• 한국도로학회논문집
• /
• 제17권5호
• /
• pp.11-18
• /
• 2015

PURPOSES : The purpose of this study is to develop a deicing pavement system using carbon fiber or graphite with high electrical conductivity and thermal conductivity. METHODS: Based on literature reviews, in general, conventional concrete does not exhibit electrical and thermal conductivity. In order to achieve a new physical property, experiments were conducted by adding graphite and carbon fiber to a mortar specimen. RESULTS: The result of the laboratory experiment indicates that the addition of graphite can significantly reduce the compressive strength and improve the thermal conductivity of concrete. In the case of carbon fiber, however, the compressive strength of the concrete is slightly increased, whereas, the thermal conductivity is slightly decreased against the plain mortar irrespective of the length of the carbon fiber. In addition, a mixture of the graphite and carbon fiber can greatly improve the degree of heating test. CONCLUSIONS : Various properties of cement mortar change with the use of carbon fiber or graphite. To enhance the conductivity of concrete for deicing during winter, both carbon fiber and graphite are required to be used simultaneously.

• Korean Chemical Engineering Research
• /
• 제55권2호
• /
• pp.264-269
• /
• 2017

피치계 흑연섬유의 발열특성을 향상시키기 위하여 흑연섬유에 무전해법을 이용하여 구리 도금하였다. 구리 도금된 흑연섬유는 공기 분위기에서 열중량분석법을 실시하여 도금 시간에 따라 흑연섬유 표면에 구리가 도입된 양을 계산하였다. 또한, 전압에 따른 발열 온도는 섬유 가닥을 이용하여 열화상카메라로 관찰하였다. 무전해 도금의 시간이 증가함에 따라 도입된 구리의 양은 증가하였다. 20분 동안 무전해 도금한 섬유의 전기 전도도는 1594.3 S/cm이며, 발열 온도는 최대 $57.2^{\circ}C$로 가장 크게 나타났다. 이러한 결과는 도금시간이 증가함에 따라 전기 전도성이 우수한 구리가 흑연섬유 표면에 성장하고, 이에 따라 발열특성이 향상된 것으로 판단된다.

• 한국세라믹학회지
• /
• 제30권10호
• /
• pp.797-802
• /
• 1993

Graphite fiber intercalated compound was deintercalated at $25^{\circ}C$, 65% of humidity and its deintercalated compound was discussed, based on the X-ray diffraction analysis, electrical resistivity measurement, and UV/VIS spectrometer measurements. During deintercalation, the structure was changed in orderlongrightarrowdisorderlongrightarroworder, and resistivity was decreased in the disorder state of the structure, which reflectance minimum of the UV/VIS spectrum ranged from 660 to 750nm (1.88~1.65eV).

• 한국응용과학기술학회지
• /
• 제31권4호
• /
• pp.679-687
• /
• 2014

본 연구에서는 캐비테이션에 의한 부식에 강한 도료를 개발하기 위하여 고탄성의 우레탄 수지에 내마모 성능을 향상시키기 위한 첨가제로서 Multi wall과 Single wall type의 Carbon nano tube(CNT)와 Spherical과 Fiber type의 Graphite 나노 입자를 첨가하여 물성과 캐비테이션에 대한 저항성, 작업성 등을 비교 평가하였다. 나노 입자로서 Graphite에서는 캐비테이션 저항성($t_{50}$)이 Spherical type($t_{50}$ 182min)보다는 Fiber type($t_{50}$ 292min)이 높은 캐비테이션 저항성을 갖는 것으로 관찰되었다. 또한 CNT에서는 Single wall type의 캐비테이션 저항성($t_{50}$ 286min)이 Multi wall보다는 더 높은 것으로 관찰되었다. 나노 입자중에서 가격 및 캐비테이션 저항성을 감안하면 가장 최적의 나노 입자는 Fiber type의 Graphite로 관찰되었다. 도료의 작업성 평가에서 수동 작업에 의해 제작된 표면은 매끈한 표면을 가지고 있으나 Spray 작업에 의해 제작된 표면은 표면이 균일하지 않으며 Spray시 발생된 Dust가 표면에 고착된 형태로 관찰되었다.

• Composites Research
• /
• 제19권2호
• /
• pp.7-12
• /
• 2006

본 연구에서는 탄소섬유의 첨가가 흑연 보강 전도성 고분자 복합재료의 전기적, 기계적 특성에 미치는 영향을 고찰하였다. 압축성형법을 이용하여 흑연입자/탄소섬유 혼합 보강 전도성 고분자 복합재료를 제조하였으며 흑연입자의 고비율 충진은 복합재료 내에서 입자 사이의 직접 접촉을 통해 높은 전기 전도도(>100S/cm)를 얻는 것을 가능하게 하였다. 하지만 흑연입자의 비율이 높아짐에 따라 소재의 강도가 점차 떨어지게 되므로 이를 보완하기 위해 탄소섬유를 첨가하여 그에 따른 소재의 전기적, 기계적 특성 변화를 연구하였다. 탄소섬유의 충진 비율이 증가함에 따라 소재의 굽힘 강도는 증가하였으나 탄소섬유의 클러스터 형성으로 인해 탄소섬유 사이에 비전도성 영역이 발생하여 복합재료의 전기 전도도는 감소함을 확인하였다. 탄소섬유의 충진 비율이 전체 시스템의 20wt.%인 경우에는 굽힘 강도는 12% 증가한 반면 전기 전도도가 27% 감소하였다.

• Tribology and Lubricants
• /
• 제5권2호
• /
• pp.94-100
• /
• 1989

Friction and Wear behavior of continuous graphite fiber composites was studied for different fiber orientations against the sliding direction. The effect of fiber orientation on friction and wear of the composite and on the deformation of the counterface was investigated experimentally. Pin on disk type testing machine was built and employed to generate the friction and wear data. A graphite fiber composite plate was produced by the bleeder ply molding in an autoclave and machined into rectangular pin specimens with specific fiber orientations, i.e., normal, transverse, and longitudinal directions. Three different wear conditions were employed for two different periods of time, 24 and 48 hours. The wear track of the worn specimens and the metal counterface was examined with a scanning electron microscope (SEM) to observe the damaged fibers on the surface and wear film generation on the counterface. Wear mechanism of the composite during sliding wear is proposed based on the experimental results.

• 한국수소및신에너지학회논문집
• /
• 제25권2호
• /
• pp.131-138
• /
• 2014

Highly conductive bipolar plate for polymer electrolyte membrane fuel cell (PEMFC) was prepared using phenol novolac-type epoxy/graphite powder (GP)/carbon fiber filament (CFF) composite, and a rubber-modified epoxy resin was introduced in order to give elasticity to the bipolar plate graphite fiber (GF) was incorporated in order to improve electrical conductivity. To find out the cure condition of the mixture of novolac-type and rubber-modified epoxies, differential scanning calorimetry (DSC) was carried out and their data were introduced to Kissinger equation. And tensile and flexural tests were carried out using universal testing machine (UTM) and the surface morphology of the fractured specimen and the interfacial bonding between epoxy matrix and CFF or GF were observed by a scanning electron microscopy (SEM).

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.88-91
• /
• 2011

Glass fiber drawing from a silica preform is one of the most important processes in optical fiber manufacturing. High purify silica preform of cylindrical shape is fed into the graphite furnace, and then a very thin glass fiber of 125 micron diameter is drawn from the softened and heated preform. A computational analysis is performed to investigate the heat transfer characteristics of preform heating and the glass fiber drawing in the furnace. In addition to the dominant radiative heating of preform by the heating element in the furnace, present analysis also includes the convective heat transport by the gas flowing around the preform that experiences neck-dawn profile and the freshly drawn glass fiber at high fiber drawing speed. The computational results present the effects of gas flow on the temperature of preform and glass fiber as well as the neck-down profile of preform.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1991년도 제1차 학술발표초록집
• /
• pp.34-34
• /
• 1991

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.181-187
• /
• 1995

The effet of glass fiber and graphite on the wear properies in tin-bronze alloy matrix composites was studied by a pin-on-disk type wear testing machine. The results obtained from the wear test were analized by SEM observations of worn surfaces of pins and disks and EPMA composition measurments. The amount of wear was devreased as increasing the content of glass fiber in matrix, since the alloy matrix was reinforced by glass fibers. The wear mechanism of the matrix specimen without glass fibers was proved as the contact area delamination. Oxide layer formed on sliding surface led to the increasing wear resistance. Specimens containing graphite particles showed an lubrication effect to counter disks.