• Tribology and Lubricants
• /
• 제28권1호
• /
• pp.33-37
• /
• 2012

Automotive wheel bearing grease helps to reduce stresses and prevent wear of wheel bearings. But it is easily contaminated by water and other contaminants. Previously, our research group reported the change of grease physical properties such as dropping point, work penetration and oxidation work stability, water washout characteristics, leakage tendency, oil separation, evaporation loss and rust protection by water contamination. In this paper, we analyzed the physical characteristics of grease such as lubricity, viscosity and total acid number to investigate the mechanism of thickener decomposition. In water contaminated grease, the total acid number and wear scar were increased, the viscosity was decreased due to the decomposition of lithium complex thickener.

• 대한기계학회논문집B
• /
• 제28권10호
• /
• pp.1155-1162
• /
• 2004

This paper is the forth paper of several companion papers which compare the method of Air-Fuel ratio determination. In the previous work, various AFR calculations were performed for various fuels and the results were compared with each other. The comparison, however, were limited to numerical value and estimation of each equation or method was insufficient. In this paper, the overall estimation of the methods was attempted. Also, the method of trouble shooting of instrumentation was presented. Through the estimation of methods, it is concluded that the Eltinge method contains inherently the most perfect thermal dissociation model as far as the exhaust composition is concerned; therefore, this might be regarded as the most general equation of AFR determination among the existing ones. The others might be considered as approximate form. In addition, the mal-distribution factor in Eltinge method is qualitatively equivalent to thermal dissociation chemical equilibrium constant K. Lastly, it is illustrated that all instrumentation error, including the sampling line leakage, can be easily detected through the analyzing the exhaust component on the Eltinge chart.

• 항공우주기술
• /
• 제9권2호
• /
• pp.8-13
• /
• 2010

축추력의 효과적인 제어는 터보펌프의 작동 안정성을 확보하는 데 중요한 기술 중 하나이다. 현재 개발 중인 75톤급 로켓엔진용 연료펌프에 대한 축추력 측정을 상온의 물을 매질로 하여 실시하였다. 시험 결과, 연료펌프의 축추력은 펌프 베어링의 축방향 하중 조건을 만족하는 것으로 예상되었다. 또한 연료펌프의 축추력은 대체로 유량이 작을수록 커졌다. 그리고 플로팅 링 실과 임펠러 사이의 간극이 바뀌었을 때, 연료펌프의 축방향 하중과 후방 누설 유량이 변화하는 것을 확인하였다.

• 조명전기설비학회논문지
• /
• 제27권7호
• /
• pp.67-75
• /
• 2013

In this paper, parallel input/serial output dual converter is designed appropriately for fuel cell hybrid power system. In case of proposed converter, zero voltage switching condition is designed without additional resonance device using leakage inductance of transformer and output capacitance of switch, and zero voltage switching method is used. Also, the system method is for increasing power by connecting half-bridge in parallel and increasing output voltage by connecting secondary output of transformer in serial. Through this method we can increase power and decrease volume of system. So in this paper, dual converter is designed. 1.5kW fuel cell hybrid power system was implemented, and system operation and stability was verified through experiment.

• 항공우주기술
• /
• 제3권2호
• /
• pp.183-190
• /
• 2004

액체로켓용 연료펌프의 설계를 검증하기 위해 상용 3차원 유동해석 소프트웨어를 이용하여 설계점 성능을 예측하였다. 연료펌프의 성능과 축추력에 영향을 미치는 누설유량에 대한 예측의 정확도를 높이기 위해 인듀서, 임펠러, 볼류트 및 2차 유로를 계산영역으로 설정하였으며 인듀서/임펠러/누설유로/볼류트 사이의 경계면에 혼합면 기법을 적용하여 계산에 소요되는 시간을 줄이고자 하였다. 유동해석을 통해 예측된 수력성능은 설계요구조건을 만족시키는 것으로 나타났으나 축추력이 허용치에 비해 크게 예측되어 이를 감소시키기 위한 설계변경이 이루어졌다. 변경된 설계안에 대한 유동해석을 수행한 결과 연료펌프의 수력성능은 유지되면서 축추력은 처음의 설계안에 비해 30% 수준으로 크게 감소하였음을 확인할 수 있었다.

• 대한기계학회논문집B
• /
• 제29권5호
• /
• pp.617-624
• /
• 2005

An analysis of the effects of $CO_{2}$ on fundamental combustion characteristics was performed in Oxygen enriched condition by comparing the laminar burning velocities, flame structures, fuel oxidation paths. Fictitious $CO_{2}$ was introduced to discriminate the chemical reaction effects of $CO_{2}$ from the thermal effects. PREMIX code was utilized to evaluate the laminar burning velocities. OPPDIF code was utilized to investigate the flame structure and fuel oxidation path variation. The contributions of thermal effects on laminar burning velocities are dominant at lowly oxygen-enriched condition but those of chemical reaction effects become dominant at highly oxygen-enriched condition. Chemical reaction effects caused the additional flame temperature decrease besides thermal effects and oxygen-leakage increase in non-premixed flame. Specific fuel oxidation path and CO production path is enhanced in spite of overall decrement of fuel consumption rate by chemical reaction effects of$CO_{2}$.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.149-156
• /
• 2006

Structure of edge flame established in a mixing layer, formed between two uniformly flowing pure $CH_4$ and pure $O_2$ streams, is numerically investigated by employing a detailed methane-oxidation mechanism. The numerical results exhibited the most outstanding distinction of using pure oxygen in the fuel-rich premixed-flame front, through which the carbon-containing compound is found to leak mainly in the form of CO instead of HC compounds, contrary to the rich $CH_4-air$ premixed flames in which $CH_4$ as well as $C_2H_m$ leakage can occur. Moreover, while passing through the rich premixed flame, a major route for CO production, in addition to the direct $CH_4$ decomposition, is found to be $C_2H_m$ compound formation followed by their decomposition into CO. Beyond the rich premixed flame front, CO is further oxidized into $CO_2$ in a broad diffusion-flame-like reaction zone located around moderately fuel-rich side of the stoichiometric mixture by the OH radical from the fuel-lean premixed-flame front. Since the secondary CO production through $C_2H_m$ decomposition has a relatively strong reaction intensity, an additional heat-release branch appears and the resulting heat-release profile can no longer be seen as a tribrachial structure.

• 한국연소학회지
• /
• 제11권1호
• /
• pp.19-26
• /
• 2006

Structure of edge flame established in a mixing layer, formed between two uniformly flowing pure $CH_4$ and pure $O_2$ streams, is numerically investigated by employing a detailed methane-oxidation mechanism. The numerical results exhibited the most outstanding distinction of using pure oxygen in the fuel-rich premixed-flame front, through which the carbon-containing compound is found to leak mainly in the form of CO instead of HC compounds, contrary to the rich $CH_4-air$ premixed flames in which $CH_4$ as well as $C_2H_m$ leakage can occur. Moreover, while passing through the rich premixed flame, a major route for CO production, in addition to the direct $CH_4$ decomposition, is found to be $C_2H_m$ compound formation followed by their decomposition into CO. Beyond the rich premixed flame front, CO is further oxidized into $CO_2$ in a broad diffusion-flame-like reaction zone located around moderately fuel-rich side of the stoichiometric mixture by the OH radical from the fuel-lean premixed-flame front. Since the secondary CO production through $C_2H_m$ decomposition has a relatively strong reaction intensity, an additional heat-release branch appears and the resulting heat-release profile can no longer be seen as a tribrachial structure.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.23-26
• /
• 2005

LOx와 Kerosene을 연료로 사용하는 LRE(Liquid Rocket Engine) Block에서 지상연소시험을 수행할 경우에 발생하는 위험도를 감소시키는 방법을 연구하였다. 추진제누출로 이어지는 위험한 상황에 대한 원인분석도와 추진제 유출시 사고로 이어지는 발전 양상 및 발전 프로세스, 사고시 손실을 줄이기 위한 기술적인 해결방법을 제시함으로써 기존의 확률적인 통계 값을 바탕으로 하는 것과는 또 다른 방법으로써 위험을 감소하기 위한 대안으로 사용하고자 한다.

• 대한안전경영과학회지
• /
• 제16권4호
• /
• pp.159-165
• /
• 2014

For the hydrogen economy system being tried starting with the 21st century, the fields that was not dealt with so far, such as the safety measure for large leakage accidents, the safety problem at infrastructures like a hydrogen station, the safety problem in terms of automobiles depending on introduction of hydrogen cars, the safety problem in a supply for homes like fuel cells, etc., are being deeply reviewed. In order to establish a safety control system, an essential prerequisite in using and commercializing hydrogen gas as an efficient energy source, it is necessary to conduct an analysis, such as analysis of hydrogen accident examples, clarification of physical mechanisms, qualitative and quantitative evaluation of safety, development of accident interception technologies, etc. This study prepared scenarios of hydrogen gas leakage that can happen at hydrogen stations, and predicted damage when hydrogen leaks by using PHAST for this.