• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.344-350
• /
• 2004

This is the study on dry sliding wear behavior of unidirectional carbon fiber reinforced epoxy matrix composite at ambient temperature. The wear rates and friction coefficients against the stainless steel counterpart specularly processed were experimentally determined and the resulting wear mechanisms were microscopically observed. Three principal sliding directions relative to the dominant fiber orientation in the composite wear selected. When sliding took place against smooth and hard counterpart, the highest were resistance and the lowest friction coefficient were observed in the antiparallel direction. When the velocity between the composite and the counterpart went up, the wear rate increased. The fiber destruction and cracking caused fiber bending on the contact surface, which was discovered to be dominant wear mechanism.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.960-965
• /
• 1995

Hard Ti(C, N) layers of various compositions were coated on ASP30 tool steel employing a reactive HCD ion plating technique. The effect of film composition on the wear characteristics were investigated in lights of hardness, adhesion and wear mechanism. With an increase in the amount of nonmetallic component(N, C), the hardness of films increased, but the increase in carbon content resulted in poor adhesion. Within the concentration range of ([C+N]/Ti<1), these trends became mute clear than in the concentration below stoichiometry. Therefore, the wear resistance could be maximized when the film is deposited with the concentration of ([C+N]/Ti<1) for high microhardness and, at the same time, with the low carbon contents not to wear out in adhesive mode.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.335-344
• /
• 1998

In this study, the tearing energy and the rate of crack propagation of natural rubber (NR) compounds were evaluated to improve the crack resistance of tank-track pads. Although the factors affecting the crack resistance properties of NR compounds are various in this experiment, the effects of filler(carbon black) and the crosslinking system were evaluated. When the amount of accelerator is equal to that of sulfur( eg. efficient vulcanization), the compound shows the most excellent in the aged mechanical properties and the crack resistance properties. The ISAF carbon black(CB) having a good reinforcing characteristics was better than any other CB grades in physical properties and processablity. The optimum content was 50phr.

• Carbon letters
• /
• v.13 no.1
• /
• pp.1-16
• /
• 2012

The near explosion of attention given to graphene has attracted many to its research field. As new studies and findings about graphene synthesis, properties, electronic quality control, and possible applications simultaneous burgeon in the scientific community, it is quite hard to grasp the breadth of graphene history. At this stage, graphene's many fascinating qualities have been amply reported and its potential for various electronic applications are increasing, pulling in ever more newcomers to the field of graphene. Thus it has become important as a community to have an equal understanding of how this material was discovered, why it is stirring up the scientific community and what sort of progress has been made and for what purposes. Since the first discovery, the hype has expediently led to near accomplishment of industrial-sized production of graphene. This review covers the progress and development of synthesis and transfer techniques with an emphasis on the most recent technique of chemical vapor deposition, and explores the potential applications of graphene that are made possible with the improved synthesis and transfer.

• Journal of the Korean Institute of Educational Facilities
• /
• v.25 no.2
• /
• pp.3-9
• /
• 2018

This study is designed to measure the indoor environment and research on the environmental situation in the lecture room where the lecture is conducted during the winter time in order to understand the level of environment in the lecture room and then suggest the method of improving the environment in the lecture room in the future. The findings are as follows. First, the number of ventilation measured at Lecture Room 1 was 1.2 times/hour while that at Lecture Room 2 was 2.2 times/hour. Second, the lighting at Lecture Room 1 and 2 was 650~700 lux while the noise at Lecture Room 1 and 2 was not more than 60dB. Third, Group 1 and Group 2 felt in the same way that the air quality in the lecture room was not good when the air quality was measured in 30 minutes after the start of lecture. Fourth, both Group 1 and Group 2 showed the lowered concentration on the class in 30 minutes after the start of the class when the room was heated. But Group 1 got less drop in the concentration when they was put in the non-heated room. Fifth, As for the change in the carbon dioxide volume during lecture, the carbon dioxide volume in the room where the windows was closed rose 1,000~1,400ppm from that at the time of start, thus showing that the indoor air quality got worsened. In addition, it is hard to control the indoor temperature due to the heating and non-heating. Accordingly, it is necessary to get the heating system which can make the ventilation in order to keep the environmental level in the lecture room to a certain level and keep the proper indoor temperature.

• Journal of Powder Materials
• /
• v.12 no.5 s.52
• /
• pp.336-344
• /
• 2005

In the present study, the focus is on the effect of cobalt oxide powder in the carbothermal reduction of the titanium-cobalt-oxygen based oxide powder by solid carbon for the optimizing synthesis process of ultra fine TiC/Co composite powder. The titanium-cobalt-oxygen based oxide powder was prepared by the combination of the spray drying and desalting processes using the titanium dioxide powder and cobalt nitrate as the raw materials. The titanium-cobalt-oxygen based oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under flowing argon atmosphere. Changes in the phase structure and thermal gravity of the mixture during carbothermal reduction were analysed using XRD and TGA. Titanium-cobalt-oxygen based oxide powder desalted at $600^{\circ}C$ had a mixture of $TiO_2\;and\;Co_{3}O_4$. And the one desalted at $800^{\circ}C$ had a mixture of $TiO_2\;and\;CoTiO_3$. In the case of the former powder, the reduction of cobalt oxide powder in the titanium-cobalt-oxygen based oxide powder occurred at lower temperature than the latter one. However, the carbothermal reduction of titanium dioxide powder in the titanium-cobalt-oxygen based oxide powder with a mixture of $TiO_2\;and\;Co_{3}O_4$ occurred at higher temperature than the one with a mixture of $TiO_2\;and\;CoTiO_3$. And also, the former powder showed a lower TiC formation ability than the latter one.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.315-315
• /
• 2007

본 논문에서는 DLC (Diamond-like carbon)박막이 가지는 높은 경도, 낮은 마찰계수, 전기적 절연성, 화학적 안정성 등의 특성을 이용하여, 리소그래피를 위한 resist나 hard coating물질로써 응용하기 위해, DLC 박막의 에칭에 관한 연구를 진행하였다. DLC 박막의 합성 과 에칭은 13.56 MHz RF plasma enhanced vapor deposition technique를 통해 이루어졌으며, DLC 박막은 150 W의 RF Power에서 메탄 $(CH_4)$과 수소$(H_2)$ 가스를 이용하여 약 300 nm의 두께로 제작되었으며, DLC박막의 에칭은 RF power의 변화 (50~250 W)와 산소 $(O_2)$가스의 유량변화 (5~25 sccm)에 따라 실시하였다. 에칭 되어진 DLC 박막의 표면 특성들은 AFM (atomic force microscopy)과 contact angle 장치를 사용하여 측정되었고, 측정된 결과로써 DLC 박막은 RF power와 산소 가스의 유량이 높을수록 etching rate는 증가하였고, 박막의 표면은 거칠어졌으며, 결국 DLC 표면에서는 산소에 의한 결합의 증가로 인해 친수성을 나타내었다.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.271-279
• /
• 2020

Non-ferrous metals, widely used in the mechanical industry, are difficult to machine, particularly by drilling and tapping. Since non-ferrous metals have a strong tendency to adhere to the cutting tool, the tool life is greatly deteriorated. Diamond-like carbon (DLC) is one of the promising candidates to improve the performance and life of cutting tool due to their low frictional property. In this study, a sacrificial DLC layer is applied on the hard nitride coated drill tool to improve the durability. The DLC coatings are fabricated by controlling the acceleration voltage of the linear ion source in the range of 0.6~1.8 kV. As a result, the optimized hardness(20 GPa) and wear resistance(1.4 x 10-8 ㎣/N·m) were obtained at the 1.4 kV. Then, the optimized DLC coating is applied as an sacrificial layer on the hard nitride coating to evaluate the performance and life of cutting tool. The Vickers hardness of the composite coatings were similar to those of the nitride coatings (AlCrN, AlTiSiN), but the friction coefficients were significantly reduced to 0.13 compared to 0.63 of nitride coatings. The drilling test were performed on S55C plate using a drilling machine at rotation speed of 2,500 rpm and penetration rate of 0.25 m/rev. The result showed that the wear width of the composite coated drills were 200 % lower than those of the AlCrN, AlTiSiN coated drills. In addition, the cutting forces of the composite coated drills were 13 and 15 % lower than that of AlCrN, AlTiSiN coated drills, respectively, as it reduced the aluminum clogging. Finally, the application of the DLC sacrificial layer prevents initial chipping through its low friction property and improves drilling quality with efficient chip removal.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.190.1-190.1
• /
• 2015

Graphite has excellent mechanical and physical properties. It is known to advanced materials and is used to materials for molds, thermal treatment of furnace, sinter of diamond and cemented carbide tool etc. SiC materials are coated on the surface and holes of graphite to protect particles emitted from porous graphite with 5%~20% porosity and make graphite hard surface. SiC materials have high durability and thermal stability. Thermal CVD method is widely used to manufacture SiC thin films but high cost of machine investment and production are required. SiC thin films manufactured by Si reaction liquid and vapore with carbon are effective because of low cost of machine and production. SiC thin films made by vapor silicon infiltration into porous graphite can be obtained for shorter time than liquid silicon. Si materials are evaporated to the graphite surface in about $10^{-2}$ torr and high temperature. Si materials are melted in $1410^{\circ}C$. Si vapor is infiltrated into the surface hole of porous graphite and $Si_xC_y$ compound is made. $Si_x$ component is proportional to the Si vapor concentration. Si diffusion coefficient is estimated from quadratic equation obtained by Fick's second law. The steady stae is assumed. Si concentration variation for the depth from graphite surface is fitted to quadratic equation. Diffusion coefficient of Si vapor is estimated at about $10^{-8}cm^2s^{-1}$.

• Journal of the Korean Society of Safety
• /
• v.17 no.1
• /
• pp.61-67
• /
• 2002

The toxic gases released from a fire can be classified as asphyxiants such as carbon monoxide, and irritants such as hydrochloric acid, etc. It is recognized that the combustion characteristic of interior upholstery is one of the important factors to determine the severity of indoor fires. In this study, several of the mostly used interior upholsteries including wallpaper, veneer board, curtain and floor cover, were selected to be evaluated by using the method of NES 713. The toxicity indices of the experimental samples, which indicate their toxic potentials in a fire were lowered in the order of Wallpaper (Flame Retardant) 8.5>Floor Cover(Hard) 4.8>polyurethane 4.3>Floor Cover(Soft) 3.5>PVC 2.8> Veneer Board 2.3> Floor Cover(flame retardant) 2.1>Wallpaper(Promulgation) 1.4>Curtain 0.9. It is concluded that, among all the tested upholsteries, wallpaper (flame retardant) would release the largest quantity of Toxic gases in a fire.