• Tunnel and Underground Space
• /
• v.19 no.4
• /
• pp.366-372
• /
• 2009

Recently, in order to achieve smooth fracture plane and minimize the excavation damage zone in rock blasting, controlled blasting methods which utilize new technologies such as electronic delay detonator (EDD) and a notched charge hole have been suggested. In this study, smooth blastings utilizing three wing type notched charge holes are simulated to investigate the influence of explosive initial density on the resultant fracture plane and damage zone using dynamic fracture process analysis (DFPA) code. Finally, based on the dynamic fracture process analyses, novel smooth blasting method, ED-Notch SB (Electronic Detonator Notched Charge Hole Smooth Blasting) is suggested.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.1 s.74
• /
• pp.51-58
• /
• 2007

This study on the effects of local wall-thinned location on the fracture behavior of pipes was carried out, and the results were compared with the analytical results. Local wall-thinning for the bending test was machined with various sizes on the outside of pipes, in order to simulate the metal loss, due to erosion/corrosion. In addition, we had carried out FE analysis for the pipes with local wall thinning on the inside, and its results were comparatively studied with that of the outside. Three-dimensional elasto-plastic analyses were able to accurately simulate fracture behaviors of inner or outer wall thinning. Fracture types, obtained from the experiments and analyses, could be classified into ovalization, local buckling and crack initiation, depending on the thinned length and thinned ratio. Based on the results, the fracture behaviors of pipes with the outer wall thinning can be applied to estimate the fracture behaviors of pipes with the inner wall thinning.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.153-163
• /
• 2000

The size effect on fracture toughness was investigated by introducing $J-A_2$ theory. For this application,small size specimens were chosen to establish $J-A_2$ assessment curve with FEM analysis. Two-dimensional FEM analysis was conducted with plane strain model using ABAQUS by domain integral method to calculate both crack tip stress and fracture toughness which were used to establish $J-A_2$ curve. The assessment curve predicted the fracture toughness of large specimens very well when compared to the test values. The results showed good prediction for deep crack specimen, though there were acceptable deviations in shallow cracked specimens, presumably caused by constraint effect. When the curve applied to reactor vessel in order to predict end of life fracture toughness with assumption of on-power pressure test condition, it provided the reasonable pressure compared to the existing design value. Better predictions would be possible if more test data were available.

• Coupled systems mechanics
• /
• v.6 no.1
• /
• pp.97-111
• /
• 2017

The present paper reports an analytical study of delamination fracture in the Mixed Mode Flexure (MMF) functionally graded beam with considering the material non-linearity. The mechanical behavior of MMF beam is modeled by using a non-linear stress-strain relation. It is assumed that the material is functionally graded along the beam height. Fracture behavior is analyzed by the J-integral approach. Non-linear analytical solution is derived of the J-integral for a delamination located arbitrary along the beam height. The J-integral solution derived is verified by analyzing the strain energy release rate with considering the non-linear material behavior. The effects of material gradient, crack location along the beam height and material non-linearity on the fracture are evaluated. It is found that the J-integral value decreases with increasing the upper crack arm thickness. Concerning the influence of material gradient on the non-linear fracture, the analysis reveals that the J-integral value decreases with increasing the ratio of modulus of elasticity in the lower and upper edge of the beam. It is found also that non-linear material behavior leads to increase of the J-integral value. The present study contributes for the understanding of fracture in functionally graded beams that exhibit material non-linearity.

• Transactions of Materials Processing
• /
• v.30 no.1
• /
• pp.16-21
• /
• 2021

A new concept of ammunition without the use of explosive gunpowder has been recently studied, which achieves performance equal to or higher than that of high explosives. Frangible Armor Piercing (FAP) is one of the concepts, which utilizes a tungsten alloy penetrator specialized for fragmentation. To investigate the fracture behavior of the tungsten alloy penetrator, Taylor impact tests were conducted at various impact velocities. Additionally, finite element analysis was performed to predict the fracture behavior of the tungsten alloy. Compression tests were also carried out at six strain rates for dynamic material properties and the dynamic hardening behavior was successfully predicted with the Lim-Huh model. Finally, the Mohr-Coulomb fracture model based on the mean stress was adopted to predict impact failure in Taylor impact simulation. The analysis predicts the deformation and fracture behaviors of the tungsten alloy successfully.

• Journal of KSNVE
• /
• v.11 no.3
• /
• pp.437-442
• /
• 2001

In this study, the fracture phenomena of optical disks are discussed by theoretical and experimental approaches and then some recommendations are presented to prevent the fracture. Linear equations of motion are discretized by using the Galerkin approximation. From the discretized equations, the dynamic responses are computed by the generalized- time integration method. As a fracture criterion for optical disks, the critical crack length is presented. From experimental methods, the fracture procedure is analyzed. The fracture occurs when disks have crack on the inner radius of the disks. Since the crack growth and the fracture result from the stress concentration on the tip of the crack, a measure should be taken to overcome the stress concentration. This problem can be resolved by the structural modification of a disk. This study proposes 3 types of improved optical disks.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.4
• /
• pp.178-184
• /
• 2013

The effects of thickness and surface grinding condition on the fracture strength of Si wafer with a thickness under $100{\mu}m$ were investigated. Fracture strength was measured by ball breaker test for about 330 dies (size: $4mm{\times}4mm$) per each wafer. For statistical analysis of the fracture strength, scale factor was determined from Weibull plot. Ball breaker fracture strength was observed to increase with decreasing thickness of silicon die. For the silicon dies of different surface conditions, ball breaker fracture strength was high in the order of polished, ground (#4800), and ground (#320 grit) specimen. Probabilistic fracture strength (i.e., scale factor) increased with decreasing surface roughness of silicon die.

• Steel and Composite Structures
• /
• v.23 no.3
• /
• pp.263-271
• /
• 2017

A theoretical study was carried-out of mode II delamination fracture behavior of the End Loaded Split (ELS) functionally graded beam configuration with considering the material non-linearity. The mechanical response of ELS was modeled analytically by using a power-law stress-strain relation. It was assumed that the material is functionally graded transversally to the beam. The non-linear fracture was investigated by using the J-integral approach. Equations were derived for the crack arm curvature and zero axes coordinate that are needed for the J-integral solution. The analysis developed is valid for a delamination crack located arbitrary along the beam height. The J-integral solution was verified by analyzing the strain energy release rate with considering material non-linearity. The effects of material gradient, non-linear material behavior and crack location on the fracture were evaluated. The solution derived is suitable for parametric analyses of non-linear fracture. The results obtained can be used for optimization of functionally graded beams with respect to their mode II fracture performance. Also, such simplified analytical models contribute for the understanding of delamination fracture in functionally graded beams exhibiting material non-linearity.

• Journal of Welding and Joining
• /
• v.21 no.6
• /
• pp.55-63
• /
• 2003

Welded joint generally has heterogeneity of strength, material, and fracture toughness and it is important to understand the characteristics of material strength and fracture of welded joint considering heterogeneous effect. Characteristics of strength and fracture of an undermatched joint under dynamic loading was studied by round-bar tension tests and thermal elastic-plastic analyses in this paper. The strength and fracture of the undermatched joints should be evaluated based on the effects of the strain rate and the temperature including temperature rise during the dynamic loading. The differences of fracture characteristics like such as ductile-to-brittle transition behavior are well precisely explained from the stress-strain distribution obtained by numerical analysis.

• Journal of Trauma and Injury
• /
• v.25 no.4
• /
• pp.139-144
• /
• 2012

Purpose: Hypovolemic shock is the leading cause of death in multiple trauma patients with pelvic bone fracures. The purpose of this study was to develop a simple prediction method for injury severity and amount of hemorrhage via an analysis of the correlation between the site of pelvic bone fracture and the amount of transfusion and to verify the usefulness of the such a simple scoring system. Methods: We analyzed retrospectively the medical records and radiologic examination of 102 patients who had been diagnosed as having a pelvic bone fracture and who had visited the Emergency Department between January 2007 and December 2011. Fracture sites in the pelvis were confirmed and re-classified anatomically as pubis, ilium or sacrum. A multiple linear regression analysis was performed on the amount of transfusion, and a simplified scoring system was developed. The predictive value of the amount of transfusion for the scoring system as verified by using the receiver operating characteristics (ROC). The area under the curve of the ROC was compared with the injury severity score (ISS). Results: From among the 102 patients, 97 patients (M:F=68:29, mean $age=46.7{\pm}16.6years$) were enrolled for analysis. The average ISS of the patients was $16.2{\pm}7.9$, and the average amount of packed RBC transfusion for 24 hr was $3.9{\pm}4.6units$. The regression equation resulting from the multiple linear regression analysis was 'packed RBC units=1.40${\times}$(sacrum fracture)+1.72${\times}$(pubis fracture)+1.67${\times}$(ilium fracture)+0.36' and was found to be suitable (p=0.005). We simplified the regression equation to 'Pelvic Bleeding Score=sacrum+pubis+ilium.' Each fractured site was scored as 0(no fracture) point, 1(right or left) point, or 2(both) points. Sacrum had only 0 or 1 point. The score ranged from 0 to 5. The area under the curve (AUC) of the ROC was 0.718 (95% CI: 0.588-0.848, p=0.009). For an upper Pelvis Bleeding Score of 3 points, the sensitivity of the prediction for a massive transfusion was 71.4%, and the specificity was 69.9%. Conclusion: We developed a simplified scoring system for the anatomical fracture sites in the pelvis to predict the requirement for a transfusion (Pelvis Bleeding Score (PBS)). The PBS, compared with the ISS, is considered a useful predictor of the need for a transfusion during initial management.