• 한국해양공학회지
• /
• 제37권5호
• /
• pp.215-224
• /
• 2023

While melting glaciers due to global warming have facilitated the development of polar routes, Arctic vessels require reliable anti-icing methods to prevent hull icing. Currently, the existing anti-icing method, i.e., the heating coil method, has disadvantages, such as disconnection and power inefficiency. Therefore, a carbon nanotube-based surface heating element method was developed to address these limitations. In this study, the numerical analysis of the surface heating element method was performed using ANSYS. The numerical analysis included conjugate heat transfer and computational fluid dynamics to consider the conduction solids and the effects of wind speed and temperature in cold environments. The numerical analysis method of the surface heating element method was validated by comparing the experimental results of the heating coil method with the numerical analysis results (under the -30 ℃ conditions). The surface heating element method demonstrated significantly higher efficiency, ranging from 56.65-80.17%, depending on the conditions compared to the heating coil method. Moreover, even under extreme environmental conditions (-45 ℃), the surface heating element method satisfied anti-icing requirements. The surface heating element method is more efficient and economical than the heating coil method. However, proper heat flux calculation for environmental conditions is required to prevent excessive design.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.122-132
• /
• 2009

Adsorption of toluene by activated carbon fiber (ACF) coated with dielectric heating element and desorption by applying microwave were investigated. In order to prepare adsorbent so that VOC can be desorbed by microwave heating, fine dielectric heating element with nano size was coated on the surface of the ACF using hybrid binder. Eight adsorbents (ACF-DHE, Activated Carbon Fiber coated with Dielectric Heating Element) were prepared with different amount of dielectric heating element, kinds of hybrid binder, and solvent. In order to investigate adsorption characteristics, BET surface area, pore volume, and average pore size were measured for each adsorbent including ACF. Breakthrough experiments with toluene concentration, flow rate, bed length using fixed bed reactor were performed to investigate adsorbality of adsorbent, and results were compared with that of the ACF. Desorption reactor was constructed with modified microwave oven to investigate heating effect on ACF-DHE by applying microwave power. Each adsorbent saturated with toluene were put into desorption reactor. Composition of desorbed gas generated by applying controlled microwave power to reactor was measured. Up to now, hot air desorption method has been used. Experimental results showed that desorption method with new adsorbent prepared by coating dielectric heating element on ACF can be used for industrial application.

• 한국산학기술학회논문지
• /
• 제19권2호
• /
• pp.683-688
• /
• 2018

본 논문에서는 탄소섬유를 이용한 면상발열체의 발열 상태를 영상처리 기술을 이용한 분석을 제안하였다. 면상발열체의 제작 방법은 탄소섬유를 작게 잘라 촙 상태로 만든 다음 분산제를 통하여 다시 결합시켜 준다. 그 다음 부직포 위에 분산제를 통해 결합된 탄소섬유 용액을 필터링 한다. 마지막 단계는 필터링된 탄소섬유를 건조 하면 부직포 형태의 면상 탄소 섬유를 얻을 수 있다. 면상발열체는 이렇게 제작된 면상 탄소 섬유에 전기를 인가하면 된다. 본 논문에서는 면상발열체를 4가지 방법으로 분석하였다. 분석 방법 중 면상 발열체의 발열특성 분석과 면상발열체의 발열속도 분석은 제작된 면상발열체가 정상군에 해당하는지를 확인한다. 절연 코팅 및 면상 발열체 모듈 분석은 실제 제품의 제작에 사용될 수 있는 면상발열체에 대해 영상처리 기술을 이용하여 2차원 이미지 분석이다. 면상발열체의 열화상 이미지 분석은 2차원 및 3차원으로 발열 상태를 분석할 뿐만 아니라, 발열의 상위온도 15~20%와 하위온도 15~20%를 이미지에 표시하는 프로그램 기법이다. 마지막 분석은 제작된 면상발열체의 상태를 화면에 직접 보여줌으로써 제작 과정 중 잘못된 부분을 쉽게 찾을 수 있다. 이와 같은 면상발열체의 이미지 분석 방법은 기존의 방법과 결합하여 발열상태를 더욱 정밀하게 분석할 수 있었다.

• 한국응용과학기술학회지
• /
• 제32권3호
• /
• pp.405-411
• /
• 2015

Carbon composites for flexible fiber heating element were examined to improve the electrical conductivity in this study. Carbon composites using carbon black, denka black, super-c, super-p with/without CNF or dispersant such as BCS03 and Sikament-nn were prepared. Carbon composite slurry was coated on plane film and yarns(cotton, polyester) and the performances of prepared heating materials were investigated by checking electrical surface resistance, adhesion strength. The plane heating element using carbon black under natural drying condition($25^{\circ}C$) had better physical properties such as surface resistance(185.3 Ohm/sq) and adhesion strength(above 90%) than those of other carbon composite heating elements. From these results, polyester heating element coated by carbon black showed better electrical line resistance(33.2 kOhm/cm) than cotton heating element. Then, it was found that polyester heating element coated by carbon black with CNF(3 wt%) and BCS03(1 wt%) appeared best properties(0.604 kOhm/cm).

• 소성∙가공
• /
• 제16권2호
• /
• pp.113-119
• /
• 2007

Rapid mold heating has been recent issue to enable the injection molding of thin-walled parts or micro/nano structures. Induction heating is an efficient way to heat material by means of an electric current that is caused to flow through the material or its container by electromagnetic induction. It has various applications such as heat treatment, brazing, welding, melting, and mold heating. The present study covers a finite element analysis of the induction heating process which can rapidly raise mold temperature. To simulate the induction heating process, the electromagnetic field analysis and transient heat transfer analysis are required collectively. In this study, a coupled analysis connecting electromagnetic analysis with heat transfer simulation is carried out. The estimated temperature changes are compared with experimental measurements for various heating conditions.

• 설비공학논문집
• /
• 제16권5호
• /
• pp.430-437
• /
• 2004

This paper is intended as an investigation of study on the thermal and electrical characteristics of the carbon heating element. In this experimentation, the electric material used is the crystalline graphite a kind of natural graphite. The bentonite is used to solidify the heating element and the vacuum furnace is used for sintering it. It is noted that the natural drying time should be at least 58 hours. The plating of the electric pole with the electroless nickel showed the lowest contact resistance among others. The resistance shows linear variation with regard to length. For the insulation and resolution, the glaze coating is best with 80% of water content. The temperature rising characteristic of the heating element is better than sheath heater saving 43% of rising time. The correlation equation for temperature was obtained with the electric power.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1217-1223
• /
• 2006

Induction heating is a process that is accompanied with magnetic and thermal situation. This paper presents a simulation of a magneto-thermal coupled problem of an induction heating process for moving inductor coil. In the magnetic and thermal analyses, temperature-dependent magnetic and thermal material properties were considered. As the inductor coil moves in the process, solution domains corresponding to inductor changes into those of the air, and the solution domains of air change into those of the inductor. For these reasons, modeling of induction heating process is very difficult with general purpose commercial programs. In this paper, induction heating process for moving coil was simulated with the concept of traveling the position of the heating planes. Finite element program was developed and finite element results were compared with the experimental results.

• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.1-7
• /
• 2003

잉크젯 헤드의 발열체에 적용하기 위해 $poly-Si/SiO_2/Si$ 다층기판 위에 결정화된 안정한 코발트실리사이드$(CoSi_2)$ 박막을 형성하여 오메가 형태의 발열체를 제작하고 발열체의 구조적 형상과 온도저항계수 등 전기적 특성을 조사, 연구하였다 $(CoSi_2)$ 박막의 형성은 금속 Co 박막을 급속 열처리장치를 이용하여 $800^{\circ}C$에서 20초 동안 질소 분위기에서 열처리하여 실리사이드 박막을 형성하였다. 발열체의 온도 저항계수 값은 약 $0.0014/^{\circ}C$ 값을 얻을 수 있었다. 인가전압 10 V, 주파수 10KHz 및 펄스간격 $1{\mu}s$ 인가시 발열체의 순간전력은 최대 2W를 나타내었다. 반복된 전압인가에 따른 발열체의 피로특성을 조사한 결과 15 V 이하의 전압인가시 $10^8$ 펄스 cycle 까지 저항변화가 거의 없었으나 17 V 인가전압에서는 $10^6$ cycle에서 발열체의 저항이 급격히 증가하였다.

• 소성∙가공
• /
• 제19권3호
• /
• pp.152-159
• /
• 2010

Rapid mold heating has been recent issue to enable the injection molding of thin-walled parts or micro/nano structures. High-frequency induction is an efficient way to heat mold surface by electromagnetic induction in a non-contact manner, and has been recently applied to the injection molding due to its capability of rapid heating and cooling of mold surface. The present study covers a three-dimensional finite element analysis to investigate heating efficiency and structural safety of the induction heating process of an injection mold. To simulate the induction heating process, an integrated simulation method is proposed by effectively connecting an electromagnetic field analysis, a transient heat transfer analysis and a thermal stress analysis. The estimated temperature changes are compared with experimental measurements for various types of induction coil, from which heating efficiency according to the coil shape is discussed. The resulting thermal stress distributions of the mold plate for various types of induction coils are also evaluated and discussed in terms of the structural safety.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.1-10
• /
• 2020

This study deals with the fabrication and thermal characterization of planar heating elements attached to the backside of the reflector used in the electrodeless lamp of a freezer. We tried to solve the problem of the local heat generation of the linear heating element that occurs about 50℃. The homogeneous dispersion and manufacturing excellence of the planar heating element produced were confirmed through SEM and EDS. In addition, the test specimens was prepared according to the change in the ratio of carbon fiber to the basis weight of the planar heating element, and a sample having a basis weight of 50g/㎡ having a content ratio of carbon fiber of 70% was selected. That sample showed low surface resistance of 4.3Ω/sq and high temperature of about 81℃ at 6V. Durability was confirmed by performing repeated bending evaluation of 3000 cycles for the sample. Large area test specimens were prepared to be applied to the actual reflector, insulated by EVA film and analyzed for their thermal characteristics. From 13V application, the temperature of the linear heating element was higher than 50℃ and the average temperature of 68℃ was maximum at 18V.