• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.63-70
• /
• 2015

PURPOSES: As a part of our research into repair techniques for roads that have collapsed as a result of a natural disaster, this study set out to find the optimum mix proportion for gravels to be used to restore a damaged area. METHODS: This study considered flow and strength-development characteristics. The experimental variables were the W/C ratio, the usage of the admixture, the types of cement, and the quantity of fine aggregate over three different experimental stages. The compressive strength was measured at 12 hours, one day, three days, and seven days. RESULTS : The flow varied with the amount of fine aggregate and the use of a high-range water-reducing (HRWR) admixture. The compressive strength also varied with respect to the type of cement and the W/C ratios. The strength satisfied the expected requirement of 21 MPa after one day, provided the mix proportion was appropriate. CONCLUSIONS: A gravel-filling high-flow cement-based mortar exhibited strength and consistency with a W/C ratio in the range of 0.40 to 0.45, assuming the use of HRWR at 0.5 to 0.7% and a fine aggregate/cement ratio of 1.0 to 1.5.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.2
• /
• pp.19-25
• /
• 2010

This study was conducted to determine the resilient modulus (Mr) and the unconfined compressive strength (UCS) of two recycled roadway materials such as recycled pavement material (RPM) and road surface gravel (RSG) with or without cement kiln dust (CKD). The recycled materials were blended with two CKD contents (5, 10 %) and 28 day curing time. Mr and UCS tests were also conducted after 10cycles of freezing and thawing to asses the impact of freeze-thaw cycling. Mr was determined conducting by the laboratory test method described by NCHRP 1-28A. Stabilized RPM and RSG had a modulus and a strength higher than unstabilized RPM and RSG. Mr and UCS of RPM and RSG mixed with CKD increased with increasing CKD content. The results indicated that the addition of CKD could be improved the strength and the stiffness of RPM and RSG. Therefore, RPM, RSG and CKD could be used as an effective materials in the reconstruction of roads.

• Geomechanics and Engineering
• /
• v.29 no.5
• /
• pp.583-598
• /
• 2022

The Compaction effect is important for evaluating the subgrade construction. However, there is little research exploring the compaction quality of deep soil using hydraulic compaction. According to reinforcement effect analysis, dimensional analysis is adopted in this work to analyze subgrade compactness within the effective reinforcement depth, and a prediction model is obtained. A hydraulic compactor is then employed to carry out an in-situ reinforcement test on gravel soil subgrade, and the subgrade parameters before and after reinforcement are analyzed. Results show that a reinforcement difference exists inside the subgrade, and the effective reinforcement depth is defined as increasing compactness to 90% in the depth direction. Layered compactness within the effective reinforcement depth is expressed by parameters including the drop distance of the rammer, peak acceleration, tamping times, subgrade settlement, and properties of rammer and filler. Finally, a field test is conducted to verify the results.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.10
• /
• pp.33-45
• /
• 2006

C.S.G is a material made by adding cement and water to rock-like material such as riverbed gravel or excavation muck that can be obtained easily near dam si. Recently, the use of C.S.G is gradually increasing as the construction material for dam, road, revement and so on. Commonly, the strength characteristics of C.S.G is affected by various influence factors such as grade, unit cement, age and water contents. In this study, a series of compaction test and unconfined compressive strength test were performed to investigate the relationship between a strength and influence factors such as three kinds of gradation, age, unit cement and water contents with riverbed gravel in Hwa Buk dam. The results show that strength Properties of C.S.G is variously affected by these influence factors. Especially, gradation and water contents are found to be very important factors fur determining the strength of C.S.G material. And, from the results of experimental study, the correlation equations between uncompressive strength and these factors are proposed.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.6
• /
• pp.697-704
• /
• 2008

Stormwater runoff from urban road area as non-point source has a tendency of including lots of pollutants at initial rain period. Recently, there are several cases of having installed treatment facilities for reducing pollution discharge from the impervious cover in urban area to prevent watershed environment from getting worse. The filtration type among non-point source treatment systems has been known as one of the most efficient system for treatment of non-point source pollutants. Therefore, various kinds of filter media such as expanded polypropylene(EPP), granular activated carbon, zeolite, perlite, illite, sand, gravel has been developed. This study was conducted to verify performance and hydraulic characteristics of filter media as measures for non-point source. The experiment was carried out to evaluate applicability and variation of 4 kind of most popular filter media(EPP, GAC, Zeolite, Perlite) in headloss with elapsed time and influent flow rate and to obtain data base that could be used to establish management plan for road runoff treatment. In experiment by tap water, it showed that EPP and perlite those are floatable materials showed stable operating performance and lower headloss than the others.

• Journal of Environmental Science International
• /
• v.14 no.6
• /
• pp.521-524
• /
• 2005

We introduce a simplified crossing wood drain disperses rain water concentration and is used to protect the road surface from erosion due to flooding over the unpaved road. The efficiency of a simplified crossing wood drain was also investigated. A structure of simplified crossing wood drain can be produced within 10 minutes and installed within 18 minutes. The cost of the this product is 1/5 of that of the existing crossing drain product. The production and installation cost can be reduced according to dexterity. In the context of such applications, the degrees of damage for a rubber pad, which preventing the rain overflow, were varied according to their materials. A type of 8.2mm thick fabric rubber was the most suitable in this study.

• Journal of Korean Society on Water Environment
• /
• v.37 no.4
• /
• pp.286-295
• /
• 2021

The removal efficiency of road-deposited sediment (SDR) by road sweeping was analyzed by performing particle size analysis before and after road sweeping at four highways during May to December 2019. The SDR accounted for the largest proportion in the range of 250 to 850 ㎛ and the degree of its proportion had an effect on the particle size distribution curve. The particle size distribution of the collected sediments showed a similar distribution at all sites. Below 75 ㎛, the removal efficiency of SDR showed a constant value around 40%, but above 75 ㎛, it increased as the particle size increased. The removal efficiency was 82-90% (average 86%) for gravel, 66-93% (average 79%) for coarse sand, 35-92% (average 64%) for fine sand, 29-69% (average 44%) for very fine sand, 19-58% (average 40%) for silt loading, 10-59% (average 40%) for TSP, 13-57% (average 40%) for PM10, and 15-61% (average 38%) for PM2.5. SDR removal efficiency showed an average of 69% for the four highways. It was found that if the amount of SDR was less than 100 g/m², it was affected by the road surface condition and had a large regional deviation. As such, the amount of SDR and the removal efficiency increased. The fine particles, which have relatively low removal efficiency, contained a large amount of pollutants, which is an important factor in water and air pollution. Therefore, various measures to improve the removal efficiency of fine particles in SDR by road sweeping are needed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.93-98
• /
• 2020

Washboarding is a phenomenon in which a wavy shape occurs periodically and naturally on an unpaved road made of soil or gravel. This phenomenon causes high-frequency vibration of the traffic traveling on the road because of the height difference of the wave pattern, which may lead to vehicle failure. Consequently, associated research is needed concerning vehicle safety. Therefore, in this study, a numerical simulation was conducted using the discrete element method, which is often used for powder simulation. In contrast to previous studies, the results of this study demonstrate that washboarding can occur even in an environment of 1.5 m/s or less. However, the amount of washboarding is minimal. The study revealed that washboarding develops over time, such that sufficient development time is required before measurements are taken.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.39-48
• /
• 2006

A laboratory investigation was conducted wherein smooth, rounded, siliceous river gravel aggregates were coated with fine-grained polyethylene, carpet co-product, or cement + styrene butadiene rubber latex and used to prepare hot mix asphalt concrete specimens. Only the coarse (+ No.4) aggregates were coated. The concept was that the coatings would enhance surface roughness of the aggregates and, thus, produce asphalt mixtures with superior engineering properties. Hot mix asphalt specimens were prepared and evaluated using several standard and non-standard test procedures. Based on experiences during the coating processes and analyses of these limited test results, the following was concluded: All three aggregate coating materials increased Hveem and Marshall stability, tensile strength, and resilient modulus(stiffness). These findings are indicative of improved resistance to rutting and cracking in hot mix asphalt pavements prepared using coated gravel aggregates in comparison to similar uncoated gravel aggregates.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.113-121
• /
• 2011

Rollover accident is one of the serious traffic accident and rollover accident takes high portion of all accident. The most common type of rollover is a tripped rollover which occupy 95% of all type of single-vehicle rollover. Tripped rollover occurs when a vehicle leaves normal road way and tripped by loose gravel, soil of fixed object such as guard rail, curbs and ditches. And the rest of the type of rollover is un-tripped rollover. An un-tripped rollovers that occurs during high-speed collision avoidance maneuvers. In this paper, presents the explanation of the un-tripped rollover test method and procedure, additionally this paper deals with various occurrence in the un-tripped test such as occurring excessive tire camber in the un-tripped test, tire side-wall contact with road surface and roll oscillation. And this paper analyzes the analysis of the roll rate amplitude in specific frequency through the FFT (Fast Fourier Transform) and the roll angle at the steering reverse timing which is the Fishhook test roll rate feedback time. Finally, this paper analyzes the relations between the estimated steady state roll gain and rollover stability.