• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.269-269
• /
• 2012

A new ion source has been designed, fabricated, and installed at the NBTS (Neutral Beam Test Stand) at the KAERI (Korea Atomic Energy Research Institute) site. The goalis to provide a 100 keV, 2MW deuterium neutral beam injection as an auxiliary heating of KSTAR (Korea Super Tokamak Advanced Research). To cope with power demand, an ion current of 50 A is required considering the beam power loss and neutralization efficiency. The new ion source consists of a magnetic cusp bucket plasma generator and a set of tetrode accelerators with circular copper apertures. The plasma generator for the new ion source has the same design concept as the modified JAEA multi-cusp plasma generator for the KSTAR prototype ion source. The dimensions of the plasma generator are a cross section of $59{\times}25cm^2$ with a 32.5 cm depth. The anode has azimuthal arrays of Nd-Fe permanent magnets (3.4 kG at surface) in the bucket and an electron dump, which makes 9 cusp lines including the electron dump. The discharge properties were investigated preliminarily to enhance the efficiency of the beam extraction. The discharge of the new ion source was mainly controlled by a constant power mode of operation. The discharge of the plasma generator was initiated by the support of primary electrons emitted from the cathode, consisting of 12 tungsten filaments with a hair-pin type (diameter = 2.0 mm). The arc discharge of the new ion source was achieved easily up to an arc power of 80 kW (80 V/1000 A) with hydrogen gas. The 80 kW capacity seems sufficient for the arc power supply to attain the goal of arc efficiency (beam extracted current/discharge input power = 0.8 A/kW). The accelerator of the new ion source consists of four grids: plasma grid (G1), gradient grid (G2), suppressor grid (G3), and ground grid (G4). Each grid has 280 EA circular apertures. The performance tests of the new ion source accelerator were also finished including accelerator conditioning. A hydrogen ion beam was successfully extracted up to 100 keV /60 A. The optimum perveance is defined where the beam divergence is at a minimum was also investigated experimentally. The optimum hydrogen beam perveance is over $2.3{\mu}P$ at 60 keV, and the beam divergence angle is below $1.0^{\circ}$. Thus, the new ion source is expected to be capable of extracting more than a 5 MW deuterium ion beam power at 100 keV. This ion source can deliver ~2 MW of neutral beam power to KSTAR tokamak plasma for the 2012 campaign.

• Journal of Bio-Environment Control
• /
• v.12 no.3
• /
• pp.107-113
• /
• 2003

This study was carried out to improve the performance of pre-developed heat recovery devices attached to exhaust-gas flue connected to combustion chamber of greenhouse heating system. Four different units were compared in the aspect of heat recovery performance; A-, B-, and C-types are exactly the same with the old ones reported in previous studies. D-type newly developed in this experiment is mainly different with the old ones in its heat exchange area and tube thickness. But airflow direction(U-turn) and pipe arrangement are similar with previous three types. The results are summarized as follows; 1. System performances in the aspect of heat recovery efficiency were estimated as 42.2% for A-type, 40.6% for B-type, 54.4% for C-type, and 69.2% for D-type. 2. There was not significant improvement of heat recovering efficiency between two different airflow directions inside the heat exchange system. But considering current technical conditions, straight air flow pattern has more advantage than hair-pin How pattern (U-turn f1ow). 3. The main factors influencing on heat recovery efficiency were presumably verified to be the total area of heat exchange surface, the thickness of ail-flow pipes, and the convective heat transfer coefficient influenced by airflow velocity under the conditions of allowable pipe durability and safety. 4. Desirable blower capacity for each type of heat recovery units were significantly different to each other. Therefore, the optimum airflow capacity should be determined by considering in economic aspect of electricity required together with the optimum heat recovery performance of given heat recovery systems.

• Journal of Korean Society of Forest Science
• /
• v.76 no.4
• /
• pp.357-360
• /
• 1987

1. The hair cells on adaxial surface turned out to be penetration way of Gleosporium Thea sinensis in tea plant. 2. The most parts of Gleosporium Thea sinensis generated in tea plant were young leaves with first-fifth leaves from tip of shoot. 3. The proper temperature for spore germination on leaf is $25-27^{\circ}C$, soaked by water for 12 hours. 4. For prevention of Gleosporium Thea sinensis the drug-spay in tea plant would be the most effective when sprayed at this temperature range, and the control of Gleosporium Thea sinensis would be possible through selection of tea plant with few hairs. 5. The treatment of bordeaux mixture to prevent growth of conidiospore was 48.3% more effective than in control plot which were not sprayed. 6. The effect of sprayed bordeaux mixture decreased to about 28.5% after one week of spray.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.3
• /
• pp.226-237
• /
• 2005

Purpose : Extensive defect of oral and maxillofacial area is usually reconstructed with composite flap including skin paddle. However, if the defects are lined with only skin components, the mucosa's role in mastication and texture are not restored. Furthermore, stiffness and hair-growing prevent denture rehabilitation and good oral hygiene. This study was performed to overcome the disadvantages of composite soft tissue flaps including the skin and to make a model for myo-mucosal flaps. Materials and methods : Buccal mucosa sized $0.5\times1.0\;cm^2$ from New Zealand rabbit (around 1.5kg) was harvested and cultivated by the modification of Rheinwald and Green's keratinocyte culture method. Cultured mucosa was grafted on the fascia of latismus dorsi as form of mucosal sheet. After 7, 10, 14 days, the myomucosal flap was excised and evaluated under light microscope with H & E and immunohistochemical staining. As control group, harvested buccal mucosa from rabbit was transplanted to gracilis muscle(n=6). Results : From 7 days after prelamination, the basal layer of the grafted mucosa resembled that of normal mucosa. As control group, transplanted mucosa had original shape but there's slight inflammatory reaction. Prelaminated mucosa has 19.8$\pm$4.59 cell layers and some samples have more than 20 layers. The expression rate of PCNA was relatively strong (42.9%$\pm$14.1) at the basal layer of grafted mucosa and the laminin was found at the basal layer. On the contrary, prelaminated mucosa at 10 days showed moderate expression rate of PCNA(32.4%$\pm$4.62). We found the mucosal layer was somehow disappeared and there is strong inflammatory reaction. After 14 days prelamination, the grafted oral keratinocytes were almost disappeared and expression of PCNA was not observed. Conclusion : We can make 75 fold large mucosal($3850mm^2$) sheet from small samples of mucosa $(50mm^2)$. Epithelial sheet that grafted on the fascia of muscle underwent differentiation and proliferation. But after 10, 14 days, there was strong inflammatory reaction and the grafted mucosa was destroyed from surface layer. In rabbit model, transfer of fascio-mucosal flap should be done from 7 to 10 days after prelamination.

• Journal of Animal Environmental Science
• /
• v.1 no.1
• /
• pp.9-19
• /
• 1995

This study was carried out to investigate the effect of sawdust bedding barn on manure handing, management labour and physiological aspect of dairy cows, and then to establish the criteria on the optimum utilization method of sawdust bedding barn. 46 tie stall barns and 49 sawdust bedding barns were surveyed to cmopare the milk productivity between two different barns, and also 5 tie stall barns, 15 sawdust bedding barns and 1 rice hull bedding barn were selected to study the utilization situation of sawdust barn in Kyung-Ki province area. The major results obtained were as follows; 1. The roof material of sawdust barn were consisted of 66% vinyl house, 23% PVC light and 11% slate and galvanum coated tin. Most of the floor structure was earth ground with the rate of the approximately 82%. 2. The average occupied area of sawdust bed per cow was 15.2 $m^2$, depth that 30 cm and the utilization period was 12 months. 3. Milk Yield was significantly higher at sawdust barn than at tie stall barn(P<0.01). Bacterial and somatic cell count in raw milk were less at the sawdust barn than in tie stall barn. However, there was not significance difference between two barns. 4. The labour hour needed to cow management in the sawdust barn was approximately 48% of that of tie stall barn. 5. The temperature and moisture content measured in sawdust bed were closely affected by seasonal ambient temperature. The skin and hair of cow were much cleaner at the PVC light roofed sawdust barn than any other roof materials. 6. The additives used for improving of fermentation did not show any effect on temperature and moisture content in sawdust bed. When the ambient temperature was $30.4^{\circ}C$, the surface temperature of measured 1 cm above the sawdust bed was $12.2^{\circ}C$ lower and the temperature of 100 cm above the sawdust bed was $2.4^{\circ}C lower under shading net facility than that of vinyl roofed one.7. The hoof length of miking cow was 7.95 cm in tie stall and 9.19 cm in sawdust barn with high significance (P<0.01). And disease occurence such as mastitis and foot-rot tended to decrease in the sawdust barn. 8. The number of total bacteria and coliform bacteria were less in the sawdust bed compared with earth ground resting area. And a parasite strongyloides papillosus was detected but without any infected cow. 9. The nitrate($NO_3N$) content in non-roofed earth ground resting area and earth ground under the sawdust bed was likely to pollute the ground water. 10. In economic point of view, rice hull bedding barn was the cheapest among different systems. And in the sawdust bedding barn PVC light + slate roofed barn was most desirable, and vinyl roofed one the least.

• Journal of Veterinary Clinics
• /
• v.27 no.5
• /
• pp.522-532
• /
• 2010

The aims of the present study were to characterize the effect of glucocorticosteroids (GCs) on the normal canine skin and to evaluate the effect of a lipid mixture (LM), containing cholesterol, pseudoceramide, and free fatty acid, on the steroid-induced damaged skin of dogs. Five beagles were involved and the skin of the back of each dog was topically applied with four kinds of GCs twice daily for 28 days. LM was applied after that period of GCs application. Transepidermal water loss (TEWL), skin hydration, and skin pH were assessed during experimental periods and histopathological evaluation was performed. TEWL was significantly increased, with a maximum increase obtained on day 28 (p < 0.01). Skin pH was significantly decreased, with a maximum decrease obtained on day 28 (p < 0.01). Skin surface hydration was significantly increased on day 3, but values of skin hydration were progressively decreased and finally reached those of baseline. In histology, as results of steroid application, losses of keratin layers in the stratum corneum and edematous changes in the upper parts of dermis, and consequently, thickness of the epidermis and the stratum corneum were decreased. In addition, the numbers of hair follicles were markedly decreased in steroid control as compared to intact control. However, these skin atrophic changes were markedly inhibited by treatment of LM as compared with steroid control in the present study. Moreover, all biophysical parameters were reached to the baseline after LM treatment. These results showed that the topically applied GCs induced skin barrier impairment and a LM should be effective on repair of disturbed skin barrier function in dogs. Therefore, it is concluded that a LM tested in the present study is expected to treat the steroid-induced skin damages.

• Journal of Korean Society of Forest Science
• /
• v.54 no.1
• /
• pp.1-24
• /
• 1981

Kangweon-Do is rich in sightseeing resources. There are three sightseeing areas;first, mountain area including Seolak and Ohdae National Parks, and chiak Provincial Park; second eastern coastal area; third lake area including the watersheds of North Han River. In this paper, several methods of forestation were studied for landscaping the North Han River watersheds centering around Chounchon. In Chunchon lake complex, there are four lakes; Uiam, Chunchon, Soyang and Paro from down to upper stream. The total surface area of the above four lakes is $14.4km^2$ the total pondage of them 4,155 million $m^3$, the total generation of electric power of them 410 thousand Kw, and the total forest area bordering on them $1,208km^2$. The bordering forest consists of planned management forest ($745km^2$) and non-planned management forest ($463km^2$). The latter is divided into green belt zone, natural conservation area, and protection forest. The forest in green belt amounts to $177km^2$ and centers around the 10km radios from Chunchon. The forest in natural conservation area amounts to $165km^2$, which is established within 2km sight range from the Soyang-lake sides. Protection forest surrounding the lakes is $121km^2$ There are many scenic places, recreation gardens, cultural goods and ruins in this lake complex, which are the same good tourist resources as lakes and forest. The forest encirelng the lakes has the poor average growing stock of $15m^3/ha$, because 70% of the forest consists of the young plantation of 1 to 2 age class. The ration of the needle-leaved forest, the broad-leaved forest and the mixed forest in 35:37:28. From the standpoint of ownership, the forest consists of national forest (36%), provincial forest (14%), Gun forest (5%) and private forest(45%). The greater part of the forest soil, originated from granite and gneiss, is much liable to weathering. Because the surface soil is mostly sterile, the fertilization for improving the soil quality is strongly urged. Considering the above-mentioned, the forestation methods for improving landscape of the North Han River Watersheds are suggested as follows: 1) The mature-stage forest should be induced by means of fertilizing and tendering, as the forest in this area is the young plantation with poor soil. 2) The bare land should be afforested by planting the rapid growing species, such as rigida pine, alder, and etc. 3) The bare land in the canyon with moderate moist and comparatively rich soil should be planted with Korean-pine, larch, ro fir. 4) Japaness-pine stand should be changed into Korean-pine, fir, spruce or hemlock stand from ravine to top gradually, because the Japanese-pine has poor capacity of water conservation and great liability to pine gall midge. 5) Present hard-wood forest, consisting of miscellaneous trees comparatively less valuable from the point of wood quality and scenerity, should be change into oak, maple, fraxinus-rhynchophylla, birch or juglan stand which is comparatively more valuable. 6) In the mountain foot within the sight-range, stands should be established with such species as cherry, weeping willow, white poplar, machilus, maiden-hair tree, juniper, chestnut or apricot. 7) The regeneration of some broad-leaved forests should be induced to the middle forest type, leading to the harmonious arrangement of the two storied forest and the coppice. 8) For the preservation of scenery, the reproduction of the soft-wood forest should be done under the selection method or the shelter-wood system. 9) Mixed forest should be regenerated under the middle forest system with upper needle-leaved forest and lower broad-leaved forest. In brief, the nature's mysteriousness should be conserved by combining the womanly elegance of the lakes and the manly grandeur of the forest.