• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2274-2277
• /
• 2003

A cylindrical permanent magnet inside the four-phase permanent magnet (PM) stepping motor is employed as the rotor. The stator has four teeth around, which its coils are wound. The mode of excitation can be classified into 3 modes: single-phase excitation, two-phase excitation and ministep excitation. The ministep drive is a method to subdivide one step into several small steps by means of electronics. The paper presents the programmable ministep technique drive. This technique decodes the results obtained from the counter to locate the data in Read Only Memory (ROM). The Sinusoidal Pulse Width Modulation (SPWM) is transformed to binary file and saved to the ROM. The experiment is performed with the four-phase PM stepping motor and drives from a two-phase programmable sinusoidal ministep signal, instead of square wave. The results show that the performances of the proposed programmable ministep technique drive have high efficiency, smooth step motion, and high speed response. Moreover, the resolution of sinusoidal ministep signal can be controlled by the input frequency (f command).

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.348-355
• /
• 2016

Precision motion stages used in the manufacturing process of flat-panel displays have inevitably low settling performance due to their huge mass and bulky structures. In order to improve the settling performance, several methods of frame vibration compensation have been developed so far. These methods are used to cancel the vibration by imposing a counter force or modifying the resonance mode of the frame of the stage. To compensate the frame vibration, high force actuators are required. In this paper, a mighty voice coil actuator is proposed to generate the counter force against the frame vibration. The proposed voice coil actuator has an axis-symmetric rectangular structure to achieve a large force with simple and low cost fabrication. Also, the voice coil actuator allows radial clearance up to ${\pm}4mm$. Using an optimized design process and a magnetic circuit model, the power consumption is minimized while the required force is obtained. With a power of 322 W, the VCA has been designed to have a maximum force of 574 N with a force constant of 164 N/A. Experimental results verified the force constant of the fabricated voice coil actuator is well matched with the designed value.

• 한국전자파학회지:전자파기술
• /
• 제4권3호
• /
• pp.18-29
• /
• 1993

장거리 초고속 단일모드 광파이버 전송 시스템에서, 색분산은 복조된 파형의 찌그러짐을 생기게 하며, 그 결과 수신된 신호 간 간섭을 일으켜 전송 시스템의 성능을 저하시킨다. 본 논문에서는 강도변조-직접검파 시스 댐의 색분산제한을위상변조에서 진폭변조로의 전환잡음의 영향을고려함으로서 연구하였다. 파이버 색분산에 의한 위상-진폭으로의 전환잡음을 잡음전력 스펙트럼 밀도를 유도함으로서 분석하였으며 위상-진폭 전환잡음을 피하기 위한 시스댐 전력손실과 레이저 선폭에 대한 요구조건을 수치해석을 통하여 구하였다.

• 한국항공우주학회지
• /
• 제39권10호
• /
• pp.919-926
• /
• 2011

고속 비행체의 날개 구조물은 스킨과 튼튼한 골격으로 구성되어 있다. 플러터 해석시 날개 구조물의 고유진동모드를 이용하여 비정상공기력을 계산하고 모달접근법을 이용하여 시간영역이나 주파수 영역에서 구조물의 진동안정성을 분석하게 되므로, 사용되는 고유 진동 모드는 신중하게 선정되어야 한다. 이를 위해 날개 구조물과 같이 고차에서 스킨의 국부진동모드가 있는 경우 이러한 모드가 비정상공기력 및 플러터 특성에 미치는 영향을 분석하였다.

• 한국음향학회지
• /
• 제18권5호
• /
• pp.52-57
• /
• 1999

고속 데이타를 전송하기 위하여 높은 스펙트럼 효율의 QAM 변조기를 설계하는 것은 매우 중요하다. 본 논문에서는 대표적인 16-QAM 변조기를 직접 디지탈 주파수 합성기(DDFS)를 응용하여 설계하였다. 직접 디지탈 주파수 합성기는 외부 주파수 설정에 의해 디지탈 방식으로 원하는 주파수의 정현파를 출력한다. 발생되는 위상 증가 값을 제어하여 정확한 위상변조를 할 수 있으며, 진폭 성분의 변화는 D/A 컨버터의 출력에서 발생하는 진폭을 변화시켜 진폭 변조하여, 전체적인 QAM 변조기를 설계한다. glitch와 같은 고조파 성분의 억제를 위하여 DDFS를 이중구조 형태로 설계하여 개선된 출력파형을 확인하였다. 회로 설계는 P-SPICE를 사용하였다. 아날로그 디지탈 혼합모드로 시뮬레이션하여 16-QAM 변조 파형을 확인하였고, 출력 데이터의 성상도를 출력하여 설계되어진 결과를 확인하였다.

• 한국지구과학회지
• /
• 제36권5호
• /
• pp.419-426
• /
• 2015

We investigated the high dispersion spectra that had been secured at the center of the planetary nebula NGC 7027 with the Bohyunsan Optical Echelle Spectrograph (BOES) on October, 20, 2009. We analyzed the forbidden lines of [OI], [SII], [OII], [NII], [ClIII], [ArIII], [OIII], [ArIV], [NeIII], [ArV], and [CaV] in the $3770-9225{\AA}$ wavelength region. The expansion velocities were derived from double Gaussian line profiles of the emission lines, after eliminating the subsidiary line broadening effects. The radial variations of the expansion velocities were obtained by projecting the derived expansion velocities: $19.56-31.93kms^{-1}$ onto the equatorial shell elements of the inner and the outer boundaries of the main shell of 2.5(2.1)" and 3.8(3.6)", according to the ionization potential of each ion. Analysis of equatorial shell spectra indicated that the equatorial shell generally expands in an accelerated velocity mode, but the expansion pattern deviates from a linear velocity growth with radial distance. NGC 7027, of which age is about 1000 years or less, might be still at its early stage. During the first few hundred years, plausibly in its early stage, the main shell of PN expands very slowly and, later, it gradually gain its normal expansion speed.

• 한국레이저가공학회지
• /
• 제17권4호
• /
• pp.14-19
• /
• 2014

Laser beam was applied on the boundary of the polyurethane and biodegradable polyacetate polymers. The distributed laser passed through the polyurethane layer and heated the polyacetate layer, then the soften acetate was squeezed thorough the 1mm square slots of polyurethane for the mechanical joining. The surface roughness ranging between $0.28{\mu}m$ and $3.06{\mu}m$ had almost no effect on joining strength, but the optical properties of HD (High Definition) and UHD (Ultra High Definition) mode affected laser beam transmittance. The optimum laser power was found to be between 8watt and 10watt with 500mm/min of scanning speed. The joining boundary was characterized by optical and SEM analysis. Based on the experiment and characterization results, the laser energy was effective for the polymer joining and efficiency of joining.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권10호
• /
• pp.1011-1016
• /
• 2015

Gas piping systems in power plants and factories are always influenced by the mechanical vibrations of rotational machines such as pumps, blowers, and compressors. Unusual vibrations in a gas piping system influence possible leakages of liquids or gases, which can lead to large explosive accidents. Real-time measurements of unusual vibrations in piping systems in situ prohibit them from being possible leakages owing to the repeated fatigue of vibrations. In this paper, a non-contact 3-dimensional measurement system that can detect the vibrations of a solid body and monitor its vibrational modes is introduced. To detect the displacements of a body, a stereoscopic camera system is used, through which the major vibration types of solid bodies (such as X-axis-major, Y-axis-major, and Z-axis-major vibrations) can be monitored. In order to judge the vibration types, an artificial neural network is used. The measurement system consists of a host computer, stereoscopic camera system (two-camera system, high-speed high-resolution camera), and a measurement target. Through practical application on a flat plate, the measured data from the non-contact measurement system showed good agreement with those from the original vibration mode produced by an accelerator.

• 정보와 통신
• /
• 제16권10호
• /
• pp.112-124
• /
• 1999

본 논문에서는 FTTC/VDSL (Fiber-to-the-Curb/Very High-speed Digital Subscriber Line) 전송시스템의 개발동향과 ANSI, ETSI, ITU등의 표준화 위원회에서 현재 진행중인 VDSL 시스템의 표준화 작업에 대해 기술하였다. 특히, POTS (Plain Old Telephone Service), BA-ISDA(Basic Access Integrated Services Digital Network), HDSL(High-rate Digital Subscriber Line), SDSL (Single-pair HDSL), ADSL(Asymmetric Digital Subscriber Line) 등의 다양한 xDSL (Digital Subscriber Line) 서비스들에서 발생하는 NEXT (Near-end Crosstalk)/FEXT (Far-end Crosstalk)와 같은 crosstalk를 최소화하기 위해 제안된 VDSL시스템의 주파수 대역과 PSD (Power Spectral Density) mask에 관해 설명하고, 순방향(down-stream) 채널과 역방향(upstream) 채널의 데이터 전송률이 대칭적인 VDSL전송시스템과 비대칭적인 VDSL 전송시스템 간의 주파수대역의 호환성 문제, RFI(Radio Frequency Interference) ingress/egress 문제의 해결 방안에 관해 기술하였다. 또한, 현재 VDSL Coalition과 VDSL Alliance 간에 논의 중인 VDSL 전송시스템의 변복조 방식에 관한 표준화 작업과정 및 순방향과 역방향에 할당될 band 개수에 따른 시스템 성능의 장단점 등에 관해 살펴보았다. 끝으로 현재 국내에서 개발되고 있는 FTTC/VDSL 전송시스템의 전체구조를 요약하고, 네트워크에서 가입자쪽으로 순방향 데이터 전송에 사용된 51.84 Mb/s 19-CAP (Carrierless Amplitude/Phase Modulation) 전송시스템과 가입자 댁내에서 네트워크 방향으로 역방향 데이터 전송에 사용된 1.62 Mb/s QPSK (Quadrature Phase Shift Keying) burst-mode TDMA (Time Division Multiple Access) 전송시스템 등의 동작 원리 및 구조를 기술하였다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 Proceedings of 2004 Korea-Japan Joint Seminar on Particle Image Velocimetry
• /
• pp.125-134
• /
• 2004

The improvement of artificial respiration method has brought about the decrease in mortality of pulmonary diseases patients. Various respiratory curative methods, inclusive of HFOV (High Frequency Oscillatory Ventilation), have been developed for more effectual and less harmful management of acute respiratory failure. However, the mechanism of gas transfer and diffusion in a bronchiole has not yet been clarified in detail. As a first approach to the problem, we measured oscillatory flows in a Y-shaped micro-channels as bronchiole model by micro Particle Image Velocimetry(micro PIV). In order to establish the fundamental technique of PIV measurements on oscillatory air flow in a micro-channel, we used about 500-nm-diameter incense smoke particles, a diode laser, a high speed camera including an objective lens, and a HFOV, which is effective technique for medical care of pulmonary disease patients, especially, infants. The bronchiole model size is that parent tube is $500\{mu}m$ width and $500\{mu}m$ depth, and daughter tubes are $450\{mu}m$ width and $500\{mu}m$ depth. From this study made on the phenomenon of fluid in micro size bronchus branch of a lung, we succeeded to get time series velocity distribution in a micro scale bronchial mode. The experimental results of velocity distribution changing with time obtained by micro PIV can give fundamental knowledge on oscillatory airflow in micro-channel.