• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.3
• /
• pp.88-94
• /
• 1993

In this paper, a simple Ebers-Moll Model for the heterojunction bipolar transistor is presented. Using the model structure for the npn type HBT, the current-voltage characteristics was analyzed. And from the obtained terminal currents, the Ebers-Moll equations were derived. Then substituting the physical parameters for heterojunction to those for homojunction, this model would be used to analyze the characteristics of single and/or duble heterojunction HBT's. And directly relating model parameters to device parameters, it would be also used to optimize the characteristics of HBT's. The simulated results using this model were in good agreement with experimental data.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.49-52
• /
• 2002

A new method is developed to extract model parameters of SiGe HBT equivalent circuit including the base impedance and base-collector junction capacitance. Using this method, all resistances and capacitances of SiGe HBT are independently determined from measured S-parameters using two-port parameter formula. This method is proposed to reduce possible errors generated from global optimization process, and its accuracy has been verified by finding good agreements between measured and modeled current / power gain up to 18 GHz.

• ETRI Journal
• /
• v.26 no.1
• /
• pp.61-64
• /
• 2004

We have explored the fabrication of an InP/InGaAs single heterojunction bipolar transistor (HBT) and a wave guide p-i-n photodiode (PD) on two kinds of double stacked layers for the implementation of an optoelectronic millimeter-wave monolithic integrated circuit (OEMMIC). We applied a photosensitive polyimide for passivation and integration to overcome the large difference between the HBT and PD layers of around $3{\mu}m$. Our experiment showed that the RF characteristics of the HBT were dependent on the location of the PD layer, while the dc performances of the HBTs and PDs were independent of the type of stacked layer used. The $F_t$ and $F_{max}$ of the HBTs on the HBT/PD stacked layer were 10% lower than those of the HBTs on the PD/HBT stacked layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.63-66
• /
• 2000

In this paper, we present the simulation of the heterojunction bipolar transistor with different Emitter-Base junction structures. Our simulation results include effect of setback and graded layer. We prove the emitter efficiency's improvement through setback and graded layer. In 1995, the analytical equations of electric field, electrostatic potential, and junction capacitance for abrupt and linearly graded heterojunctions with or without a setback layer was derived. But setback layer and linearly graded layer's recombination current was considered numerically. Later, recombination current model included setback layer and graded layer will be proposed. New recombination current model also wile include abrupt heterojunction's recombination current model. In this paper, the material parameters of the heterojunction bipolar transistor with different Emitter-Base junction structures is introduced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.52-52
• /
• 2009

In this work, we demonstrate the modelling and simulation of the AlGaAs/GaAs quantum-well based light emitting transistor(LET). Based on the experimental and theoretical model, we have compared between a heterojunction bipolar transistor(HBT) structure with quantum wells in the base region and a HBT without quantum wells in the base region. For the purpose of optimizing device design, several analytic and numerical studies have been presented.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.172-175
• /
• 2004

This paper analyzes the effects of Ge profiles shape of SiGe heterojunction bipolar transistors (HBT's) for high frequency application. Device simulations using ATLAS/BLAZE for the SiGe HBT with trapezoidal or triangular Ge profile are carried out to optimize the device performance. An HBT with $15\%$ triangular Ge profile shows higher cut-off frequency and DC current gain than that with $19\%$ trapezoidal Ge profile. The cut-off frequency and DC gain are increased from 42GHz to 84GHz and from 200 to 600, respectively. The SiGe HBT has been fabricated using a production CVD reactor.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.357-360
• /
• 2000

This paper describes a parameter extraction method for HBT(Heterojunction Bipolar Transistor) equivalent circuit model without measurements of special test structures or numerical optimizations. Instead, all equivalent circuit parameters are calculated analytically from small-signal S-parameters measured under different bias conditions. These values being extracted from the cutoff mode can be used to extract intrinsic parameters at the active mode. This method yields a deviation of about 1.3 % between the measured and modeled S-parameters.

• ETRI Journal
• /
• v.27 no.1
• /
• pp.75-80
• /
• 2005

This paper addresses a fully-integrated low phase noise X-band oscillator fabricated using a carbon-doped InGaP heterojunction bipolar transistor (HBT) GaAs process with a cutoff frequency of 53.2 GHz and maximum oscillation frequency of 70 GHz. The oscillator circuit consists of a negative resistance generating circuit with a base inductor, a resonating emitter circuit with a microstrip line, and a buffering resistive collector circuit with a tuning diode. The oscillator exhibits 4.33 dBm output power and achieves -127.8 dBc/Hz phase noise at 100 kHz away from a 10.39 GHz oscillating frequency, which benchmarks the lowest reported phase noise achieved for a monolithic X-band oscillator. The oscillator draws a 36 mA current from a 6.19 V supply with 47.1 MHz of frequency tuning range using a 4 V change. It occupies a $0.8mm{\times}0.8mm$ die area.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.411-414
• /
• 2014

A switch is one of the most useful circuits for controlling the path of signal transmission. It can be added to digital circuits to create a kind of gate-level device and it can also save information into memory. In RF subsystems, a switch is used in a different way than its general role in digital circuits. The most important characteristic to consider when designing an RF switch is keeping the isolation as high as possible while also keeping insertion loss as low as possible. For high isolation, we propose leakage signal cancellation and inductive switching for designing a singlepole double-throw (SPDT) RF switch. By using the proposed method, an isolation level of more than 23 dB can be achieved. Furthermore, the heterojunction bipolar transistor (HBT) process is used in the RF switch design to keep the insertion loss low. It is demonstrated that the proposed RF switch has an insertion loss of less than 2 dB. The RF switch operates from 1 to 8 GHz based on the $0.18-{\mu}m$ SiGe HBT process, taking up an area of $0.3mm^2$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.40-47
• /
• 1998

This paper report sthe design, fabrication and characterization of an AlGaAs/GaAs HBT (heterojunction bipolar transistor) with an air-bridge isolation structure which is made to improve high frequency characteristics for the application to the mobile communication system in the next genration. We found that the size, shape and structure of HBT have an effect on the high frequency operation. The measured dc and ac characteristics of the four type HBTs were compared and analyzed. An E-type HBT with an air-bridge structure by undercut etching exhibited .beta.=56, $V_{off-set}$ = 0.3 V, B $V_{CEO}$=7.0V with $f_{T}$=40 GHz and $f_{max}$=45GHz at a collector current density of 7.1*10$^{4}$ A/c $m^{2}$.>.