• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.197-197
• /
• 2017

In order to reduce the loss of perilla seeds at harvesting stage, different seeding methods and harvesting time had been applied to upland soil in NICS (National Institute of Crop Science), RDA, Milyang, Korea. The seeding methods were divided into hill and drill seeding, and harvesting time were 40%, 60%, 80%, and 100% color-changing of top cluster perilla (cv Deulsaem) seeds. Higher plant height and lowest flower cluster, thinner culm thickness was observed in drill seeding treated plot than hill seeding treated plot. However, field lodging occurred lower at drill seeding treatment (lodging degree 3) than hill seeding plot (lodging degree 5). Harvesting time affected the loss of perilla seeds and the loss rate of perilla seeds were investigated at different color-changing of top flower cluster. When seeds were harvested at 40%, 60%, 80%, and 100% color-changing of top cluster perilla seeds, the loss rate of hill and drill seeding showed no significant differences however the loss rated of 40, 60, 80, and 100 % color-changing of top flower cluster were 1.9% to 3.0%, 3.8% to 3.9%, 8.0% to 10.2%, and 16.1% to 22.7%, respectively. The harvesting time had no significant effects on the yield of perilla seeds. These results suggest that optimum harvesting time of perilla could be recommend at the 60% color-changing of top cluster to reduce the loss of perilla seeds.

• International Journal of Highway Engineering
• /
• v.16 no.6
• /
• pp.51-57
• /
• 2014

PURPOSES : An conventional method for electric power generation is converting thermal energy into mechanical energy then to electrical energy. Due to environmental issues such as global warming related with $CO_2$ emission etc., were the limiting factor for the energy resources which resulting in extensive research and novel technologies are required to generate electric power. Thermal energy harvesting using thermoelectric generator is one of energy harvesting technologies due to diverse advantages for new green technology. This paper presents a possibility of application of the thermoelectric generator's application in the direct exchange of waste solar energy into electrical power in road space. METHODS : To measure generated electric power of the thermoelectric generator, data logger was adopted as function of experimental factors such as using cooling sink, connection methods etc. Also, the thermoelectric generator、s behavior at low ambient temperature was investigated as measurement of output voltage vs. elapsed times. RESULTS : A few temperature difference between top an bottom of the thermoelectric generator is generated electric voltage. Components of an electrical circuit can be connected in various ways. The two simplest of these are called series and parallel and occur so open. Series shows slightly better performance in this study. An installation of cooling sink in the thermoelectric generator system was enhanced the output of power voltage. CONCLUSIONS : In this paper, a basic concepts of thermoelectric power generation is presented and applications of the thermoelectric generator to waste solar energy in road is estimated for green energy harvesting technology. The possibility of usage of thermoelectric technology for road facilities was found under the ambient thermal gradient between two surfaces of the thermoelectric module. An experiment results provide a testimony of the feasibility of the proposed environmental energy harvesting technology on the road facilities.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.311-319
• /
• 2018

Purpose: The aim of this study is to develop a small combine for harvesting miscellaneous cereal crops. Methods: A prototype small combine was designed and constructed. Its specifications and basic performance were investigated. Results: The prototype small combine for harvesting miscellaneous cereal crops was designed and constructed to reflect similar specifications as those of the conventional combine. The prototype small combine comprises a diesel engine with the rated power/speed of 22.0 kW/2,600 rpm, three-stage primary and two-stage speed range transmission shifts, and a double acting threshing part. The maximum travel speeds of the prototype combine are approximately 0.72 m/s, 2.50 m/s, 0.30 m/s at the low, high speed range shifts in the forward direction, and while traversing in the reverse direction, respectively. The minimum radius of turning was approximately 1.50 m. In a static lateral overturning test, the prototype combine overturned neither to the right nor to left on a $30^{\circ}$ slope. The results of an oilseed rape harvesting test included the maximum operating speed of 0.32 m/s, the grain loss ratio of approximately 9.0%, and the effective field capacity of approximately 10.3 a/h. Additionally, among the outputs in grain outlet, the whole grains, damage grains, and materials other than grain (MOG) ratios accounted for 97.4%, 0.0%, and 2.6%, respectively. Conclusions: The prototype small combine for harvesting miscellaneous cereal crops indicates good driving ability and stability. The results of the oilseed rape harvesting test reveal that the harvesting performance must be enhanced such that the separating and cleaning parts are more suitable for each type of crop, thus reducing grain loss and foreign substances among the outputs in grain outlet. An improved small prototype combine could be used effectively to mechanize the harvesting of miscellaneous cereal crops in small family farms or semi-mountainous areas.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.407-417
• /
• 2015

Recently, piezo-aeroelastic energy harvesting has received greater attention. In the present study, a piezo-aeroelastic energy harvester using a nonlinear trailing-edge flap is proposed, and its nonlinear aeroelastic behaviors are investigated. The energy harvester is modeled using a piezo-aeroelastic model of a two-dimensional typical section airfoil with a trailing-edge flap (TEF). A piezo-aeroelastic analysis is carried out using RL and time-integration methods, and the results are verified with the experimental data. The linearizing method using a describing function is used for the frequency domain analysis of the nonlinear piezo-aeroelastic system. From the linear and nonlinear piezo-aeroelastic analysis, the limit cycle oscillation (LCO) characteristics of the proposed energy harvester with the nonlinear TEF are investigated in both the frequency and time domains. Finally, the authors discuss the air speed range for effective piezo-aeroelastic energy harvesting.

• Advances in Computational Design
• /
• v.1 no.2
• /
• pp.155-173
• /
• 2016

This paper presents a method of design for the energy harvesting of a piezoelectric cantilever beam. Vibration modes have strain nodes where the strain distribution changes in the direction of the beam length. Covering the strain nodes of the vibration modes with continuous electrodes effects a cancellation of the voltages outputs. The use of segmented electrodes avoids cancellations of the voltage for multi-mode vibration. The resistive load affects the voltage and generated power. The optimum resistive load is considered for segmented and continuous electrodes, and then the power output is verified. One of the effective parameters on energy harvesting performance is the existence of concentrated mass. This topic is studied in this paper. Resonance and off-resonance cases are considered for the harvester. In this paper, both theoretical and experimental methods are used for satisfactory results.

• Korean Journal of Plant Resources
• /
• v.20 no.2
• /
• pp.125-128
• /
• 2007

Plan stability production investigating 1st harvesting degree for maximum leaf quantity enlargement, is as following it summarize result that test for 3 years since 2002 allowing 4 processing such as trunk lower column department harvesting, Foliar and rhizoma growth were tendency that give protective care 1 st harvesting height is short, but there were many the number of tillering crawl, Distribution of rhizome about diameter 5mm low 58%, large rhizome's ratio was high tendency harvesting height is short. Because foliar amount is much harvesting height is short in ground department, 15% rose in soil surface harvesting since 292kg provision per 5cm harvesting 10a, The time of refining the harvest of stems and leaves before drying has reduced when the height of the harvest is low, and the 5cm harvest has decreased 30% compared to the soil surface harvest.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.320-330
• /
• 2018

Purpose: The aim of this study was to investigate the harvesting performance of a prototype small combine for buckwheat and adlay. Methods: The prototype small combine was designed and constructed. Its ratio of grain loss, ratio of output components in the grain outlet, and field capacity for harvesting buckwheat and adlay were analyzed through field tests. Results: The prototype small combine required a working width of about 0.6 to 0.7 m to harvest buckwheat. The maximum travel speed was about 0.36 m/. The total ratio of grain loss was about 21.6%, which consisted of 8.8% at the header and 12.8% at the dust outlet. The grain and the material other than grain (MOG) ratios at the grain outlet were 94.1% and 5.9% respectively. In the case of adlay harvest, the maximum working width was about 1.2 m, that is, two rows. The range of maximum travel speed was about 0.45 to 0.46 m/s. When adlay was harvested in one row, the total ratio of grain loss ranged from 36.3 to 42.8% according to the cutting height. The cutting height of 30 cm resulted in a higher total ratio of grain loss than 60 cm and 90 cm. When the cutting height was 60 cm, there was no significant change in the total ratio of grain loss according to the number of working rows and the stage of the primary transmission shift. The total ratio of grain loss ranged from 35.2 to 37.7%. The grain and the MOG ratios at the grain outlet ranged from 93.1 to 95.8% and from 4.2 to 6.9%, respectively. No significant difference was observed in relation to cutting height, number of working rows, and the stage of the primary transmission shift. Conclusions: The prototype small combine for harvesting miscellaneous cereal crops showed good potential for the efficient harvesting of buckwheat and adlay. However, to improve the harvesting performance, there seems to be a need to develop new crop varieties suitable for machine-based harvesting and improve the transmissions, reels, separation/cleaning systems.

• International Journal of Highway Engineering
• /
• v.16 no.4
• /
• pp.51-62
• /
• 2014

PURPOSES: This research is a basic study for application method in korea of energy harvesting technology, and it is a research to find out the direction of architectural planning through analyzing cases of interseasonal heat transfer system applied buildings. METHODS : In this paper authors investigate application necessity of energy harvesting technology, we analyzed energy use status of building section through analyzing domestic energy consumption status and analyzed domestic renewable energy generation potential. Also we study the features of energy harvesting technology, interseasonal heat transfer system, and case study on interseasonal heat transfer system applied buildings. RESULTS : On the basis of case study on interseasonal heat transfer system applied buildings, we analyzed feasibility study and classified into four sections(economic, environment, design, applicability), and suggested directions of architectural planning. CONCLUSIONS: Economic renewable energy for public and commercial buildings(hospitals, offices, schools, factories) can be provided effectively using Interseasonal Heat Transfer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.219-219
• /
• 2008

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for ubiquitous sensor networks (USN). There are several power generating methods such as thermal gradients, solar cell, energy produced by human action, mechanical vibration energy, and so on. Most of all, mechanical vibration is easily accessible and has no limitation of weather and environment of outdoor or indoor. In particular, the piezoelectric energy harvesting from ambient vibration sources has attracted attention because it has a relative high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system hassome drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure. In this case, the energy harvester has a lower natural frequency under 200 Hz than a normal cantilever structure. Moreover, it has higher an energy conversion efficient because shear mode ($d_{15}$) is much larger than 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate as a standalone power generator for USN.

• Journal of Biosystems Engineering
• /
• v.40 no.1
• /
• pp.10-18
• /
• 2015

Purpose: The study was conducted to investigate the proper working conditions like the mesh size of the concave and the chaffer angle of the oscillating sieve, and the fan speed of the head-feeding rice combine for foxtail millet harvesting. Methods: The study aimed to determine the harvesting conditions for the rice combine harvester at a 0.5 m/s working speed and at $40^{\circ}$ and $55^{\circ}$ sieve chaffer angles. The harvesting loss of the foxtail millet based on the speed of the fan and the oscillating speed of the sieve was measured at three levels of fan speed and oscillating sieve speed. Results: The threshing rates of different foxtail millet varieties were 64.1~83.5% at a mesh size of 7 mm of the concave. In experimental foxtail millet harvesting, the optimal operating condition of the rice combine harvester included a $40^{\circ}$ sieve chaffer angle and a 4.8 Hz oscillating sieve (cleaning shoe) frequency. The grain loss was found to be lower at a $40^{\circ}$ than at a $55^{\circ}$ sieve chaffer angle. In field harvesting using the combine harvester, the lowest harvesting grain loss rate of the foxtail millet varieties ranged between 0.2~0.5% at a 7 mm mesh concave, $40^{\circ}$ chaffer angle, 4.8 Hz sieve frequency, and a 20 m/s fan speed at an engine speed of 2,000 revolutions per minute (RPM). Conclusions: Findings showed that foxtail millet could be harvested using the combine harvester.