• Journal of the Korea Concrete Institute
• /
• v.16 no.2 s.80
• /
• pp.283-291
• /
• 2004

Recently, the construction of underwater structures has been gradually increased, but underwater concrete got some problems of quality deterioration and water contamination around cast-in-situ of construction. In addition, massive underwater structures such as LNG tank, underwater concrete structures of large and continuous high- strength subterranean wall under water are being demanded lower heat of hydration. In this paper, the mechanical properties of high-strength antiwashout underwater concrete (HAWC) containing with two kinds of mineral admixtures respectively were investigated. On the basis of these results, the pH value and suspended solids of HAWC manufactured in the mock-up test were 10.0$\Box$11.0 and 51 mg/${\iota}$ at 30 minutes later, respectively, initial and final setting time were about 30,37 hours, and the slump flow was 530$\pm$20Tm. In the placement at a speed of $27 m^3/hr$, there was no large difference in flowing velocity with or without reinforcing bar, and flowing slope was maintained at horizontal level. Compressive strength and elastic modulus of the cored specimen somewhat decreased as flowing distance was far; however, those of central area showed the highest value.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.531-541
• /
• 2009

The research analyzes and investigates conventional concrete, hydration heat, set, and mechanical properties by making high flowing self-compacting concretes of binary blend and ternary blend as one of evaluations about the properties of the hydration heat of high flowing self-compacting concrete with a strength of 30, 50, and 70 MPa. In addition, it estimates concrete adiabatic temperatures by calculating a thermal property value of powder obtained by measuring a heat evolution amount for powder used in concrete, a thermal property value of concrete obtained by conducting a simple adiabatic temperature test, and a normal thermal property value of material used in concrete, using a simple equation. Moreover, it analyzes and investigates the hydration heat property of high flowing self-compacting concrete and the thermal stress caused by hydration heat by conducting a 3D temperature stress analysis for the hydration heat and the adiabatic temperature obtained by temperature analysis, using MIDAS CIVIL 06 program.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.112-116
• /
• 1996

This experimental study was performed to produce high flowing nomal strength concrete using viscosity agent. Test variables were selected to the viscosity agent contents with 4 levels, the cement contents with 5 levels and the coarse aggregate contents with 3 levels, etc. As a result, the high flowing and filling properties of concrete were obtatined by proper amount of viscosity agent and superplasticizer in the normal strength concrete. For the concrete mix proportions, it was found that unit weight of cement was more than 364kg/㎥ and volume of coarse aggregate was less than $280\ell/\textrm{m}^3$ in this study.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.33-36
• /
• 1998

Generally, the base concrete for manufacturing the flowing concrete has to increase the fine aggregate content or adjust the fines content prevent the concrete from segeration, However, it may not only increase the cost, but cause the inconvenience in production of base concrete. In this paper, the experiments is performed on the superplasticizer which is used for base concrete by mixing viscosity agents and AE admixtures. According to the results, it shows that it is possible to manufacture a flowing, non segregation, high durability and economical concrete in the field without increasing the fine aggregate content of base concrete, when the superplasticizer are mixed with viscosity agents and AE admixtures in an appropriate proportion.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.293-296
• /
• 2001

This paper presents the results of field application test on the manufacturing of high fluidity concrete by applying flowing methods with segregation reducing type superplasticizer. Base concrete is made with 20% of fly ash, which is flowed during the transportation. According to test results, fluidity, placeability and segregation reducing performance meet the range of high fluidity concrete after flowing, while air loss occurs due to fly ash. There are no noticeable differences in compressive strengths between non-compacting and compacting methods. According to non-destructive tests with rebound and core strength test, we cannot detect any differences in strength according to the height in the structures.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.3
• /
• pp.135-146
• /
• 1996

In this study, the properties of super flowing concrete containing fly ash were experimentally investigated and compared with those of ordinary concrete. Tests were carried out on five types of super flowing concrete mixes containing fly ash and three types of ordinary concrete mixes without fly ash. Flow test, 0-funnel test, box test, L type test and slump test were carried out to obtain the properties for flowability and workability of fresh concrete. The mechanical properties of hardened concrete were also investigated in terms of compressive strength, splitting tensile strength, modulus of elasticity, creep and drying shrinkage. In fresh concrete, it was found that super flowing concrete had excellent workability and flowability compared with ordinary concrete, and had self-compactable performance. Super flowing concrete *also had good mechanical properties at both early and late ages with compressive strength reaching as high as 40 MPa at 28 days. The creep deformation of super flowing concrete investigated was relatively lower than that of ordinary concrete, but drying shrinkage was much higher.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.89-92
• /
• 2006

To investigate the properties of high flowing and high strength concrete with crushed sand and fly ash for CFT structure, many batches were performed by a trial-error method. In the experiment W/B was set up three levels as 0.25, 0.30 and 0.35. Also the variables of the experiment were a substitution ratio of fly ash, a blend ratio of crushed sand and the ages of specimens(3, 7, 28 days). The results of this study are summarized as the follows; 1) The effect a substitution ratio of fly ash on the compressive strength was not consistent with age. For twenty-eight day compressive strength, the best result was come out when cement was substituted by 10% of fly ash. 2) The decrease of the water binder ratio, the increase of compressive strength and elastic modulus. Also the relationship is very similar to the case of a normal concrete

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.63-72
• /
• 2012

The high-flowing concrete requires additionally or excessively more expensive admixture than conventional concrete. So, the concrete has not to be widely used in practical field due to the increase of production price, need of additional facilities, and excessive development of concrete strength in associate with addition of too much cementitious material even though it has more significant advantages than conventional concrete. Thus, this study aims at developing high-flowing concrete with general strength unlike high strength which has been carried out in conventional study. To observe the role of aggregate in the concrete quantitatively and to increase the performance of high-flowing concrete effectively, parametric studies were carried out such as W/C, s/a, fineness modulus of aggregate, contribution degree of particle sizes, and the effect of 13mm aggregate and fine stone powder as a partial replacement of aggregates. And the effect of these factors on performance of the concrete was evaluated by measuring slump-flow and gap of penetration height in U-typed instrument. As a result, it was found that flowability of high-flowing concrete depends upon grading of fine aggregate more significantly than that of coarse aggregate and is enhanced greatly as fineness modulus of fine aggregate decreases and the value of s/a increases. In addition, the application of 13mm aggregate and fine stone powder are expected as a partial replacement of aggregate in order to increase the performance of high-flowing concrete more effectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.567-572
• /
• 2002

This research investigates experimentally an effect on the quality performances of the high flowing concrete according to binder types. The purpose of this study is to determine the optimum mix proportion of the high flowing concrete having good flowability, viscosity and no-segregation. For this purpose, two types using belite cement＋lime stone powder(LSP) and furnace slag cement+lime stone powder are selected and tested by design factors including water cement ratio, fine and coarse aggregate volume ratio. As test results of this study, the optimum mix proportion for binder types is as followings. 1) One type based belite cement ; water cement ratio $51^{\circ}C$, fine aggregate volume ratio $43^{\circ}C$ and coarse aggregate volume ratio $53^{\circ}C$, replacement ratio of LSP $42.7^{\circ}C$. 2) Another type based slag cement : water cement ratio $41^{\circ}C$, fine aggregate volume ratio $47^{\circ}C$ and coarse aggregate volume ratio $53^{\circ}C$, replacement ratio of LSP $13.5^{\circ}C$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.93-96
• /
• 2006

To investigate the properties of high flowing concrete with fly ash and crushed sand for CFT structure, many batches were performed by a trial-error method and the results were analyzed by SPSS software program. In the experiment W/B was set up as 0.25 and the variables were a substitution ratio of fly ash, a blend ratio of crushed sand and the ages of specimens (3, 7, 28 days). The results of this study are summarized as the follows; 1) The increase of the substitution ratio of fly ash, the decrease of dosage of SP and the increase of dosage of AEA due to very fine sphere particle of fly ash. 2) The increase of the blend ratio of crushed sand, the increase of dosage of S/a and water content related with viscosity. 3) Made the high flowing concrete, the increase S/a and the increase the water content.