• Journal of the Korean Solar Energy Society
• /
• v.29 no.5
• /
• pp.45-52
• /
• 2009

Fossil power plants firing lower grade coals or equipped with modified system for $NO_x$ controls are challenged with maintaining good combustion conditions while maximizing generation and minimizing emissions. In many cases significant derate, availability losses and increase in unburned carbon levels can be attributed to poor combustion conditions as a result of poorly controlled local fuel and air distribution within the boiler furnace. In order to develop a on-line combustion tuning system, field test was conducted at operating power boiler. During the field test the exhaust gases' $O_2,\;NO_x$ and CO was monitored by using a spatially distributed monitoring grid located in the boiler's high temperature vestibule and upper convective rear pass region. At these locations, the flue gas flow is still significantly stratified, and air in-leakage is minimal which enables tracing of poor combustion zones to specific burners and over-fire air ports. using these monitored information we can improving combustion at every point within the furnace, therefore the boiler can operate at reduced excess $O_2$ and gas temperature deviation, reduced furnace exit gas temperature levels while also reducing localized hot spots, corrosive gas conditions, slag or clinker formation and UBC. Benefits include improving efficiency, reducing $NO_x$ emissions, increasing output and maximizing availability. Discussion concerning the reduction of greenhouse gases is prevalent in the world. When taking a practical approach to addressing this problem, the best way and short-term solution to reduce greenhouse gases on coal-fired power plants is to improve efficiency. From this point of view the real time optimized combustion tuning approach is the most effective and implemented with minimal cost.

• The Plant Pathology Journal
• /
• v.35 no.2
• /
• pp.112-124
• /
• 2019

Barley worldwide is affected seriously by Fusarium seedling blight (FSB) and Fusarium head blight (FHB) diseases caused by the Fusarium species. The objective of this study was to facilitate the resistance of hulled and hull-less barley at different growth stages to F. culmorum according to direct parameters: disease rating (DR), fresh weight of leaves and roots, kernel weight per spike, kernel number per spike, plump kernels, and indirect parameters - chlorophyll a fluorescence (CF). Plate assay, greenhouse and field tests were performed on 30 spring barley doubled haploid (DH) lines and their parents infected with Fusarium culmorum. Direct parameters proved that hulled genotypes show less symptoms. Most studied chlorophyll a fluorescence (CF) parameters (apart from DIo/CS - amount of energy dissipated from PSII for laboratory test, TRo/CS - amount of excitation energy trapped in PSII reaction centers, ETo/CS - amount of energy used for electron transport and RC/CS - number of active reaction centres in the state of fully reduced PSII reaction center in field experiment) were significantly affected by F. culmorum infection. In all experiments, hulled genotypes had higher values of CF parameters compared to hull-less ones. Significant correlations were detected between direct and indirect parameters and also between various environments. It was revealed that ABS/CS, TRo/CS, and RC/CS have significant positive correlation in greenhouse test and field experiment. Significant correlations suggest the possibility of applying the CF parameters in selection of barley DH lines resistant to F. culmorum infection.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.4
• /
• pp.13-21
• /
• 2021

The feasibility of HWS for agricultural use was analyzed through a crop cultivation test to utilize the hydroponic waste solution (HWS) generated from the nutriculture greenhouse. The fertilizing effect of HWS was assessed on the basis of the inorganic nitrogen (N) mostly existed in HWSs, and nitrogen (urea) fertilizer. Lettuce was selected as the target crop influenced by the soil treatment and also for the crop cultivation test. Thus, the change in growth characteristics of lettuce and that in chemical characteristics of the soil were investigated. In terms of the growth of lettuce, the C control group with 70% nitrogen (urea) fertilizer and 30% HWS and the D control group with 50% nitrogen (urea) fertilizer and 50% HWS were more effective than the practice control group (B) with 100% nitrogen (urea) fertilizer. The results of this study confirmed the combined applicability of the chemical fertilizer and HWS for crop cultivation. Because NO₃-N present in HWS has a high possibility of leaching into the soil, its applicability as a fertilizer has been considered to be relatively low in Korea. However, if an appropriate mixing ratio of urea fertilizer and HWS could be applied, the problems associated with leaching of nitrate nitrogen could be reduced with beneficial effects on crop cultivation. Thus, future studies are required on the treatment effect of HWS with repeated cultivation, impact assessment on the surrounding environment, and appropriate fertilization methods using nitrogen (urea) fertilizer and HWS. These studies would facilitate the sustainable recycling of HWS.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.4
• /
• pp.33-41
• /
• 2021

The emission characteristics and emission factors were determined by measuring the concentration of methane (CH₄) and nitrous oxide (N₂O), the amount of ventilation, etc. in the two fattening rooms which have the same environment in winter. As a result of monitoring, the average concentration of CH₄ and N₂O was 20.7-26.7 ppm and 1.4-1.6 ppm. The average temperature inside the room was measured at 20.0-21.4℃, and the average ventilation was 1345.4-1567.3 m³/h. The daily emission of CH₄ for the first 30 days showed a constant emission of 3.6-8.2 g/d/m²/pig, but thereafter, the emission increased rapidly. The daily emission of N₂O was 0.7-1.3 g/d/m²/pig, showing stable emission during the test period, and relatively insignificant emission compared to the emission of CH₄. After repeated test, it was confirmed that there was no significant difference between the two rooms. As a result, the CH₄ 6. 21 g/d/m²/pig and N₂O 1.02 g/d/m²/pig average emission for each room was derived.

• Journal of People, Plants, and Environment
• /
• v.24 no.2
• /
• pp.195-207
• /
• 2021

Background and objective: While response measures to particulate matters in rural areas are limited due to poor inventory record keeping in the agricultural sector, it is necessary to control agricultural waste vinyl and the emission of precursors released from open burning and the secondary generation of particulate matters. Currently, the open burning emission calculation method uses the definition prescribed in CAPSS by the National Institute of Environmental Research. Methods: This study presented an open burning emission calculation formula for agricultural waste vinyl, which is included as agricultural waste. As for activity data, the open burning ratio of agricultural waste vinyl, and the annual incineration volume provided in the Status Survey by the Ministry of Agriculture, Food, and Rural Affairs were applied. The emission factor was generated through incineration tests on three agricultural plastic film samples collected by the Korea Environment Corporation. Results: Among precursors, SOx and NOx were selected and their emission features were monitored with incineration experiment infrastructure based on the EPA 5G method. The highest emission concentration by agricultural waste type was concentrated in the first and second quarters. As for emission factor of SO₂, it was calculated at 98.25 g/kg for mulching-use LDPE, 52.31 g/kg for greenhouse-use LDPE, and 14.40 g/kg for HDPE. As for NOx, it was calculated at 18.21 g/kg for mulching-use LDPE, 16.49 g/kg for greenhouse-use LDPE, and 10.67 g/kg for HDPE. Conclusion: This test confirmed the incineration features of PE-based plastics, ascertained the SOx emission factor that had not been included in open burning in the past, and established that low NOx emission concentration is interfered by soil mixed with livestock excretions. The findings from this study are expected to contribute to improving the system for controlling air pollutants in rural environments.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1108-1119
• /
• 2018

As the interest on the air pollution is gradually rising at home and abroad, automotive and fuel researchers have been studied on the exhaust and greenhouse gas emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emissions (regulated and non-regulated emissions, PM particle matter) and greenhouse gases of vehicle. Exhaust emissions and greenhouse gases of automotive had many problem such as the cause of ambient pollution, health effects. In order to reduce these emissions, many countries are regulating new exhaust gas test modes. Worldwide harmonized light-duty vehicle test procedure (WLTP) for emission certification has been developed in WP.29 forum in UNECE since 2007. This test procedure was applied to domestic light duty diesel vehicles at the same time as Europe. The air pollutant emissions from light-duty vehicles are regulated by the weight per distance, which the driving cycles can affect the results. Exhaust emissions of vehicle varies substantially based on climate conditions, and driving habits. Extreme outside temperatures tend to increasing the emissions, because more fuel must be used to heat or cool the cabin. Also, high driving speeds increases the emissions because of the energy required to overcome increased drag. Compared with gradual vehicle acceleration, rapid vehicle acceleration increases the emissions. Additional devices (air-conditioner and heater) and road inclines also increases the emissions. In this study, three light-duty vehicles were tested with WLTP, NEDC, and FTP-75, which are used to regulate the emissions of light-duty vehicles, and how much emissions can be affected by different driving cycles. The emissions gas have not shown statistically meaningful difference. The maximum emission gas have been found in low speed phase of WLTP which is mainly caused by cooled engine conditions. The amount of emission gas in cooled engine condition is much different as test vehicles. It means different technical solution requires in this aspect to cope with WLTP driving cycle.

• The Korean Journal of Pesticide Science
• /
• v.21 no.1
• /
• pp.84-89
• /
• 2017

This study was carried out to investigate residue dissipation of fluquinconazole and flusilazole in field-sprayed tomatoes during greenhouse cultivation and processing. The test pesticide, fluquinconazole+flusilazole 8.5 (7+1.5)% SC, was sprayed onto the tomatoes growing in a greenhouse according to Korea preharvest intervals and then samples were collected on 0 (3 hours after spraying), 1, 3, 5 and 7 days after last application for decline test. For processing test, tomatoes collected at harvest on 5 day after last application were processed to puree and juice. Limits of quantitation of fluquinconazole and flusilazole were 0.005 mg/kg in both tomatoes and their processed products. Recoveries for validation of the analytical methods for fluquinconazole and flusilazole in tomatoes and their processed products ranged from 74.8 to 97.5%. Biological half-lives of fluquinconazole and flusilazole in tomatoes under greenhouse conditions found to be 5.2 and 6.4 days, respectively. Average persistent residue levels of fluquinconazole and flusilazole were 37.34 and 79.53% after washing, 8.95 and 28.75% in filtrates after boiling, 3.58 and 14.66% in puree, and 3.34 and 13.52% in juice, respectively. These results indicated that the test pesticide residues on tomatoes could be largely removed through washing and boiling.

• Journal of Bio-Environment Control
• /
• v.30 no.4
• /
• pp.419-428
• /
• 2021

In order to develope a mobile-based greenhouse energy calculation program, firstly, the overall thermal transmittance of 10 types of major covers and 16 types of insulation materials were measured. In addition, to estimate the overall thermal transmittance when the cover and insulation materials were installed in double or triple layers, 24 combinations of double installations and 59 combinations of triple installations were measured using the hotbox. Also, the overall thermal transmittance value for a single material and the thermal resistance value were used to calculate the overall thermal transmittance value at the time of multi-layer installation of covering and insulating materials, and the linear regression equation was derived to correct the error with the measured values. As a result of developing the model for estimating thermal transmittance when installing multiple layers of coverings and insulating materials based on the value of overall thermal transmittance of a single-material, the model evaluation index was 0.90 (good when it is 0.5 or more), indicating that the estimated value was very close to the actual value. In addition, as a result of the on-site test, it was evaluated that the estimated heat saving rate was smaller than the actual value with a relative error of 2%. Based on these results, a mobile-based greenhouse energy calculation program was developed that was implemented as an HTML5 standard web-based mobile web application and was designed to work with various mobile device and PC browsers with N-Screen support. It had functions to provides the overall thermal transmittance(heating load coefficient) for each combination of greenhouse coverings and thermal insulation materials and to evaluate the energy consumption during a specific period of the target greenhouse. It was estimated that an energy-saving greenhouse design would be possible with the optimal selection of coverings and insulation materials according to the region and shape of the greenhouse.

• Korean Journal of Rural Living Science
• /
• v.8 no.1
• /
• pp.7-13
• /
• 1997

In this study we examined the greenhouse worker's work load to test the efficiency of the developed vehicles (hand operated vehicle (HV), simple battery-powered autonomous vehicle (AV)). The subject of this study were healthy adult females who had experience in growing crops. We measured workers' heart rate, blood Pressure. rectal temperature, mean skin temperature, oxygen consumption and blood lactate level as a physiological index of work load. The results of this study are as follows : The test group using experimental vehicle showed the lower heart rate (mean$\pm$S.D. for HV, AV respectively 74$\pm$5, 75$\pm$3 beats/min, p＜0.01) than the control group (84$\pm$8beat/min) not using experimental vehicle and the lower systolic blood Pressure (HV, AV respectively 109$\pm$8, 109$\pm$9 mmHg, p＜0.01) than the control group (121$\pm$11 mmHg), and lower rectal temperature(HV, AV respectively 37.0$\pm$0.1, 36.8$\pm$0.2$^{\circ}C$, p＜0.01) than the control group (37.0$\pm$0.2$^{\circ}C$), and the less oxygen consumption (HV, AV respectively 2.13$\pm$0.09, 1.66$\pm$0.52$m\ell$/kg/min, p＜0.01) than the control group(2.43$\pm$0.12$m\ell$/kg/min), and the lower blood lactate level (HV, AV respectively 2.03$\pm$1.00, 1.66$\pm$0.52mmol, p＜0.01) than the control group (2.43$\pm$0.12mmol). Judging from these results, these experimental vehicles for greenhouse workers can be confirmed as a useful tool. It is suggested that these vehicles would alleviate the peasant's syndrome including muscle fatigue and musculoskeletal disease usually caused by working in an uncomfortable posture.

• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.23-33
• /
• 1996

This study was performed to induce a quality improvement and standardization of materials used for greenhouse. For this purpose, physical and mechanical properties of agricultural films for greenhouse were measured by kinds and thickness of the films. The properties are composed of impact, tensile, tear propagation strength and light transmittance. The results were summarized as follows. 1. At the impact test result of the falling dart, the thicker the film, the greater the impact strength of soft film. The impact weight at 50 percents is from 158g to 213g and the strength of low density polyethylene(LDPE) film is higher than the rest of any other films. 2. Seeing the leveling of the impact rupture, maximum impact weight which was ruptured very little ranges from 62g to 192g. The impact strength of 0.1mm films was higher than that of 0.05mm as from 1.8 to 3.2 times. 3. Tensile weight covers from 0.95kg to 2.22kg in the test materials, and the weight of lengthwise film is larger than that of width. LDPE film has high value of tensile weight. Elongation range is from 345 to 102 percent and lengthwise elongation is greater than width as much as from 1.4 to 2.7 times. 4. Tea. propagation strength ranges from 80.5kg/cm to 121.7kg/cm, and unlike which of LDPE film has high value, EVA film has low value in the films tested. The width strength is higher than the lengthwise. 5. The light transmittance of the soft film is about 78-92 percent in the range of ultraviolet ray, but has high value in the visible ray range.