• Composites Research
• /
• v.26 no.6
• /
• pp.380-385
• /
• 2013

Characteristics of delamination factor and surface roughness by drilling condition for glass fiber reinforced plastic (GFRP) composites were investigated in this paper. An expression to quantify the delamination factor was induced by using image pixels of the entry and the experimental drilling was accomplished by fabricating several GFRP specimens in condition of minimizing the effect of vibration and heat. A method for measuring 6 points average surface roughness was applied to acquire the more reliable roughness values. The experimental results showed that the delamination factor was decreased as the feed rate was increased and it was also slightly decreased as the cutting speed was increased. Also, it was investigated that the surface roughness at inner surface of drilled holes was increased as the feed rate was increased, whereas the roughness values were not affected by the cutting speed variation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.896-899
• /
• 2002

Microcellular foaming Process has several merits, impact strength elevation, thermal insulation, noise insulation, and raw material saving etc. This method make the glass transition temperature of polymers low, and diminish the residual stress of polymers. This characteristics of Microcellular foaming process influences the physical properties of recycled polymers. This paper describes about the impact strength change of Microcellular foamed recycled ABS.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1103-1107
• /
• 2005

Single-crystal silicon thin films on glass (SOG) and on fused-quartz (SOQ) were prepared using wafer bonding and hydrogen-induced layer transfer. Thinfilm transistors (TFTs) were subsequently fabricated. The high-temperature processed SOQ TFTs show better device performance than the low-temperature processed SOG TFTs. Tensile and compressive strain was measured respectively on SOQ and SOG. Consistent with the tensile strain, enhanced electron effective mobility was measured on the SOQ TFTs.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.286-286
• /
• 2004

초고속 정보통신망 구현에 필수적인 광학 연결용 부품인 광 Ferrule은 광섬유 커넥터의 중요부품으로서 우수한 치수정밀도와 내마모성을 갖추어야 한다. 현재, Ferrule로 사용되는 재료는 지르코니아, 알루미나 등 세라믹 물질이 많이 사용되고 있으며 기계적 강도나 내마모성 면에서는 우수하지만, 피연마속도가 석영섬유에 비해 현저히 작아서 특수한 연마방법을 채택해야 하며 성형성이나 가공성이 나빠 생산효율이 낮고 비용이 비싸다는 단점을 가지고 있다.(중략)

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2004.10a
• /
• pp.50-61
• /
• 2004

Nowadays Laser Controllable Thermo-cleaving is the most promising method of cutting FPD(Flat Panel Display) glass in mass-production line. And this method can be used to cut other brittle materials such as quartz, sapphire, ceramic and semiconductor. The concept of this method is shown in Picture 1. Laser beam heats glass up to strain point not to melting point and cooling system chills glass to make maximum thermal stress in glass and then the thermal stress generates micro thermal crack in other words blind crack. Laser Controllable Thermo-cleaving controls the thermal stress to optimize the blind crack up to level of mass-production line.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.310-320
• /
• 2007

Statement of the problem. The fracture of acrylic resin dentures remains an unsolved problem. Therefore, many investigations have been performed and various approaches to strengthening acrylic resin, for example, the reinforcement of heat-cured acrylic resin using glass fibers, have been suggested over the years. But problems such as poor workability, rough surface, poor adhesion of glass fiber resin complex are not solved yet. Purpose. The aim of the present study was to investigate the effect of short glass fibers on the transverse strength of heat-polymerized denture base acrylic resin and roughness of resin complex after abrasion test. Material and methods. To avoid fiber bunching and achieve even fiber distribution, glass fiber bundles were mixed with acrylic resin powder in conventional mixer with a non-cutting blade, to produce the glass fiber($10{\mu}m$ diameter, 3mm length, silane treated) resin composite. Glass fibers were incorporated at 0%, 3%, 6% and 9% by weight. Transverse strength were measured. After abrasion test, surface roughness was evaluated and scanning electron microscope view was taken for clinical application. Results. 1. 6% and 9% incorporation of 3mm glass fibers in the acrylic resin enhanced the transverse strength of the test specimens(p<0.05). 2. Before abrasion test, incorporation of 0%, 3%, 9% glass fiber in the resin showed no dirrerence in roughness statisticaly(p>0.05). 3. After abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically(p>0.05). 4. In SEM, surface roughness increased as the percentage of the fibers increased. 5. In the areas where glass fiber bunchings are formated, a remarkably high roughness was noticed. Conclusion. 6% and 9% addition of silane-treated short glass fibers into denture base acrylic resin increased transverse strength significantly. Before and after abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically.

• The Journal of Korean Academy of Prosthodontics
• /
• v.16 no.1
• /
• pp.32-37
• /
• 1978

The purpose of this study was to apply the position, the form and the angle of the attrition in the natural maxillary central incisors shown on the labial surface to the artificial teeth in the field of prosthetic dentistry. So we should exactly alter the molds of artificial teeth in individual cases in order to make artificial teeth more natural. 226 extracted teeth of the maxillary central incisors were chosen as materials. I have exactly examined the teeth with a magnifying glass and a circular graduator under concentrated light. The observation brought me the following results: 1) The attrition was most prevailing at the range from the mesial angle to the middle part of cutting edge in the left maxillary central incisor, and distal angle of cutting edge in the right maxillary central incisor. 2) On the attrite form of both angles, the angulated form was more than 4 times as frequent as rounded form in the mesial angle, and almost equal in the distal angle. 3) On the attrite form of cutting edge, mesial attrite form including mesial angle was most frequent in the left maxillary central incisor, and distal attrite form including distal angle in the right maxillary central incisor. 4) The angle made by the labial surface and the attrite surface was about $39^{\circ}$, and more than 70% of the total examined teeth were included at the range from $31^{\circ}\;to\;50^{\circ}$. 5) None attrite form at the cutting edge was about 12% and completely attrite form at the cutting edge was about 27% of examined teeth.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.5
• /
• pp.533-551
• /
• 2015

The rock fracturing during waterjet cutting is very complicated because rock is inhomogeneous and anisotropic, compared with artificial materials (e.g., metal or glass). Thus, it is very important to verify the effects of rock properties on waterjet rock cutting performance. Properties affecting the rock cutting efficiency have been variously described in the literature, depending on the experimental conditions (e.g., water pressure, abrasive feed rate, or standoff distance) and rock-types studied. In this study, a rock-property-related literature review was performed to determine the key properties important for waterjet rock cutting. Porosity, uniaxial compressive strength, and hardness of the rock were determined to be the key properties affecting waterjet rock cutting. The results of this analysis can provide the basic knowledge to determine the cutting efficiency of waterjet rock cutting technology for rock excavation-related construction.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.22-26
• /
• 2010

Recently, due to the tremendous growth of media technology, demands of the aspheric glass lens which is a high-performance and miniaturized increase gradually. Generally, the aspheric glass lens is manufactured by Glass Molding Press (GMP) method using tungsten carbide (WC) mold core. In this study, the thermal deformation which was occurred by GMP process was analyzed and applied it to compensate the aspheric glass lens. The compensated lens was satisfied that can be applied to the actual specifications.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.585-590
• /
• 2002

Abrasive water-jet(AWJ) machining is a new cutting technology. The AWJ can cut various materials touch as metal, glass and stone. However, the AWJ machining makes troubles including kerf, rounding and side taper. In this study, we investigated the correlation between parameters of abrasive water-jet machining arid cutting characteristics. The machining parameter were the material thickness and the traverse speed. The experiment was conducted to cut the stainless steel(STS41) and the mild steel(SS41) specimens. The results of the experiment weirs presented as the relation between cutting conditions and trouble of a dimension error, a conner error, an uncut width and a kerf.