• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1211-1214
• /
• 2003

The film is prepared by electron cyclotron resonance chemical vapor deposition (ECRCVD) employing CH$_4$ and H$_2$ gases. It is deposited by the control of microwave plasma power, gas flow ratio, deposition pressure, and In-situ thermal treatment temperature. The structure of a-C:H (hydrogenated amorphous carbon) thin film is analysed by FT-IR spectroscopy. The fraction sp$^3$ versus sp$^2$ bonding is very important to clear up the surface and interrace of a-C:H film properties such as nano-scale friction behavior. The sp$^3$ versus sp$^2$ bonding of a-C:H thin film is dependent on the deposition conditions, therefore. nano-scale friction behavior is dependent on the deposition conditions.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1585-1590
• /
• 2002

This paper reports on the balance weight effect on the lubrication and friction characteristics of crankshaft system. To determine the main bearing loads, the crankshaft was treated as statically determinate system. Four and eight-balance weight crankshafts were considered, and minimum oil film thickness and friction loss were calculated. The main bearing loads were increased in the four-balance shaft due to the increasing of unbalanced rotating mass at No. 1 and 3 main bearing sides. The minimum oil film thickness of four-balance shaft became thinner than eight-balance, and friction loss was increased.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.48-54
• /
• 1996

Examined in this paper, is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction materials. For the specimens 1wt%, 2wt% and 4wt% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to,measure the friction torque with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4wt% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.368-376
• /
• 2003

In this research, DLC thin films are produced as several hundred nm thickness by PE-CVD method. And then these thin films are estimated tribological characteristics to find out useful possibilities as a protecting film for high-quality function and life extension at MEMs by mechanical properties observation . These are measured thickness and residual stress of DLC coating. Compared after measuring friction coefficient, adhesion force, hardness, cohesive force of coating films. As results all test, we can decide several conclusions. First, friction coefficient decreased, as the load increased. otherwise, friction coefficient increased, as thickness of coating film increased under low load$(1\~50mN)$. Secod, adhesion force increased as thickness of coating films. Third, hardness of coating film is affected by substrate coating film when it is less than thickness of 300nm and it has general hardness of DLC coating film when it is more than thickness of 500nm. Fourth, cohesive force of coating film is complexly affected by hardness, adhesion force, residual stress, etc.

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.8-15
• /
• 2018

Films with special properties (e.g., water-repellent films, optical films, anti-reflection films, and flexible films) are referred to as functional films. Recently, there has been interest in fine patterning methods for film fabrication. In particular there have been many studies that use a UV nanoimprint process involving a UV curing method. In this paper, a polymer film was fabricated by the UV nanoimprint process with a micro-pattern, and its durability was evaluated by a wear test and a nano-indentation test. The film mechanical properties (such as coefficient of friction, hardness, and modulus of elasticity) were measured. Moreover, the choice of PUA type resin used in the UV nanoimprint process was confirmed to impact the durability of the thin film. Despite making the polymer film samples using the same method and PUA type resin, different coefficient of friction, hardness, and modulus of elasticity values were obtained. PUA 4 resin had the most favorable coefficient of friction, hardness, and modulus of elasticity. This material is predicted to produce a high durability functional film.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.772-779
• /
• 2000

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with a different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused a abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Tribology and Lubricants
• /
• 제24권1호
• /
• pp.21-26
• /
• 2008

A pin bush bearing is one of the most important element in the piston engine which is joined a piston to a connecting rod. A pin bush is suffered by heat and changeable repeat loads, which are come from the explosive gas heat and pressures during a reciprocating stroke. Therefore, a tribological behavior of pin bush bearings is very severe compared to other parts of a piston assembly. To keep a stable operation of pin bush bearings effectively, it would be satisfied with proper oil film strength for severe operating conditions and durability, which are strongly related to the oil film thickness, oil film pressure, and a friction loss power. The computed results show that the viscosity of engine oils slightly affects to the minimum oil film thickness and oil film pressure distribution, but is an influential parameter on a total friction loss power. Thus the low viscosity engine oils for an increased operation condition should select a high level of base oil and add a viscosity index improver as an oil film additive.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.363-367
• /
• 2009

Recently, the manufacturing of micro-cavity by means of laser surface texturing (LST) technique and low friction study by the LST have been in great progress. Most of current works have been dealing with the effect of cavity on friction and wear. The main objective of the present study was to investigate numerically two-dimensional lubrication characteristics of micro-dimple shapes fabricated on solid surfaces, and this study utilized the commercial CFD code (Fluent V.6.3). For the evaluation, preliminary simulation was conducted and numerical predictions were compared with the analytic solution obtained from the Reynolds's equation. Mainly, the present study investigated the influence of dimple depth, pattern shapes, and film thickness on lubrication characteristics related to the reduction of friction. It is found that the existence of micro-dimpled surface makes it possible to substantially reduce the friction forces exerted on the surfaces. In particular, substantial decrease in shear stresses was observed as the lubricant film thickness decreases. For instance, in the case of the film thickness of 0.01 mm, the estimated shear stress decreases up to about 40%. It indicates that the film thickness would be important factor in designing the micro-dimpled surfaces. Furthermore, it was observed that such a optimum dimple depth would be present because the dimple depth larger than the optimum value did no longer affect the reduction in shear stresses.

• KSTLE International Journal
• /
• 제10권1_2호
• /
• pp.43-47
• /
• 2009

Influences of carbonaceous ingredient as a solid lubricant in automotive friction materials on friction properties were studied. Three types of carbonaceous ingredients such as natural graphite, artificial graphite, and cokes were mixed using a constrained mixture design. A 1/5 scale brake dynamometer was used to obtain tribological properties. Results showed that cokes substantially increased the friction coefficient, and natural graphite effectively reduced stick-slip phenomena. This significant difference was attributed to the formation of the friction film on the brake pad which was shown to be strongly dependent on the graphite types. The different crystal structures of the carbonaceous solid lubricants played a significant role in the formation of friction film at the interface.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.28-31
• /
• 2001

Friction for sheet metal forming affects improvement of deep drawing formability. The deep drawing is affected by many process variables, such as lubricant, blank shapes, shape radius and so on. Especially, lubrication is very important formability factor. In this study, in order to investigate fraction coefficient of sheet metal forming, we examined friction test about three conditions, such as non-lubrication, full lubrication and film lubrication. We measured friction coefficient according to pin load under the conditions like deep drawing die. Mean friction coefficient for film lubrication condition would be very useful value to improve drawability.