• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.156-161
• /
• 2020

In this study, hierarchical mesoporous CuO spheres, ZnO flowers, and heterojunction CuO/ZnO nanostructures were fabricated via a facile hydrothermal method. The as-prepared materials were characterized in detail using various analytical methods such as powder X-ray diffraction, micro Raman spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, and transmission electron microscopy. The obtained results are consistent with each other. The H₂S-sensing characteristics of the sensors fabricated based on the CuO spheres, ZnO flowers, and CuO/ZnO heterojunction were investigated at different temperatures and gas concentrations. The sensor based on ZnO flowers showed a maximum response of ~141 at 225 ℃. The sensor based on CuO spheres exhibited a maximum response of 218 at 175 ℃, whereas the sensor based on the CuO/ZnO nano-heterostructure composite showed a maximum response of 344 at 150 ℃. The detection limit (DL) of the sensor based on the CuO/ZnO heterojunction was ~120 ppb at 150 ℃. The CuO/ZnO sensor showed the maximum response to H₂S compared with other interfering gases such as ethanol, methanol, and CO, indicating its high selectivity.

• Journal of IKEEE
• /
• v.28 no.1
• /
• pp.104-109
• /
• 2024

In this research, we explored the influence of post-annealing atmospheres on the electrical properties of Ga₂O₃/SiC heterojunction diodes. We fabricated Ga₂O₃/SiC heterojunction diodes by RF sputtering and after the fabrication the post-annealing in various gas atmospheres was performed. We measured the changes in deep-level defects using Deep Level Transient Spectroscopy (DLTS) and we conducted an electrical characteristic of J-V measurement and Hall measurement to analyzed the effects of annealing atmosphere on Ga₂O₃/SiC heterojunction diode. In the N₂ annealed devices, the highest on-state current was measured as 3.06 × 10^-2 A/cm^2, and an increase in carrier concentration of 3.8 × 10¹⁴ cm^-3 was observed. This confirms that the variations in deep level defects due to the post-annealing atmosphere can influence the electrical properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.332.2-332.2
• /
• 2016

Two dimensional transition-metal dichalcogenides (TMDs) semiconductors are attractive materials for optoelectric devices because of their direct energy bandgap and transparency. To investigate the feasibility of transparent p-n junctions, we have fabricated a p-n heterojunction consisting of p-type WSe2 and n-type MoS2 flakes since WSe2 and MoS2 with proper electrode metals exhibit p-type and n-type behaviors, respectively. These heterojunctions exhibits gate-tunable rectifying behaviors and photovoltaic effects (ECE ~ 0.2%) indicating that p-n junctions were formed. In addition, photocurrent and photovoltaic effects were observed under light illumination, which were dependent on the gate voltage. In addition, the photocurrent mapping images indicate that the photovoltaic effects comes from the junction area. Possible origins of gate-tunability are discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.144.1-144.1
• /
• 2016

We fabricate organic single crystal nanowire heterojunction p-n diode poly(3-hexylthiophene)(P3HT) and from Phenyl-C61-butyric acid methyl ester(PCBM) using by liquid-bridge mediated nanotransfer molding(LB-nTM) method. LB-nTM has been reported an one step direct printing method for making well-aligned nanowire arrays. Moreover, multi-patterning nanostructures can be fabricated with the consecutive printing process. As a result, it is possible to make simple and basic concept of heterojunction devices such as lateral organic p-n nanojunction diode. P3HT/PCBM nanowires heterojunction diode has rectifying behavior with on/off ratios of ~20.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.177-178
• /
• 2008

열처리 조건이 이종접합 유기태양전제(heterojunction organic photovoltaics)의 power conversion efficiency(PCE)에 미치는 영향에 대해 살펴보았다. 본 연구에서는 열처리 온도와 열처리 시간을 변수로 다양한 조건하에서 유기태양전지를 제작하고 AM1.5G 조건에서의 효율 변화를 관찰하였다. 열처리 온도는 $90^{\circ}C$에서 $170^{\circ}C$까지 변화시키며 태양전지의 특성변주를 측정하였으며, 유리 기판 상에 제작된 태양전지의 경우에 $150^{\circ}C$의 열처리 온도에서 가장 우수한 효율을 나타내었다.

• Current Photovoltaic Research
• /
• v.4 no.2
• /
• pp.48-53
• /
• 2016

We report the effect of physical load on the stability of organic solar cells under physical loads. The active layers in organic solar cells were fabricated with bulk heterojunction films (BHJ) films of poly (3-hexylthiophene) and phenyl-$C_{61}$-butyric methyl ester. The loading time was varied up to 60 s by keeping the physical load constant. Results showed that the open circuit voltage was not influenced by the physical load but other solar cell parameters were sensitive to the loading time. The fill factor was very slightly increased at 15 s, while short circuit current density was well kept for 30 s. The power conversion efficiency was reasonably maintained for 45 s but became significantly decreased by the continuous loading for 60 s.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.11
• /
• pp.720-724
• /
• 2016

Transparent n-type metal-oxide semiconductor of $MoO_x$ was applied on a p-type Si substrate for high-performing heterojunction photodetector. The formation of $MoO_x$ on Si spontaneously established a rectifying current flow with a high rectification ratio of 1,252.3%. Under light illumination condition, n-type $MoO_x$/p-type Si heterojunction device provided significantly fast responses (rise time : 61.28 ms, fall time : 66.26 ms). This transparent metal-oxide layer ($MoO_x$) would provide a functional route for various photoelectric devices, including photodetectors and solar cells.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.289-290
• /
• 2006

We report a study of Zn(S)Se/GaAs heterojunction solar cells grown by molecular beam epitaxy (MBE). Zn(S)Se/GaAs heterostructures prepared under different conditions were characterized in-situ by reflection high-energy electron diffraction (RHEED). Structural and electrical properties were investigated with double crystal X-ray diffraction and current-voltage characteristics, respectively. The fabricated $n-ZnS_{0.07}Se_{0.93}/p-GaAs$ solar cell (SC #2) exhibited open circuit voltage($V_{oc}$) of 0.37 V, short circuit current($I_{sc}$) of $1.7{\times}10^{-2}$ mA, fill factor of 0.62 and conversion efficiency of 7.8 % under 38.5 $mW/cm^2$ illumination.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.114.2-114.2
• /
• 2014

The orientation of the constituent molecules in organic thin film devices can affect significantly their performance due to the highly anisotropic nature of ${\pi}$-conjugated molecules. We report here an angle dependent x-ray absorption study of the control of such molecular orientation using well-ordered interlayers for the case of a bilayer heterojunction of chloroaluminum phthalocyanine (ClAlPc) and C60. Furthermore, the orientation-dependent energy level alignment of the same bilayer heterojunction has been measured in detail using synchrotron radiation-excited photoelectron spectroscopy. Regardless of the orientation of the organic interlayer, we find that the subsequent ClAlPc tilt angle improves the ${\pi}-{\pi}$ interaction at the interface, thus leading to an improved short-circuit current in photovoltaic devices based on ClAlPc/C60. The use of the interlayers does not change the effective band gap at the ClAlPc/C60 heterointerface, resulting in no change in open-circuit voltage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.492-492
• /
• 2014

On account of the good conductivity and optical properties, TCO is generally used in silicon heterojunction solar cell since the emitter material, hydrogenated amorphous silicon (a-Si:H), of the solar cell has low conductivity compare to the emitter of crystalline silicon solar cell. However, the work function mismatch between TCO layer and emitter leads to band-offset and interfere the injection of photo-generated carriers. In this study, work function engineering of TCO by oxygen reactive sputtering method was carried out to identify the trend of band-offset change. The open circuit voltage and short circuit current are noticeably changed by work function that effected from variation of oxygen ratio.