• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.158-165
• /
• 2008

The combustion and exhaust emissions characteristics of a liquefied petroleum gas-di-methyl ether compression ignition engine with a variable valve timing device were investigated under various liquefied petroleum gas injection timing conditions. Liquefied petroleum gas was used as the main fuel and was injected directly into the combustion chamber. Di-methyl ether was used as an ignition promoter and was injected into the intake port. Different liquefied petroleum gas injection timings were tested to verify the effects of the mixture homogeneity on the combustion and exhaust emission characteristics of the liquefied petroleum gas-di-methyl ether compression ignition engine. The average charge temperature was calculated to analyze the emission formation. The ringing intensity was used for analysis of knock characteristics. The combustion and exhaust emission characteristics differed significantly depending on the liquefied petroleum gas injection and intake valve open timings. The CO emission increased as the intake valve open and liquefied petroleum gas injection timings were retarded. However, the particulate matter emission decreased and the nitrogen oxide emission increased as the intake valve open timing was retarded in the diffusion combustion regime. Finally, the combustion efficiency decreased as the intake valve open and liquefied petroleum gas injection timings were retarded.

• 설비공학논문집
• /
• 제29권6호
• /
• pp.297-305
• /
• 2017

Air-source heat pumps are widely used in residential heating systems. However, the decrease in the capacity of the heat pump is unavoidable when operating at very low and high ambient temperatures. The vapor injection technique is considered a promising technology to overcome this problem. Recent research on vapor injection cycles have mainly adopted a scroll compressor with an internal heat exchanger at severe operating conditions. This study measured the COP and EER of a gas injection heat pump using a flash tank with an inverter-driven rotary compressor at severe operating conditions. Compared to non-injection heat pumps, the heating capacity and COP of the gas injection heat pump improved up to 15% and 2.9%, respectively, at outdoor temperatures of $-10^{\circ}C$ to $7^{\circ}C$. The cooling capacity of the gas injection heat pump was 11% higher than the non-injection heat pump at an outdoor temperature of $35^{\circ}C$. At the same time, the EER of the gas injection heat pump was similar to that of the non-injection heat pump.

• 한국산학기술학회논문지
• /
• 제16권11호
• /
• pp.7729-7735
• /
• 2015

플라스틱 사출성형제품은 금형을 제작하여 대량생산에 적합한 시스템으로서 두께가 두꺼운 자동차 핸들제품은 가스사출성형을 수행하는 것이 바람직하다. 가스사출성형은 용융된 원재료를 금형내로 충전시킨 후 질소가스를 주입하는 기술이다. 가스사출성형은 재료비절감, 품질향상 등 많은 장점을 가지고 있다. Moldflow소프트웨어를 활용하여 사출성형 공정을 해석하여 제품의 휨 변형을 최소하기 위한 게이트의 위치를 결정하였으며, 기존의 일반적인 PP재료로 가스사출 성형을 했을 경우 변형이 크게 발생되므로 미네랄이18% 함유된 PP 재료로 변경하여 사출제품의 휨 변형을 최소로 하는 것과 게이트의 위치를 변경하여 핑거링현상이 발생하는 트러블을 제거하는 것을 목적으로 하였다, 또한 가스 사출성형을 수행하였을 경우 원재료가 유입되고 난후 게이트를 기준으로 가스가 유입된 형상을 파악하기 위해 비교분석해 보았다. 본 연구를 통해 제품형상에 따른 두께의 변화와 가스사출성형을 수행하더라도 플라스틱의 재료에 따라 제품의 휨이 발생 될 수 있다는 것과 게이트의 위치가 제품의 트러블에 영향을 미친다는 것을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.43-50
• /
• 2002

In the present study, reduction of harmful exhaust gas in a diesel engine using stratified injection system of dual fuel (diesel fuel and methanol) was tried. The nozzle and fuel injection pump of conventional injection system were remodeled to inject dual fuel in order from the same injector. The quantity of each fuel was controlled by micrometers, which were mounted at rack of injection pumps. The injection ratio of dual fuel was certificated by volumetric ratio in injection quantity test. Cylinder pressure and exhaust gas were measured and analyzed under various supply condition of duel fuel. We confirmed that combustion of dual fuel was performed successful1y by using modified injection system in a D.I. diesel. Soot and NOx are simultaneously reduced by stratified injection without large deterioration of thermal efficiency, but THC and CO are relatively increased.

• 한국분무공학회지
• /
• 제27권4호
• /
• pp.181-187
• /
• 2022

For carbon neutrality, direct-injection hydrogen engines are attracting attention as a future power source. It is essential to estimate the transient injection rate of hydrogen for the optimization of hydrogen injection in direct injection engines. However, conventional injection rate measurement techniques for liquid fuels based on the injection-induced fuel pressure change in a test section are difficult to be applied to gaseous fuels due to the compressibility of the gas and the sealing issue of the components. In this study, a momentum flux measurement technique is introduced to obtain the transient injection rate of gaseous fuels using a force sensor. The injection rate calculation models associated with the momentum flux measurement technique are presented first. Then, the volumetric injection rates are estimated based on the momentum flux data and the calculation models and compared with those measured by a volumetric flow rate meter. The results showed that the momentum flux measurement can detect the injection start and end timings and the transient and steady regimes of the fuel injection. However, the estimated volumetric injection rates showed a large difference from the measured injection rates. An alternative method is suggested that corrects the estimated injection rate results based on the measured mean volumetric flow rates.

• 한국주조공학회지
• /
• 제21권1호
• /
• pp.33-40
• /
• 2001

Among the many techniques available to synthesis metal matrix composites, liquid phase processing, especially, conventional casting process such as stir-casting process is particularly attractive for their simplicity, economy and flexibility, In the present study, A356/20%SiCp composites were fabricated by gas-particle co-injection method. The gas-particle co-injection method is a modified stir-casting method and the corporation of particle could be improved by acceleration of particles due to rotation of impeller and gas purging. The microstructures and mechanical properties such as tensile properties and resistance to wear of fabricated materials were examined. Further, the particle injection mechanism in gas-particle co-injection method was discussed.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.19-24
• /
• 2004

Entrainment of ambient gas into a transient diesel spray is a crucial factor affecting the following preparation of combustible mixture. In this study, the entrainment characteristics of ambient gas for a non-evaporating transient diesel were investigated using a common-rail injection system. The effects of ambient gas density and nozzle hole geometry were assessed with entrainment coefficient. Laser Doppler Velocimetry (LDV) technique was introduced to measure the entrainment speed of ambient gas into a spray. There appeared a region where the entrainment coefficients remained almost constant while injection rates were still changing. The effect of common-rail pressure, which altered the slope of injection rate curve, was hardly noticed at this region. Entrainment coefficient increased with ambient gas density, that is, the effect of ambient gas density was greater than that of turbulent jet whose entrainment coefficient remained constant. The non-dimensional distance was defined to reflect the effect of nozzle hole diameter and ambient gas density together. The mean value of entrainment coefficient was found to increase with non-dimensional distance from the nozzle tip, which would be suggested as the guideline for the nozzle design.

• 한국유체기계학회 논문집
• /
• 제14권6호
• /
• pp.68-75
• /
• 2011

This study simulated the effect of steam injection on the performance and operation of a gas turbine combined heat and power (CHP) system. A commercial simple cycle gas turbine was analyzed. A full off-design analysis was carried out to investigate the variations in not only engine performance but also the operating characteristics of the compressor caused by steam injection. Variation in engine performance and operation characteristics according to various operation modes were examined. First, the impact of full steam injection was investigated. Then, operations aiming to guarantee a minimum compressor surge margin, such as under-firing and partial steam injection, were investigated. The former and latter were turned out to be relatively superior to each other in terms of power and efficiency, respectively.

• 소성∙가공
• /
• 제11권8호
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• 설비공학논문집
• /
• 제15권5호
• /
• pp.397-405
• /
• 2003

Heat and fluid flow in a compressor into which liquid refrigerant is injected for the purpose of reducing discharge gas temperature in a heat pump system has been numerically studied. A mechanistic approach encompassing liquid jet breakup and droplet evaporation has been performed to investigate the effects of liquid injection on the spacial and temporal variation of the gas temperature and pressure inside the compressor cylinder. Various parameters, such as liquid injection mass, time, duration and droplet size, are considered in the present study to elucidate the flow field inside the compressor. As the injection mass is increased, discharge gas temperature is decreased, while the pressure is increased due to the added mass of the injection. For the injected liquid mass corresponding to 15% of the total vapor mass in the cylinder, the discharge gas temperature drops by 22.4 K. It is observed that the droplet size plays a major role in the evaporation rate of the droplets that determines the degree of the discharge temperature drop.