• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.194-196
• /
• 2005

Ultrasonic guided waves are gaining increasing attention for the inspection of platelike and rodlike structures. At the same time, inspection methods that do not require contact with the test piece are being developed for advanced applications. This paper capitalizes on recent advances in the areas of guided wave ultrasonics and noncontact ultrasonics to demonstrate a superior method for the nondestructive detection of thinning defects simulating hidden corrosion in thin aluminum plates. The proposed approach uses EMAT(electro-magnetic acoustic transducer) for the noncontact generation and detection of guided plate waves. Interesting features in the dispersive behavior of selected guided modes are used for the detection of plate thinning. It is shown that mode cutoff measurements provide a qualitative detection of thinning defects. Measurement of the mode group velocity can be also used to quantify of thinning depth.

• 산업경영시스템학회지
• /
• 제42권2호
• /
• pp.28-35
• /
• 2019

Since guided missiles with the characteristics of the one-shot system remain stored throughout their entire life cycle, it is important to maintain their storage reliability until the launch. As part of maintaining storage reliability, period of preventive test is set up to perform preventive periodic test, in this case failure detection rate has a great effect on setting up period of preventive test to maintain storage reliability. The proposed method utilizes failure rate predicted by the software on the basis of MIL-HDBK-217F and failure mode analyzed through FMEA (Failure Mode and Effect Analysis) using data generated from the actual field. The failure detection rate of using the proposed method is applied to set periodic test of the actual guided missile. The proposed method in this paper has advantages in accuracy and objectivity because it utilizes a large amount of data generated in the actual field.

• 비파괴검사학회지
• /
• 제28권2호
• /
• pp.211-216
• /
• 2008

이 연구에서 다층구조물에서 각 모드에 대한 위상속도, 군속도, 감쇠 그리고 파형구조를 구하는 프로그램을 개발하였다. 판의 수와 재료 물성치를 변화시키면서 각 모드의 파형구조를 얻었다. 유체가 닿아 있는 구조물에서 유도파를 이용한 비파괴 검사의 성공여부는 에너지 손실을 최소화하는 모드선정의 최적화이다. 이 연구에서는 자유표면판재의 표면에서 정규화된 두께방향의 변위가 감쇠의 변화를 예측하기 위해서 사용되었으며 감쇠와 파형구조의 관계를 밝혔다. 이것은 유도파의 감쇠를 물이 닿아 있는 경우 복소수근을 찾는 수학적 어려움을 경감하면서 자유표면에서 두께방향 변위의 변화로부터 손쉽게 얻을 수 있다. 이 연구를 통하여 다층구조물에서 보다 민감하고 효율적인 비파괴 검사를 위한 유도파의 모드선정의 최적화 개념을 완성했다.

• 비파괴검사학회지
• /
• 제29권6호
• /
• pp.570-578
• /
• 2009

Excitation and propagation of guided waves are very complex problems in pipes due to their dispersive nature. Pipes are commonly used in the oil, chemical or nuclear industry and hence must be inspected regularly to ensure continued safe operation. The normal mode expansion(NME) method is given for the amplitude with which any propagating waveguide mode is generated in the pipes by applied surface tractions. Numerical results are calculated based on the NME method using different sources, i.e., non-axisymmetric partial loading and quasi-axisymmetric loading sources. The sum of amplitude coefficients for 0~nineth order of the harmonic modes are calculated based on the NME method and the dispersion curves in pipes. The superimposed total field which is namely the angular profile, varies with propagating distance and circumferential angle. This angular profile of guided waves provides information for setting the transducer position to find defects in pipes.

• 비파괴검사학회지
• /
• 제29권5호
• /
• pp.442-449
• /
• 2009

스테인레스 스틸 배관의 결함에 대한 MsS의 비틀림모드 신호와 BEM 모델링의 SH모드 신호의 특성을 살펴보았다. 비틀림모드 신호와 SH모드신호의 비교를 위해 스테인레스 스틸 배관의 결함은 깊이와 폭을 달리하면서 원주방향으로 360도 가공하였다. MsS의 비틀림모드 신호분석 결과 원주방향 결함을 모두 탐지하였으며 깊이 변화에 따라 신호 진폭의 변화가 확인되었다. 하지만 원주방향 결함의 폭 변화는 일정한 경향이 나타나지 않았다. BEM 모델링의 SH 모드 신호 분석 결과 깊이 변화의 경우 비틀림모드 신호와 유사한 결과가 나타났지만, 폭 변화는 신호 진폭의 변화가 일어났다. 본 연구를 통하여 배관의 원주방향 결함에 대한 비틀림모드와 SH모드의 비교 분석을 통하여 신호 특성을 확인하였고 배관의 축대칭 결함에 대해 SH모드 모델링으로도 신호 예측이 가능함을 알 수 있었다.

• Structural Engineering and Mechanics
• /
• 제75권4호
• /
• pp.435-444
• /
• 2020

Ultrasonic guided wave testing is a very promising non-destructive testing method for rails, which is of great significance for ensuring the safe operation of railways. On the basis of the semi-analytical finite element (SAFE) method, a analytical model of 59R2 grooved rail was proposed, which is commonly used in the ballastless track of modern tram. The dispersion curves of ultrasonic guided waves in free rail and supported rail were obtained. Sensitivity analysis was then undertaken to evaluate the effect of rail elastic modulus on the phase velocity and group velocity dispersion curves of ultrasonic guided waves. The optimal guided wave mode, optimal excitation point and excitation direction suitable for detecting rail integrity were identified by analyzing the frequency, number of modes, and mode shapes. A sinusoidal signal modulated by a Hanning window with a center frequency of 25 kHz was used as the excitation source, and the propagation characteristics of high-frequency ultrasonic guided waves in the rail were obtained. The results show that the rail pad has a relatively little influence on the dispersion curves of ultrasonic guided waves in the high frequency band, and has a relatively large influence on the dispersion curves of ultrasonic guided waves in the low frequency band below 4 kHz. The rail elastic modulus has significant influence on the phase velocity in the high frequency band, while the group velocity is greatly affected by the rail elastic modulus in the low frequency band.

• 한국소음진동공학회논문집
• /
• 제24권4호
• /
• pp.324-331
• /
• 2014

The sensor configuration of the magnetostrictive guided wave system can be described as a single continuous transducing element which makes it difficult to separate the individual modes from the reflected signal. In this work we develop the mode decomposition technique employing chirplet transform based on the maximum likelihood estimation, which is able to separate the individual modes from dispersive and multimodal waveform measured with the magnetostrictive sensor, and estimate the time-frequency centers and individual energies of the reflection, which would be used to locate and characterize defects. Simulation results on a carbon steel pipe are presented, which show the accurate mode separation and more discernible time-frequency representation could become enabled using the proposed technique.

• 전자공학회논문지A
• /
• 제30A권2호
• /
• pp.29-35
• /
• 1993

A guided-wave TE to TM mode converter was demonstrated by using of the off-diagonal electrooptic coefficients in LiTaO$_{3}$. The input mode is coupled to the other orthogonal mode by the electrooptically induced off-diagonal polarizability. Compared with LiNbO$_{3}$, LiTaO$_{3}$ provides a smaller birefringence and thus a larger phase match period and larger optical bnadwidth. A novel electrode structure allowed a first-order Bragg-coupling phase matching. TE/TM mode conversion efficiency of 90% at 25 [V] was demonstrated with ${\lambda}$=0.63$\mu$m He-Ne laser.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.682-691
• /
• 1997

We have investigated the guided optical properties of a Ti:LiNbO$_3$optical waveguide which was fabricated by Ti-diffusion in an air atmosphere and proposed an effective polishing method of waveguide endfaces. And the results of guided optical mode and fabrication condition were obtained as follows; \circled1 propagation loss : 0.53 dB/cm \circled2 mode size : horizontal/vertical=12.5${\mu}{\textrm}{m}$ \circled3 mode mismatch : 1.7 dB \circled4 diffusion temperature : 105$0^{\circ}C$, time : 8 hours \circled5 atmosphere : air

• 한국광학회지
• /
• 제22권3호
• /
• pp.117-121
• /
• 2011

본 논문에서는 도파모드공진을 이용한 포화흡수체 반사기를 제안하였다. 포화흡수체로는 탄소나노튜브(CNT)를 사용하였다. 제안된 반사기는 CNT의 두께 변화 없이 modulation depth를 키울 수 있다는 장점이 있다. 제안하는 반사기의 fill factor(F)와 CNT의 두께변화에 따른 modulation depth, 대역폭, 포화되었을 때의 최대 반사율의 특징을 알아보았다. 제안된 반사기는 포화에너지를 줄일 수 있다는 장점이 있고, 100~200nm 얇은 CNT박막에서 50배정도 줄어드는 것을 확인 하였다.