• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.1-20
• /
• 1997

The automotive industry as the major industry of the nation has affected both society and economy since the automobile was invented, and the main technique that help to performance improvement of the automobile has been developed. But, the painting technique lags behind the main technique of the automobile because that was neglected. Specially, we can say that in case of the painting technique of the automobile of our nation is so weak situation. After we changed the injecting pressure, the composition ratio (paint, hardener, thinner) and the injecting flow rate from spray-gun by PDPA, we studied the character of the injecting velocity and droplet size, and found the fittest condition. So, we got the following result to help mending paint technique of automobile surface. We could know the following fact from the experiment result. When it does mending paint of automobile, there is most suitable that to inject the paint as injecting pressure 200∼300 kPa and to inject the ratio of paint 10 : 1 : 1 when the fluid adjective knob valve spay-gun is open full.

• 반도체디스플레이기술학회지
• /
• 제12권1호
• /
• pp.23-28
• /
• 2013

Epoxy resins are widely used in microelectronics packaging such as printed circuit board and encapsulating for semiconductor manufacturing. Water can diffuse into and through the epoxy matrix systems and moisture absorption at boarding interfaces of matrix resin systems can lead to a hydrolysis at the interfaces resulting in delamination of encapsulating materials. In the study, the changes of diffusion coefficient and moisture content ratio of epoxy resin systems with nano-sized fillers according to the change of liquid type epoxy resins were investigated. RE-304S, RE-310S, RE-810NM and HP-4032D as a epoxy resin, Kayahard AA as a hardener, and 1B2MI as a catalyst were used in these epoxy resin systems. After curing, moisture content ratios were measured with time under the 85 and 85% relative humidity condition using a thermo-hydrostat. The maximum moisture absorption ratio and diffusion coefficient of EMC decrease with the filler content. It can be seen that these decreases are due to the increase of filler surface area and the decrease of moisture through channel with the content of nano-sized filler.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.63-70
• /
• 2000

In 1925, H.J. Joosten was the first in the world to use chemical injection grouts composed of sodium silicate and calcium chloride. This unique development prompted the introduction of other chemical grouting techniques. Among these chemical grouting techniques, sodium silicate based grout has been the most widely used in the world, but it has not been generally considered to be a permanent material. Therefore, studies to improve the weak points of sodium silicate based grout have been conducted, and new applications of grout were recently developed. We also developed the micro fine hybrid silicate grout of suspention type which properties are sepecialized as the high strength and durability, according to the reactant of special sodium silicate grout and the high strength hardener. As the results of this study we could derive the 2 times over high strength of Micro fine hybrid Silicate grouting method(MS method) more than that of the ordinary sodium silicate grout. And also we could confirm that the alkali leakage of micro fine hybrid silicate grout is less than that of ordinary sodium silicate grout. So we could get the high strength and durability of hybrid silicate grout are superior to those of ordinary sodium silicate grout.

• 한국초전도ㆍ저온공학회논문지
• /
• 제7권1호
• /
• pp.42-46
• /
• 2005

The resistive type high temperature superconducting fault current limiter (HTSFCL) limits the fault current using the resistance generated by fault current. The generated resistance by fault current makes large pulse power which makes the operation of HTSFCL unstable. So, the cryogenic cooling system of the resistive type HTSFCL must diffuse and eliminate the pulse energy very quickly. Although the best way is to make wide direct contact area between HTS winding and coolant as much as possible, HTS winding also needs the impregnation layer which fixes and protects it from electromagnetic force. This paper deals with the thermal conductivity and dielectric strength of some epoxy compounds for the impregnation of high temperature superconducting (HTS) winding in liquid nitrogen. The measured data can be used in the optimal design of impregnation for HTS winding. Aluminar filling increased the thermal conductivity of epoxy compounds. Hardener also affected the thermal and electric characteristic of epoxy compounds.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.99-99
• /
• 2010

Polymer nanocomposite has been attracting much attention as a new insulation material, since homogeneous dispersion of nm-sized inorganic fillers can improve various properties significantly. In this paper, various kinds of epoxy based nanocomposites were made and AC breakdown strength of Nano-TiO2 and micro-silica filler mixture of epoxy based composites were studied by sphere to sphere electrode. Moreover, nano- and micro-filler combinations were adopted as an approach toward practical application of nanocomposite insulation materials. Nano-TiO2 particle size is about 10nm and composites ratio was resin (100) : hardener (82) : accelerator (1.5). AC breakdown test was performed at room temperature (25 [$^{\circ}C$], 80 [$^{\circ}C$] and 100 [$^{\circ}C$] in the vicinity of Tg (90[$^{\circ}C$]). And thermal conductivity were measured by ASTM-D5470.

• Design & Manufacturing
• /
• 제13권4호
• /
• pp.1-9
• /
• 2019

In-mold Coating is a method that can simultaneously perform injection molding and surface coating in injection mold. The material used for coating is two-component polyurethane which is composed of polyol and isocyanate. L-type mixing head can be used to mix polyol and isocyanate uniformly, and inject them inside the mold cavity. The surface quality of the injection molded products by using in-mold coating depends on the mixing uniformity between main agent and hardener. In this study, flow analysis was performed to design a mixing head for uniform mixing of two-component polyurethane. Especially the effects of design parameters of mixing head on mixing uniformity and nozzle pressure were investigated. The parameters of mixing head were mixing chamber diameter, cleaning cylinder diameter, nozzle alignment angle in the horizontal and vertical direction, and cleaning piston position. It was found that optimal design values were mixing chamber diameter of 3.5 mm, cleaning cylinder diameter of 5.0 mm, nozzle horizontal/vertical alignment angles of 140°/160°, and cleaning piston position of 1.8 mm. The optimal values would be used to develop a two-component mixing head achieving an uniform mixing for in-mold coating.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.133-136
• /
• 2005

The accidents attributed to the forklift have increased as the number of the forklift increases. It is significant that most of the accidents were fatal. This study investigated slip distance of forklift depending upon the floor materials and their conditions in industrial site. For doing this, an experiment was conducted, in which the floor materials and their conditions were adopted as independent variables and the slip distance as dependent variable. Six floor materials included asphalt concrete, two color hardener mortar, epoxy paint and deluxe tile. Two types of floor conditions, wet and dry, were used in the experiment. The results showed that the slip distance was shorter on the asphalt and concrete floors than on other floors, and that the distance on the wet floor was six times longer than that on the dry condition. Based on this result, it is recommended that as in the advanced countries, the regulation or standard on the floor conditions such as friction coefficient be established for reducing forklift relevant accidents.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 추계 학술논문 발표대회
• /
• pp.153-154
• /
• 2018

As the air pollution progresses, the pollution degree of the indoor air quality is increased, and when the pollution degree of the indoor air quality is increased, it causes respiratory diseases and skin diseases. In addition, volatile organic compounds are released from the materials used for architectural interior decoration, and volatile organic compounds are the main cause of polluting indoor air quality. In order to improve indoor air quality, we tried to secure indoor air quality pollution by using photocatalyst which has the function of decomposing harmful substances. photocatalyst is a material that promotes chemical reaction by absorbing light. The photocatalyst used in the experiment was TiO₂, In this study, an adsorption type hardener for reducing volatile organic compounds was prepared by photocatalytic reaction. the formaldehyde and CO₂ concentrations of the cured products were analyzed according to the TiO₂ content.

• Transactions on Electrical and Electronic Materials
• /
• 제12권4호
• /
• pp.160-163
• /
• 2011

Polymer nanocomposite has been attracting more attention as a new insulation material because homogeneous dispersion of nano-sized inorganic fillers can improve various properties significantly. In this paper, various kinds of epoxy-based nanocomposites were made, and the AC breakdown strengths of Nano filler and micro-$SiO_2$ filler mixtures of epoxy-based composites were analyzed using sphere-to-sphere electrodes. Moreover, nano- and microfiller combinations were investigated as an approach to practical application of nanocomposite insulation materials. Its composition ratio was 100 (resin):82 (hardener):1.5 (accelerator). AC breakdown tests were performed at room temperature ($25^{\circ}C$), $80^{\circ}C$, and $100^{\circ}C$ in the vicinity of $T_g$ ($90^{\circ}C$). Thermal conductivity was measured using TC-30.

• 한국자기학회지
• /
• 제24권3호
• /
• pp.86-89
• /
• 2014

이방성 희토류 본드자석은 자성분말과 유기 바인더로 구성되며 본드자석 내에서 유기 바인더는 분말의 배향을 유리하게 하는 역할을 한다. 유기 바인더는 고분자 수지, 활제, 경화제, 커플링제 등으로 구성되며 자성분말에 적합한 유기 바인더를 제조하기 위해 본 연구에서는 다양한 성분을 선정하여 유기 바인더를 제조하였고 구성비 및 첨가량을 조절하여 이를 본드자석에 적용하였다. 특성평가를 통해 자기특성 및 기계적 특성을 측정하였고 이로부터 본드자석에 적합한 유기 바인더의 성분 및 비율을 확인하였다.