• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.380-393
• /
• 2019

Traditional boost converters have difficulty realizing high efficiency and high voltage gain conversion due to 1) extremely large duty cycles, 2) high voltage and current stresses on devices, and 3) low conversion efficiency. Therefore, a function decoupling high voltage gain DC/DC converter composed of a DC transformer (DCX) and an auxiliary converter is proposed. The role of DCX is to realize fixed gain conversion with high efficiency, whereas the role of the auxiliary converter is to regulate the output voltage. In this study, different forms of combined high voltage gain converters are compared and analyzed, and a structure is selected for the function decoupling high voltage gain converter. Then, topologies and control strategies for the DCX and auxiliary converter are discussed. On the basis of the discussion, an optimal design method for circuit parameters is proposed, and design procedures for the DCX are described in detail. Finally, a 400 W experimental prototype based on the proposed optimal design method is built to verify the accuracy of the theoretical analysis. The measured maximum conversion efficiency at rated power is 95.56%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.127-132
• /
• 2018

In this paper, a high conversion gain cascode mixer was designed in W-band and verified by the fabrication and measurements. In the high frequency band such as a W-band, the conversion loss of a mixer is increased because of the poor performance of transistors. This high conversion loss of the mixer requires additional circuits which can give an extra gain such as an RF buffer amplifier, and this can affects the linearity and stability of the overall systems. Therefore, it is necessary to maximize the conversion gain of the mixer. To maximize the conversion gain of the mixer, biases of the transistor were optimized, and output load impedance was optimized by the load-pull simulations. The designed mixer was fabricated in $0.1-{\mu}m$ GaAs pHEMT technology and verified by the measurements. The measurement results shows a maximum conversion gain of -4.7 dB at W-band and an input 1-dB compression point of 2.5 dBm.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.408-412
• /
• 2018

In this paper, a 26GHz variable gain amplifier fabricated using a 40nm CMOS process is studied. In the case of an automobile radar using 79 GHz, it is advantageous in designing and driving to drive down to a low frequency band or to use a low frequency band before up conversion rather than designing and matching the entire circuit to 79 GHz in terms of frequency characteristics. In the case of a Phased Array System that uses time delay through TTD (True Time Delay) in practice, down conversion to a lower frequency is advantageous in realizing a real time delay and reducing errors. For a VGA (Variable Gain Amplifier) operating in the 26GHz frequency band that is 1/3 of the frequency of 79GHz, VDD : 1V, Bias 0.95V, S11 is designed to be <-9.8dB (Mea. High gain mode) and S22 < (Mea. high gain mode), Gain: 2.69dB (Mea. high gain mode), and P1dB: -15 dBm (Mea. high gain mode). In low gain mode, S11 is <-3.3dB (Mea. Low gain mode), S22 <-8.6dB (Mea. low gain mode), Gain: 0dB (Mea. low gain mode), P1dB: -21dBm (Mea. Low gain mode).

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.113-114
• /
• 2006

In this paper, dual-gate mixer has been designed and optimized to have variable conversion gain for WiBro and WLAN applications and to save power. With the LO power of 0dBm and RF power of -50dBm, the mixer shows 15dB conversion gain. When RF power increases from -50dBm to -20dBm, the conversion gain decreases to -2dB with bias change. The variable conversion gain can reduce the high dynamic range requirement of AGC burden at IF stage. Also, it can save the dc power dissipation of mixer up to 90%.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.161-165
• /
• 2011

In this paper, a high-efficiency DC-AC converter is used for wireless energy transmission. The DC-AC convertter is implemented by combining the oscillator and power amplifier. Given that the conversion efficiency of a DC-AC converter is strongly affected by the efficiency of the power amplifier, a high-efficiency power amplifier is implemented using a class-E amplifier structure. Also, because of the low output power of the oscillator connected to the input stage of the power amplifier, a high-gain two-stage power amplifier using a drive amplifier is used to realize a high-output power DC-AC converter. The high-efficiency DC-AC converter is realized by connecting the oscillator to the input stage of the high-gain high-efficiency two-stage class-E power amplifier. The output power and the conversion efficiency of the DC-AC converter are 40.83 dBm and 87.32 %, respectively, at an operation frequency of 13.56 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• Journal of Power Electronics
• /
• v.19 no.3
• /
• pp.676-690
• /
• 2019

This paper presents a switched capacitor (SC) based bidirectional dc-dc converter topology for high voltage gain applications. The proposed converter is able to operate with multiple integral voltage conversion ratios based on user input. The architecture of a user-friendly, inductor-less multi-voltage-gain bidirectional dc-dc converter is proposed in this study. The inductor-less or magnetic-less design of the proposed converter makes it effective in higher temperature applications. Furthermore, the proposed converter has a reduced component count and lower voltage stress across its switches and capacitors when compared to existing SC converters. An output impedance analysis of the proposed converter is presented and compared with popular existing SC converters. The proposed converter is simulated in the OrCAD PSpice environment and the obtained results are presented. A 200 W hardware prototype of the proposed SC converter has been developed. Experimental results are presented to validate the efficacy of the proposed converter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.522-529
• /
• 2002

MMIC circuits in whole receiver system was fabricated based on GaAs pHEMT technology. And a V-band downconverter module was fabricated by integrating these circuits. The downconverter module consists of a LO drive power amplifier which generates 24dBm output power, a low noise amplifier(LNA) which shows 20 dB small signal gain, an active parallel feedback oscillator which generates 1.6 dBm output power, and a cascode mixer which shows over 6dB conversion gain. The good conversion gain performance of our mixer made no need to attach any IF amplifier which grows conversion gain. Measured results of the complete downconverter show a conversion gain of over 20 dB between 57.5 GHz and 61.7GHz without IF amplifier.

• Journal of Advanced Navigation Technology
• /
• v.10 no.2
• /
• pp.138-144
• /
• 2006

In this paper, dual mode FET mixer for WiBro and wireless LAN(WLAN) applications has been designed in the form of dual gate FET mixer by using the cascode structure of two single gate pHEMTs. The designed dual gate mixer has been optimized to have variable conversion gain for WiBro and WLAN applications in order to save dc power consumption. The LO to RF isolation of the designed mixer is more than 20dB from 2.3GHz to 2.5GHz band. With the LO power of 0dBm and RF power of -50dBm, the mixer shows 15dB conversion gain. When RF power increases from -50dBm to -20dBm, the conversion gain decreases to -2dB from 15dB with bias change. The variable conversion gain has several advantages. It can reduce the high dynamic range requirement of AGC burden at IF stage. Also, it can save the dc power dissipation of mixer up to 90%.

• Journal of the Optical Society of Korea
• /
• v.13 no.2
• /
• pp.256-260
• /
• 2009

The optical performance of the reflective polarizer was investigated over three kinds of direct-lit backlights and/or different configurations of the optical sheets. The optical gain factor achieved by using the reflective polarizer increased as the diffuse nature of the optical sheet was enhanced, because of the more efficient polarization conversion. In addition, the gain factor decreased substantially in flat-lamp backlights compared to tubular-lamp backlights, which was ascribed to the high loss factor during the polarization recycling process due to the complex structure and large area of flat lamps. All these results suggested that reducing the loss factor of the backlight is very important for efficient polarization conversion and thus high optical gain of the reflective polarizer.