• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1385-1389
• /
• 2005

This paper describes the design, analysis and manufacture procedure of the composite blade for hingeless rotor system of unmanned helicopters. Helicopter rotor system is the key structural unit that produces thrust and control forces for intended flight conditions. In this work, a hingeless rotor system is adopted, and base on the design requirements for rotor system, composite blade section design and calculation of material properties were performed. In order to avoid the unstable state such as resonance, vibration characteristics of rotor system were analyzed. Finally, this paper describes the forming and manufacture of composite blade.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.7
• /
• pp.542-550
• /
• 2018

This paper presents design of a bearingless main rotor of SNUF (Seoul National University Flap) blade equipped with active trailing-edge flap to reduce the hub vibratory loads during helicopter forward flight. For that purpose, sectional design of the flexbeam is carried out using the thin-walled composite material rotating beam vibration analysis program (CORBA77_MEMB) in EDISON. Using the multi-body dynamics analysis program, DYMORE, blade dynamic characteristics and those of the loads control are examined using the active trailing-edge flap in terms of the flexbeam sectional design.

• Advances in aircraft and spacecraft science
• /
• v.1 no.1
• /
• pp.69-91
• /
• 2014

Numerical investigations are presented, which show that a back-flow flap can improve the dynamic stall characteristics of oscillating airfoils. The flap was able to weaken the stall vortex and therefore to reduce the peak in the pitching moment. This paper gives a brief insight into the method of function of a back-flow flap. Initial wind tunnel experiments were performed to define the structural requirements for a detailed experimental wind tunnel characterization. A structural integration concept and two different actuation mechanisms of a back-flow flap for a helicopter rotor blade are presented. First a piezoelectric actuation system was investigated, but the analytical model to estimate the performance showed that the displacement generated is too low to enable reliable operation. The seond actuation mechanism is based on magnetic forces to generate an impulse that initiates the opening of the flap. A concept based on two permanent magnets is further detailed and characterized, and this mechanism is shown to generate sufficient impulse for reliable operation in the wind tunnel.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.4
• /
• pp.614-623
• /
• 2015

When the speed of a coaxial rotor helicopter in forward flight increases, the wake skew angle of the rotor increases and consequently the position of the vena contracta of the upper rotor with respect to the lower rotor changes. Considering ambient air and the effect of the upper rotor, this study proposes a nonuniform inflow model for the lower rotor of a coaxial rotor helicopter in forward flight. The total required power of the coaxial rotor system was compared against Dingeldein's experimental data, and the results of the proposed model were well matched. A plant model was also developed from first principles for flight simulation, unknown parameter estimation and control analysis. The coaxial rotor helicopter used for this study was manufactured for surveillance and reconnaissance and does not have any stabilizer bar. Therefore, a feedback controller was included during flight test and parameter estimation to overcome unstable situations. Predicted responses of parameter estimation and validation show good agreement with experimental data. Therefore, the methodology described in this paper can be used to develop numerical plant model, study non-uniform inflow model, conduct performance analysis and parameter estimation of coaxial rotor as well as other rotorcrafts in forward flight.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.2
• /
• pp.82-90
• /
• 2007

Recently, the development project is conducting disaster effect estimation to breed disaster, and cope these disaster beforehand provoking soil erosion and flood. Therefore, it is important to analyze and reduce of these disaster. In this study, it is intended to extract LS and C factors of soil erosion through the digital image. The photogrammetric technique, which employs the Remote Control Helicopter equipped with a non-metric digital camera, was used for the efficient survey and analysis of cutting slopes. As a result, we obtain more objective value of soil erosion factor using digital image.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.11
• /
• pp.1103-1111
• /
• 2014

The results of control law design for a tilt-rotor unmanned aerial vehicle that has a nacelle mounted wing extension (WE) are presented in this paper. It consists of a control surface mixer, stability and control augmentation system (SCAS), hold mode for altitude / speed / heading, and a guidance mode for preprogram and point navigation which includes automatic take-off and landing. The conversion corridor and the control moments derivatives between the original tilt-rotor and its variant of the nacelle mounted WE were compared to show the effectiveness of the WE. The nacelle conversion of the original tilt-rotor starts when the airspeed is greater than 30 km/h but its WE variant starts at 0 km/h in order to reduce the drag caused by the high incidence angle of the WE. The stability margins of the inner loop are presented with the optimization approach. The outer loops for the hold mode are designed with trial and error methods with linear and nonlinear simulation. The main control parameter for altitude control of the helicopter mode is thrust command and it is transferred to the pitch attitude command in airplane mode. Otherwise, the control parameter for the speed of the helicopter mode is the pitch attitude command and it is transferred to the thrust command in airplane mode. Therefore the speed and altitude hold mode are coupled to each other and are engaged at the same time when an internal pilot engages any of the altitude or speed hold modes. The nonlinear simulation results of the guidance control for the preprogrammed mode and point navigation are also presented including automatic take-off and landing in order to prove the full control law.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.257-261
• /
• 2005

The helicopter system is non-linear and complex. Futhermore, because of absence of accurate mathematical model, it is difficult accurately to control its attitude. therefore, we propose a WAVENET control technique to control efficiently its elevation angle and azimuth one. Wavelet neural network(WAVENET) can construct systematically initial neural network as applying wavelet theory to feedforward network. It is proved through computer simulation that WAVENET has more excellent approximation capability than existing neural network. The simulation results using MATLAB are introduced.

• Spatial Information Research
• /
• v.15 no.4
• /
• pp.363-370
• /
• 2007

This study has been carried for the development of the basic algorithm of helicopter navigation system based on TRN (Terrain Referenced Navigation) with information input from the GPS. The helicopter determines flight path due to Origination-Destination analysis on the Cartesian coordinate system of 3-D DTM. This system shows 3-D mesh map and the O-D flight path profile for the pilot's acknowledgement of the terrain, at first. The system builds TCF (terrain clearance floor) far the buffer zone upon the surface of ground relief to avid the ground collision. If the helicopter enters to the buffer zone during navigation, the real-time warning message which commands to raise the body pops up using Matlab menu. While departing or landing, control of the height of the body is possible. At present, the information (x, y, z coordinates) from the GPS is assumed to be input into the system every 92.8 m of horizontal distance while navigating along flight path. DTM of 3" interval has been adopted from that which was provided by ChumSungDae Co., Ltd..

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.1-7
• /
• 2006

This paper presents a new point navigation guidance law which is useful for unmanned helicopters. Predicting the future position, the guidance law generates velocity and heading commands, which are used as input to autopilot. This method differs from conventional guidance law in that it reorients the direction of flight velocity vector directly, not by bank angle indirectly. For flight tests, we have developed a flight control system for a R/C helicopters. The system consists of a flight control computer, navigation sensors, and a ground station The results of the test show that the proposed law guides a unmanned helicopter along a line path within a given area. In the future, we are planning to extend the guidance law to the mission of path following. i.e., waypoint navigation.

• Proceedings of the KIEE Conference
• /
• 1997.07b
• /
• pp.597-599
• /
• 1997

무인 헬리콥터의 자세 정보를 계측할 수 있는 액체형 균형센서의 특성에 대해 연구하였다. 액체형 균형센서는 시간경과에 따른 누적오차가 없으므로 헬리콥터에 장착하면 장시간동안 균형을 유지시킬 수 있다. 제작된 균형센서의 각 전극에서 측정된 전압으로부터 기울어진 각도를 추정하기 위해 균형센서를 전기적으로 해석하고 측정된 전압과 각도사이의 환산모델을 유도하였다. 구해진 환산모델의 정확성을 실험을 통하여 입증하였다.