• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.731-744
• /
• 2007

A method for dynamic analysis and design calculation of a Powertrain Mounting System(PMS) including Hydraulic Engine Mounts(HEM) is developed with the aim of controlling powertrain motion and reducing low-frequency vibration in pitch and bounce modes. Here the pitch mode of the powertrain is defined as the mode rotating around the crankshaft of an engine for a transversely mounted powertrain. The powertrain is modeled as a rigid body connected to rigid ground by rubber mounts and/or HEMs. A mount is simplified as a three-dimensional spring with damping elements in its Local Coordinate System(LCS). The relation between force and displacement of each mount in its LCS is usually nonlinear and is simplified as piecewise linear in five ranges in this paper. An equation for estimating displacements of the powertrain center of gravity(C.G.) under static or quasi-static load is developed using Newton's second law, and an iterative algorithm is presented to calculate the displacements. Also an equation for analyzing the dynamic response of the powertrain under ground and engine shake excitations is derived using Newton's second law. Formulae for calculating reaction forces and displacements at each mount are presented. A generic PMS with four rubber mounts or two rubber mounts and two HEMs are used to validate the dynamic analysis and design calculation methods. Calculated displacements of the powertrain C.G. under static or quasi-static loads show that a powertrain motion can meet the displacement limits by properly selecting the stiffness and coordinates of the tuning points of each mount in its LCS using the calculation methods developed in this paper. Simulation results of the dynamic responses of a powertrain C.G. and the reaction forces at mounts demonstrate that resonance peaks can be reduced effectively with HEMs designed on the basis of the proposed methods.

• Journal of Biomedical Engineering Research
• /
• v.36 no.5
• /
• pp.169-176
• /
• 2015

Implantable closed-loop epilepsy controllers require ideally both accurate epileptic seizure detection and low power consumption. On-chip oscillators can be used in implantable devices because they consume less power than other oscillators such as crystal oscillators. In this study, we investigated the tolerable error range of a lower power on-chip oscillator without losing the accuracy of seizure detection. We used 24 ictal and 14 interictal intracranial electroencephalographic segments recorded from epilepsy surgery patients. The performance variations with respect to oscillator frequency errors were estimated in terms of specificity, modified sensitivity, and detection timing difference of seizure onset using Generic Osorio Frei Algorithm. The frequency errors of on-chip oscillators were set at ${\pm}10%$ as the worst case. Our results showed that an oscillator error of ${\pm}10%$ affected both specificity and modified sensitivity by less than 3%. In addition, seizure onsets were detected with errors earlier or later than without errors and the average detection timing difference varied within less than 0.5 s range. The results suggest that on-chip oscillators could be useful for low-power implantable devices without error compensation circuitry requiring significant additional power. These findings could help the design of closed-loop systems with a seizure detector and automated stimulators for intractable epilepsy patients.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.2
• /
• pp.194-202
• /
• 2003

In this paper, we introduce a category of Multi-FNN (Fuzzy-Neural Networks) models, analyze the underlying architectures and propose a comprehensive identification framework. The proposed Multi-FNNs dwell on a concept of fuzzy rule-based FNNs based on HCM clustering and evolutionary fuzzy granulation, and exploit linear inference being treated as a generic inference mechanism. By this nature, this FNN model is geared toward capturing relationships between information granules known as fuzzy sets. The form of the information granules themselves (in particular their distribution and a type of membership function) becomes an important design feature of the FNN model contributing to its structural as well as parametric optimization. The identification environment uses clustering techniques (Hard C - Means, HCM) and exploits genetic optimization as a vehicle of global optimization. The global optimization is augmented by more refined gradient-based learning mechanisms such as standard back-propagation. The HCM algorithm, whose role is to carry out preprocessing of the process data for system modeling, is utilized to determine the structure of Multi-FNNs. The detailed parameters of the Multi-FNN (such as apexes of membership functions, learning rates and momentum coefficients) are adjusted using genetic algorithms. An aggregate performance index with a weighting factor is proposed in order to achieve a sound balance between approximation and generalization (predictive) abilities of the model. To evaluate the performance of the proposed model, two numeric data sets are experimented with. One is the numerical data coming from a description of a certain nonlinear function and the other is NOx emission process data from a gas turbine power plant.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.9
• /
• pp.45-53
• /
• 2015

Adaptive support-weight based algorithm can produce better disparity map compared to generic area-based algorithms and also can be implemented as a realtime system. In this paper, we propose a realtime system based on geodesic support-weight which performs better segmentation of objects in the window. The data scheduling is analyzed for efficient hardware design and better performance and the parallel architecture for weight update which takes the longest delay is proposed. The exponential function is efficiently designed using a simple step function by careful error analysis. The proposed architecture is designed with verilogHDL and synthesized using Donbu Hitek 0.18um standard cell library. The proposed system shows 2.22% of error rate and can run up to 260Mhz (25fps) operation frequency with 182K gates.

• Earthquakes and Structures
• /
• v.19 no.5
• /
• pp.347-359
• /
• 2020

The Mega-Sub Controlled Structure System (MSCSS), an innovative vibration passive control system for building structures, is improved by adding lead rubber bearings (LRBs) on top of the substructure. For the new system, a genetic algorithm is used to optimize the dynamic parameters and distributions of dampers and LRBs. The program uses various seismic performance indicators as optimization objectives, and corresponding results are compared. It is found that the optimization procedure for maximizing the energy dissipation ratio yields the best solutions, and optimized models have consistent seismic performances under different earthquakes. Seismic performances of optimized MSCSS models with and without LRBs, as well as the traditional Mega-Sub Structure model, are evaluated and compared under El Centro wave, Taft wave and 20 other artificial waves. In both elastic and plastic analysis, the model with LRBs shows significantly smaller story drift and horizontal acceleration than those of the other two models, and fewer plastic hinges are developed during severe earthquakes. Energy analysis also shows that LRBs installed in proper locations increase the deformation and energy dissipation of dampers, thereby significantly reduce the kinetic, potential, and hysteretic energy in the structure. However, LRBs do not have to be mounted on all the additional columns. It is also demonstrated that LRBs at unfavorable locations can decrease the energy dissipation for dampers. After LRBs are installed, the optimal damping coefficient and the optimal damping exponent of dampers are reduced to produce the best damping effect.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.16 no.1
• /
• pp.36-46
• /
• 2013

The Geostationary Ocean Color Imager (GOCI), the first geostationary ocean color observation instrument launched in 2010 on board the Communication, Ocean, and Meteorological Satellite (COMS), has been generating the operational level 1 data. This study describes a methodology for creating the GOCI true color image and data processing software, namely the GOCI RGB maker. The algorithm uses a generic atmospheric correction and reprojection technique to produce the color composite image. Especially, the program is designed for educational purpose in a way that the region of interest and image size can be determined by the user. By distributing software to public, it would maximize the understanding and utilizing the GOCI data. Moreover, images produced from the geostationary observations are expected to be an excellent tool for monitoring environmental changes.

• Journal of Internet Computing and Services
• /
• v.5 no.1
• /
• pp.1-13
• /
• 2004

The effect of Application system with class units is not sufficient because of independency and reuse of Component elements due to component abstraction based on only source code. Therefore We need to apply design pattern approach to represent not only the problem abstraction but also information and relationship between system elements for generic solutions of specific domain, Also, it is essential to software reverse engineering acquiring the correct understandings of the system through examining the existing systems and utilizing the acquired knowledges as reusable resources. In this paper, the extraction algorithm with JAVA and the validity of applying reverse engineering with extracting design patterns from source codes of the existing object-oriented system; are devised. The architecture of automatic tool is designed and implemented for 1) automatic extraction of design patterns and 2) reuse tool for retrieving, editing and rebuilding of design patterns.

• Geophysics and Geophysical Exploration
• /
• v.12 no.1
• /
• pp.99-104
• /
• 2009

We propose a waveform inversion method for SH-wave data obtained in a shallow seismic refraction survey, to determine a 2D inhomogeneous S-wave profile of shallow soils. In this method, a 2.5D equation is used to simulate SH-wave propagation in 2D media. The equation is solved with the staggered grid finite-difference approximation to the 4th-order in space and 2nd-order in time, to compute a synthetic wave. The misfit, defined using differences between calculated and observed waveforms, is minimised with a hybrid heuristic search method. We parameterise a 2D subsurface structural model with blocks with different depth boundaries, and S-wave velocities in each block. Numerical experiments were conducted using synthetic SH-wave data with white noise for a model having a blind layer and irregular interfaces. We could reconstruct a structure including a blind layer with reasonable computation time from surface seismic refraction data.

• Journal of the Korea Society for Simulation
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2016

This study focuses on the air to air missile control fin planform optimization for the minimizing hinge moment with the considering phenomena of fluid and structure simultaneously. The fluid-structure interaction method is applied for the fluid and structure phenomena simulation of the control fins. A transient-loosely coupled method is used for the fluid-structure interaction simulation because it is suited for using each fluid and structure dedicated simulation software. Searching global optimization point is required many re-calculation therefore in this study, a mathematical model is applied for rapidly calculation. The face centered central composite method is used for generating design points and the 2nd polynomial response surface is sued for generating mathematical model. Global optimization is performed by using the generic algorithm. An objective function is the minimizing travel distance of the center of pressure between Mach 0.7 and 2.0 condition. Finally, the objective function of optimized planform is reduced 7.5% than the baseline planform with satisfying constrained conditions.