• 한국정밀공학회지
• /
• 제27권11호
• /
• pp.92-97
• /
• 2010

The object of this study is to investigate the definite method for pitting damaged surfaces. Pitting is a sort of fatigue damages and it is made by a repetitive load. For a judgment between damages or not, sensing vibrations of test equipment is simple. However, it is not only difficult to observe a growth of pitting but also impossible to detect the juncture of initial pitting. Therefore, a method for the pitting damaged area measuring technique was effectively implemented by Two Roller Machine. The change of surface damaged area was measured by an optical microscope in regular time and calculated by the use of dark and bright ratio of test specimens' pictures taken by optical microscope. In conclusion, S - N Curves gained by Failure rate - Cycle graph was led and the curves are able to be chosen as occasion demands for a failure area percentage.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1289-1290
• /
• 2010

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.95-101
• /
• 2012

An internal type roller ring gear(RRG) system composed of either a pin or a roller ring gear and its conjugated cam pinion can improve the gear endurance from that of a conventional gear system by reducing the sliding contact, while increasing the rolling motion. In this paper, we first proposed the exact cam gear profile and the self-intersection conditions obtained when the profile shift coefficient is introduced. Then, we investigated contact stresses and surface pitting life to fmd characteristics for surface fatigue by varying the shape design parameters. The results show that the pitting life can be extended significantly by increasing the profile shift coefficient.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1281-1282
• /
• 2010

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.99-104
• /
• 2012

This paper analyzes the pitting's cause of elevator's worm gear type traction machine. To find a cause of pitting problem, we analyzed vibration, a proper design allowance and lubrication. We brought a conclusion that the cause of pitting is not a simple vibration problem, such as misalignment of worm reducer and rail, but mostly related to a designed allowance. In this case, the allowance is tight. In general, the allowance of traction machine and lubrication is varied by manufacturers. When the allowance is tight, a proper lubrication can diminish the pitting problem.

• Tribology and Lubricants
• /
• 제27권1호
• /
• pp.40-44
• /
• 2011

The object of this study is to investigate influences of supplied lubricant quantities on spur gear's pitting life. Pitting is a sort of contact fatigue failures and made by a repetitive load. Basically, pitting is difficult to predict its life by an analysis due to many factors to be considered about tribology problems. In this paper, pitting life was proved by experiment using two roller machine. For a contact fatigue test, operating circumstances should be considered. During the test, temperature and lubricant quantities are considered and to investigate an influence of lubricant quantities, a comparison between optimally enough and not enough lubricant quantity was implemented.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1759-1766
• /
• 2001

Vibration transient generated by developing localized fault in gear can be used as indicators in gear fault detection. In this paper, we propose the zoomed phase map for a fault signal using continuous wavelet transfers to detect this vibration transient. Local fault induces the abrupt fluctuation of load exciting tooth and phase lag in the vibration signal measured on the gearbox. The relatively large fault like "tip breakage" easily can be detected by the clear fluctuation of exciting load. However, minor fault like "initial pitting"cannot be detected using the load fluctuation. To defect this kind of minor fault, the phase map for a fault signal is taken into account. The phase lag by minor fault is observed well in the zoomed phase map.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.38-42
• /
• 2009

Gear is an essential component of an automotive. Crowning is used for tooth modification of a gear. The basic concept of gear tooth crowning is to reduce the stress concentration in edge of contact area and appropriate profile modifications can help gears to resist scoring, pitting, and tooth breakage. In this study, a method to determinate spur gear tooth crowning amount to make smooth surface stress and subsurface stress distribution is proposed. This method is based on the contact analysis.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1453-1459
• /
• 2011

외접기어의 어느 한쪽 기어를 핀 또는 롤러로 대체한 롤러 피니언 기어 (RPG) 시스템은 기어 치물림 시 미끄럼 접촉을 줄이고 구름운동을 증대시켜 기어 내구성을 향상시킬 수 있다. 우선 본 논문에서는 전위계수(profile shift coefficient)를 고려하여 RPG 시스템의 캠 기어(cam gear)의 엄밀 치형설계 방법 및 치 꼬임으로 인한 간섭 방지조건을 제시하였다. 또 기어구동에 있어 치면에서 발생되는 진동이나 소음의 원인이 되는 피팅(pitting) 발생수명을 고려하기 위해, 설계인자의 변화에 따른 Hertz 접촉응력 및 하중응력계수(load stress factor)의 변화를 검토하였다. 이를 통해 RPG 시스템의 내구성을 향상시킬 수 있는 방안으로 전위계수의 증가를 제안하였다.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1231-1237
• /
• 1999

Applying the conjugate contact condition, contact lines of a cylindrical worm gear has been calculated. The characteristics of tooth contact were analyzed and the pitting resistance were also assessed. It has been verified that: i) the length of contact is shortest on the 1st tooth of the front region, ii) the contact region is more narrow in the recess side than in the access side, iii) the contact region is more narrow in worm than in worm wheel. Hence, the pitting resistance is weakest in the recess side of the 1st contacting worm tooth.