• Advances in materials Research
• /
• v.12 no.4
• /
• pp.331-349
• /
• 2023

Foam concrete can be considered as environmental friendly material due to its low weight, its minimal cost and a possibility to add waste materials in its production. This paper investigates the possibility of producing foam concrete with waste glass as powder and aggregate. Then, the effect of using waste glass on strength and drying shrinkage of foam concrete was examined. Also, the effect of incorporating polypropylene fibers (12 mm length and proportion of 0.5% of a mix volume) on distribution of waste glass as coarse particles within 1200 kg/m³ foam concrete mixes was evaluated. Waste glass was used as powder (20% of cement weight), as coarse particles (25%, 50% and 100% instead of sand volume) and as fine particles (25% instead of sand volume). From the results, the problem of non-uniform distribution of coarse glass particles was successfully solved by adding polypropylene fibers. It was found that using of waste glass as coarse aggregate led to reduce the strength of foam concrete mixes. However, using it with polypropylene fibers in combination helped in increasing the strength by about 29- 50% for compressive and 55- 71% for splitting tensile and reducing the drying shrinkage by about (31- 40%). In general, not only the fibers role but also the uniformly distributed coarse glass particles helped in improving and enhancing the strength and shrinkage of the investigated foam concrete mixes.

• Elastomers and Composites
• /
• v.56 no.2
• /
• pp.85-91
• /
• 2021

In this study, different types and shapes of various particles produced on the asphalt pavement road were analyzed. Road dust at a bus stop was collected and was separated as per their sizes by using a sieve shaker. Tire-road wear particles (TRWPs), asphalt pavement wear particles (APWPs), mineral particles, plant-related particles, glass beads, glass particles, road paint wear particles, plastic particles, and fibers were observed herein. The types and shapes of the particles varied depending on their sizes. TRWPs larger than 500 ㎛ were not observed. TRWPs with a size of 212-500 ㎛ were rarely present, but many TRWPs with a size smaller than 212 ㎛ were observed. APWPs were observed for whole-particle sizes of below 1,000 ㎛. A variety of particles on the road would lead to lower friction between the tires and the road, thereby increasing the braking distance of vehicles. Most of the particles include mineral particles, glass particles, and APWPs with rough surfaces. Therefore, the abrasion of the tire tread would accelerate owing to friction with the tough particles.

• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.14 no.2
• /
• pp.166-172
• /
• 2007

Purpose: The purpose of this study was to examine the factors influencing glass particle contamination in single dose glass ampules upon opening. Method: The study was single case experimental design. Different methods of opening ampule (hand, wooden stick), different sizes of ampules(1cc, 2cc) and different sizes of needles(17gauge, 23gauge, $5{\mu}m$ filter) were evaluated. Eighteen ampules were randomly assigned in each group. The number of glass ampule particles ${\ge}10{\mu}m$ was counted by microscope. Results: There was no significant difference in the number of particles aspirated by opening methods. But number of glass particles was much lower when using 1cc ampules rather than 2cc ampules and was also much lower when using smaller size needles and needles which include a $5{\mu}m$ filter rather than larger size of needles. Conclusion: We suggest that larger bore or unfiltered needles increase the risk of aspirating more glass particles than smaller bore or filter needles. In addition, these data show that a wooden stick can be used as a method opening glass ampules.

• Proceedings of the Korean Ceranic Society Conference
• /
• 1986.12a
• /
• pp.259-267
• /
• 1986

The sintering behavior of silver-oxide glass composite thick-film has been studied with varing glass content. It is shown that during heat treatment glass became liquid phase to deeply affect the microstructure development of the silver particles and to control the physical properties of the thick-films. As glass content increased, the initial repacking of silver particles took place rapidly but the homogeneities of the microstructure showed different features. When the glass content was over some range, the silver particles exuded glass to decrease net energy and glass formed liquid pools separated from the solid skeletons. Finally the relations between the microstructures and electrical properties of the thick-film were discussed.

• Korean Journal of Materials Research
• /
• v.31 no.1
• /
• pp.54-59
• /
• 2021

In this work, narrow-band green-emitting CsPbBr3 particles are embedded in commercialized glass composites by a facile dry process. By optimizing the method through sintering in glass frit (GF) composites including CsBr and PbBr2, used as precursors, the encapsulation of CsPbBr3 particles made them waterproof with green fluorescence. To improve the fluorescent properties by reducing aggregation of CsPbBr3, fumed silica (FS) is additionally used to help particles avoid bulking up in the glass matrix. The CsPbBr3 perovskite/glass composites are characterized using scanning electron microscopy (SEM) images and energy-dispersive X-ray spectroscopy (EDS) maps, which support the existence of CsPbBr3 particles in the glass matrix. The photoluminescence (PL) properties demonstrate that the emission spectrum peak, full width at half maximum (FWHM), and photoluminescence quantum yield (PLQY) values are 519 nm, 17 nm, and 17.7 %. We also confirm the water-resistant properties. To enhance water/moisture stability, the composite sample is put directly into water, with its PLQY monitored periodically under UV light.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.166-180
• /
• 1992

One disadvantage of Glass Ionomer Cement Restoration is the difficulty in polishing. To find the appropriate polishing method, we polished the surface of Glass Ionomer Cement Restorations by 11 combination methods serially using disks shared with large-small particles and evaluated the polishing process in terms of surface roughness, surface roughness curve, and SEM findings. In addition, a visible light curing type bonding material was applied to evaluate the possible improvement in surface properties. The following results were obtained. 1. The disk surface of Glass Ionomer Cement was polished serially by disks with superfine particles, but it didn't become smooth. 2. The surface of Microfilled Composite resin became smoother as using a disk with finer particles. 3. When a visible light curing type bonding material was applied in finishing process, the surface of Glass Ionomer Cement became smooth as much as the applied matrix.

• Analytical Science and Technology
• /
• v.29 no.3
• /
• pp.136-141
• /
• 2016

In the present study, the distribution of glass particles inside 10 patrol cars of Chungnam Province has been studied. The target seats were front seats (driver’s seat, passenger’s seat) and the back seat. The target areas were the bottom of the seat (seat contacting buttocks, back of the seat, and the corner of the seat (the bottom and back attached part)). The target areas were tape lifted with an adhesive tape. The glass particles adhering to the adhesive tape were examined and counted under a stereomicroscope. The total number of glass particles found was 679. Among them, 471 (driver’s seat 293, passenger seat 178) were collected from front seats, which are usually occupied by police officers. The majority of glass particles were under 0.49 mm size. The results show that the majority of glass particles can be found on the front seats, rather than on the back seat. There is a high probability that glass particles found on the front seat adhere to police officers, so that to get further transferred to the convict upon physical contact (secondary transfer). Thus, there is a risk of misinterpretation of the value of glass evidence in the course of forensic examinations. Hence, a separate method to prevent cross contamination has to be prepared by police authorities as soon as possible.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.1
• /
• pp.23-26
• /
• 2012

A zero-shrinkage sintering process in which the shrinkage of x-y axis is controlled to be zero is in great demand due to the trend of high integration in the ceramic modules. Among the zero-shrinkage sintering processes that are available, the proposed glass infiltration method where the viscous but fluidic glass infiltrates of the $Al_2O_3$ particles in the structure of $Al_2O_3$/glass/$Al_2O_3$ during firing is one of the applicable methods. However, the above proposed glass infiltration method has the problem of the warpage-like delamination. This occurred at the outermost surface of the multiple-bundle substrate. It is thought that the decomposed gas rapidly expands in low viscous glass to create vacant space. To solve this problem, the vacant space was tamped with $Al_2O_3$ particles to lead to the actual improvement of the sintered properties. With 15 wt% of tamping $Al_2O_3$ particles in glass, most of the vacant space disappeared. Fully densified zero-shrinkage substrate without delamination can be obtained.

• Journal of Periodontal and Implant Science
• /
• v.29 no.1
• /
• pp.173-192
• /
• 1999

The purpose of this study was to evaluate the effects of bioactive glass and natural coral on the human periodontal ligament fibroblast(HPLF) behaviors during the regeneration process of peridontium. To determine the cellular events occuring in the presence of the particles of bioactive glass and natural coral, HPLF were isolated from healthy premolar teeth extracted for orthodontic treatment. Cells were cultured in ${\alpha}$MEM at 37$^{\circ}C$, 5% $CO_2$, 95% humidity incubator. Bioactive glass and natural coral were powdered, and each particles(<40${\mu}$m) were placed on the cultured cells at the concentration of 0.3mg/ml, and 1,0mg/ml for experimental group. In control group no particles were added. And each group was evaluated by examining the cell morphology under phase-contrast micrograph at 4 day and transmission electron micrograph(TEM) and scanning electron micrograph(SEM) at 14 day, alkaline phosphatase activity at 5 and 9 day, protain synthesis at 4 day, DNA synthesis at 1, 2, 3 and 4 day, cell proliferation at 1, 3, 5,7 and 9 day and the formation of bone nodule at 30 day after culturing all groups in mineralizing supplemented mediun, No significant changes in cell morphology by adding these two matirials were found under phase contrast microscopy and TEM. HPLF phagocytocized each particles suggesting that HPLF is involved in the process of resorbing each particles and that bioactive glass were more biocompatible than natural coral. The ALPase activity of bioactive glass 0.3 mg/ml was similar with control groups and all the rests of control groups were significantly low(P<0.01) indicating a transient dedifferentiation of HPLF in the presence of bioactive glass and natural coral particles. There were no significant differences of protein synthesis between all groups. The DNA synthesis in experimental groups were significantly lower than control groups at 1, 2 and 3 day (P<0.01) but became similar to control groups at 4 day. Between control groups, the DNA synthesis in bioactive glass O.3mglml group was significantly higher than other groups(P<0.01). Cell proliferation in natural coral 1.0mg/ml and bioactive glass 1.0mglml groups were significantly lower than control group at 3 day(P<0.05) and there were no differences at 5, 7, 9 day. There were more bone nodule formation in experimental groups than in control groups. In conclusion, these results indicated that bioactive glass and natural coral have some effects of a transient dedifferentiation on HPLF and regeneration of periodontal tissues, however any significant cytotoxic effect on HPLF by these two particles were not found.

• Journal of Information Display
• /
• v.13 no.4
• /
• pp.139-143
• /
• 2012

In this study, optical simulation was used to compare three optical structures that could be applied to the typical organic light-emitting diode to increase the outcoupling efficiency. These were spherical scattering particles (treated as Mie scatterers) embedded in the glass substrate, microlenses formed on the glass substrate, and a diffusing layer (DL) with a Gaussian scattering distribution function inserted between the indium tin oxide (ITO) and the glass substrate. It was found that the application of microlens array and that of scattering particles in the glass substrate exhibited similar enhancements in the outcoupling efficiency when the density and the refractive index of the scattering particles were optimized. The DL located at the interface between the glass and the ITO further enhanced the efficiency because it could further extract the trapped light in the waveguide mode. The appropriate combination of these three structures increased the outcoupling efficiency to about 42%, which is much greater than the typical values of 15-20% when there is no optical structure for light extraction.