• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.2
• /
• pp.107-111
• /
• 2014

An SIW cavity is a useful tool to design an FSS which shows a rapid roll-off rate and insensitivity to polarizations and incident angles of electromagnetic waves. However, due to its high Q-factor, the FSS also shows narrow bandwidth which is undesirable for high-capacity communication. To address this drawback, we propose a novel technique to enhance the bandwidth while maintaining similar frequency response characteristics and minimizing the increase of the overall thickness of the SIW cavity FSS. In order to verify the performance of the technique, simulated frequency responses will be provided. Also, a parameter which affects the bandwidth will be studied. Finally the stability to polarizations and incident angles will be observed through the simulated results.

• Composites Research
• /
• v.26 no.5
• /
• pp.279-288
• /
• 2013

In this paper, the delamination and deformed FSS caused by residual stresses in the Loop type FSS embedded composites and the transmission characteristic changes due to deformation of FSS by residual stresses were studied. FSS may have different electromagnetic characteristics depending on the type of element, design variables, and array. Therefore, design variables of square loop FSS embedded composites structures were determined to obtain the transmission characteristic for X-band (8~12 GHz). Then the design variables of other types of loops (triangular loop and circular loop) were determined based on the dimensions of square loop. Thereafter, the residual stresses and transmission characteristics of FSS embedded composite structures with various single and double loop FSS's, and stacking sequence of composite laminates were compared.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.4
• /
• pp.369-375
• /
• 2015

In this paper, transparent circuit analog radar absorbing structure with angular stability for stealth aircraft canopy was proposed and designed. To obtain wideband electromagnetic absorption, optical transparency and smaller thickness, we proposed the novel FSS(Frequency Selective Surface) for X-band and implemented the resistive FSS and PEC(Perfect Electric Conductor) plane using ITO(Indium Thin Oxide) coating with optical transmissivity of 90 %. Reflection loss characteristics for different incident angles of both TE(Transverse Electric) and TM(Transverse Magnetic) polarizations are presented through simulations. We then fabricated the proposed structure to verify the simulation results. The comparisons between the simulation and measured results show good agreements. The results also show that the proposed radar absorbing structure can provide better frequency stability for different incidence angles and polarizations as well as optical transparency. We can apply this proposed structure to the canopy of stealth aircraft and other stealth applications for visible transparency.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1501-1510
• /
• 2015

The frequency selective surface (FSS) embedded hybrid composite materials have been developed to provide excellent mechanical and specific electromagnetic properties. Radar absorbing structures (RASs) are an example material that provides both radar absorbing properties and structural characteristics. The absorbing efficiency of an RAS can be improved using selected materials having special absorptive properties and structural characteristics and can be in the form of multi-layers or have a certain stacking sequence. However, residual stresses occur in FSS embedded composite structures after co-curing due to a mismatch between the coefficients of thermal expansion of the FSS and the composite material. In this study, to develop an RAS, the thermal residual stresses of FSS embedded composite structures were analyzed using finite element analysis, considering the effect of stacking sequence of composite laminates with square loop (SL) and double square loop (DSL) FSS patterns. The FSS radar absorbing efficiency was measured in the K-band frequency range of 21.6 GHz. Residual stress leads to a change in the deformation of the FSS pattern. Using these results, the effect of transmission characteristics with respect to the deformation on FSS pattern was analyzed using an FSS Simulator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.791-799
• /
• 2016

This paper presents the design of reconfigurable frequency selective surfaces for X-band bandpass operation with improved isolation. The proposed reconfigurable FSS is composed of a four-legged loaded element, a inductive stub and a bias grid. The PIN diode is located between the four-legged loaded element and the stub, which can control the frequency response of reconfigurable FSS by ON/OFF state. By adjusting the length of the stub, the desired bandpass frequency and the improved isolation between ON and OFF state can be obtained. For validation of simulated results, we have carried out transmission characteristic measurements using rectangular waveguide of WR-90. The measured results are in good agreements with the simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.1
• /
• pp.1-9
• /
• 2018

In this paper, we propose a film-type dual-band frequency selective structure for improving the wireless communication environment in a building. The proposed frequency-selective structure is a miniaturized structure that can control the resonant frequencies of 2.4 GHz and 5 GHz dual band through simple design parameters. We fabricated the frequency-selective surface by screen printing using conductive ink on a thin transparent film and confirmed its performance by measurement. We analyzed the attenuation performance of the unnecessary signal from the outside when the frequency-selective structure designed using the software to analyze the propagation environment performance is applied to the building. To verify the analytical results, the signal strength of the indoor environment was measured by applying the frequency-selective film fabricated on the inner wall of the actual building. The measurement results show that the dual-band frequency-selective film has 29.4 dB and 15.94 dB attenuation performance in the 2.4 GHz and 5 GHz, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.12
• /
• pp.1223-1231
• /
• 2010

The design is presented for a SATCOM antenna capable of simultaneous multi-band (X/Ku/Ka-Band) communications without replacement of feed horns or change of other parts in the application as a ground satellite terminal for large data transfer. The antenna is the offset configuration and consists of a dual-band(X/Ka-band) feed horn, a single-band(Ku-band) feed horn, a frequency selective surface(FSS) sub-reflector and a parabolic main-reflector. The antenna has a main reflector defining a prime focus and a frequency selective surface sub-reflector defining an image focus. A dual-band feed and a single-band feed are provided at each of the prime focus and image focus. The antenna is designed using 3D EM simulator and the gains measured in X/Ku/Ka-band of the complete antenna assembly is more than 31.6dBi, 36.8dBi, 40.8dBi, and the cross polarization is 21.7dB, 26.6dB, 25.2dB, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.852-854
• /
• 2015

In this letter, we designed and fabricated the paper-based ring-type frequency selective surface(FSSs) using inkjet printing method for practicable building wall applications to enhancement of the indoor communication environment, including low cost and ease of fabrication. Designed FSS has the band-stop characteristics at X-band, stable angle of incidence and wide bandwidth. Comparisons between measured and simulated results showed the good agreements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.194-201
• /
• 2010

We propose a frequency selective surface(FSS) using double split ring resonators(DSRRs) for isolation enhancement between CDMA and RFID. The structure consists of an outer SRR and an inner SRR, and the gaps are formed in the same direction. By properly adjusting the gap and line width, the resonant frequency and skirt characteristics can be adjusted without varying the unit cell size. The proposed structure has a different field distribution from that of an ordinary SRR for magneto-dielectric materials. One layer consists of $9{\times}9$ unit cells and the other layer was separated by 50 mm. To validate the simulation results, we fabricated the patch antenna and the FSSs, and the measured results show a good agreement with the simulated ones. The electrical size of the unit cell is $0.110\;{\lambda}{\times}0.110\;{\lambda}{\times}0.002\;{\lambda}$, and the size of the two layer FSS is $1.058\;{\lambda}{\times}1.058\;{\lambda}{\times}0.153\;{\lambda}$. The two layer FSS maintain gain in CDMA frequency and has 6.9 dB reduced gain in RFID frequency.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.3
• /
• pp.75-81
• /
• 2012

In this paper, an efficient means to estimate the dispersion characteristics of active FSS (or ESS) is presented. We numerically investigate the effective permittivity and the transmission coefficient of 2D metal-fiber composites using linear-lumped impedance loading. We modify the GEC method which is applied to 2D fiber composite material with arbitrary fiber orientation. We show that by varying the impedance value it is possible to control the resonance frequency of the array as well as the bandwidth.