy with filler wire AA5356 was carried out through experimental design according to wire feed rate, laser power and welding speed. Weld bead shape in terms of cross section photo, bead with, height of reinforcement and penetration depth and mechanical property in terms of tensile strength and formability was investigated. Analysis of variation (ANOVA) was performed to know the effect of weld parameter for weldability, laser power was statistically most significance factor of three variables.