• Elastomers and Composites
• /
• 제58권2호
• /
• pp.65-69
• /
• 2023

To reduce the weight of the engineering plastic Nylon 6 resin, two high-temperature foaming agents, p-toluenesulfonyl semicarbazide (PTSS) and 5-phenyltetrazole (5-PT) (0-10 phr), were added and foamed without other additives. We investigated the effects of the foaming agent type and content on the foam density (g/cm³) and percent weight reduction rate of the Nylon 6 foam, and 5-PT exhibited better foaming performance than PTSS. In the case of 5-PT, the weight reduction rate was above 36% when the blowing agent content was 1.5 phr or higher, indicating that 5-PT is an effective blowing agent for reducing the Nylon 6 foam weight. Additionally, we studied the effect of the nucleating agent Talc content (0-0.4 phr) on Nylon 6 foaming, and the nucleating agent Talc considerably reduced foaming.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.55-56
• /
• 2015

This study is corroborated as a fundamental resource to develop structural lightweight paste containing silica fume as a part of cement. Paste using foaming agent is generated much foam and decreased density of paste. This study is measured at 0.8% of foaming agent dosage but over 0.8% of foaming agent dosage raise density of paste because of interconnection with foam. Also, FEM analysis using SEM image is confirmed correspondence of between Elastic modulus of experiment and FEM analysis.

• 한국안전학회지
• /
• 제29권2호
• /
• pp.18-23
• /
• 2014

Foam extinguishing agent is widely used for extinguishing combustible liquid fires. Compared to other foam type extinguishing agents, protein foam has relatively low cost and low toxicity and produces stable foam blanket which is excellent in heat resistance and sealability, despite it has weak fluidity. Therefore the study investigated foaming characteristics followed by various factors affecting the fluidity of the protein foam extinguishing agent. The extinguishing characteristics differentiated by the changes in fluidity were also experimented. Foaming performance was compared by measuring the expansion ratio and the 25% drainage time. Moreover, the 25% drainage time and the extinguishing time was compared. The results showed that the 25% drainage time and the expansion ratio were increased as the pressure of nozzle and the concentration of hydrolyzed protein liquid enlarged. However the foaming and extinguishing performance were not improved when the condition exceeded certain level of pressure and concentration. The fastest fire extinguishing condition was the nozzle pressure 4bar with the 85wt.% of concentration of hydrolyzed protein liquid.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 추계 학술논문 발표대회
• /
• pp.27-30
• /
• 2007

Recently, use of light-weight panel is increasing in building. Styrofoam sandwich panel is inexpensive and it is excellent in insulation ability and constructability. But styrofoam of panel inside is low ignition point. Consequently, when panel is fired, it is occur in poisonous gas. On the other hand, light-weight foamed concrete is excellent in insulation ability, fire resistance due to inner pore. Properties of light-weight concrete is influenced by foaming agent type. Accordingly, this study investigate in insulation property of according to foaming agent type in order to using light-weight foamed concrete instead of styrofoam. As a results, Non-heating zone temperature of light-weight foamed concrete of using AP, FP are lower than light-weight foamed concrete of using AES. Light-weight foamed concrete of using AES, FP are satisfied with fire performance of two hours at foam ratio 50, 100. Light-weight foamed concrete of using AP is satisfied with fire performance of two hours at AP ratio 0.1, 0.15. Insulation property is better closed pore by made AP, FP than open pore by made AES.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.756-759
• /
• 2003

It is increasing the interest on the comfortable dwelling environment and the efforts to solve the problem of the floor impact noise in apartment houses have been realized, as a result numerous products have been made. The purpose of this study is to investigate the sound insulation performances according to foaming rate of floor impact noise insulators and flooring coverings in Mock-up Test Room. The test results of impact insulation performance for each floor impact noise insulators is that double structure of insulator is excel than one in low-middle frequency band and as foaming rate go up, the sound insulation performance is improved.

• 한국도로학회논문집
• /
• 제10권4호
• /
• pp.19-29
• /
• 2008

최근에 $135^{\circ}C^{\circ}C$ 이하의 온도에서 생산되는 중온형 아스팔트 혼합물의 새로운 생산 기술이 전세계적으로 개발되고 있다. 본 연구에서는 가열 아스팔트보다 낮은 온도에서 아스팔트를 효과적으로 골재에 분산시켜 코팅할 수 있는 폼드 아스팔트 기술을 이용하여 중온형 아스팔트 혼합물을 생산하였으며, 최근 개발된 새로운 Simple Performance Testing 장비를 이용하여 다양한 온도와 하중조건 하에서 중온형 폼드 아스팔트 혼합물의 공용성 특성을 평가하였다. 중온형 폼드 아스팔트 혼합물은 FG 64-22의 아스팔트를 거품상태로 만들어 중온으로 가열된 골재에 뿌려서 제조하였으며, 중온형 아스팔트 혼합물은 중온의 골재에 FG 64-22의 아스팔트를 액상 상태로 첨가하여 제조하였다. 중온형 폼드 아스팔트 혼합물은 중온형 아스팔트 혼합물보다 높은 동탄성계수와 Flow Number를 나타내었다. 따라서, $100^{\circ}C$로 가열된 골재를 사용하여 생산된 중온형 폼드 아스팔트 혼합물은 중온형 아스팔트 혼합물에 비하여 피로균열 및 소성변형 저항에 우수한 것으로 평가되었다.

• 대한본초학회지
• /
• 제33권5호
• /
• pp.67-72
• /
• 2018

Objectives : Natural extracts have been extensively studied to replace single agent drugs that cause a variety of side effects. However, studies of changes to the formulation of natural extracts has not been nearly proceed. We aimed to investigate whether pharmacological stability of hyeonggaeyeongyotang gagambang (HYT) is altered by formulation changes for foaming tablet. Methods : In this study, we performed freeze - drying of HYT, which is known to have antioxidant and anti - inflammatory properties, and then changed the formulation by foaming. Results : As a result, the foaming reaction appeared normally when HYT foamed tablets were put into water, and almost all of the substances were dissolved in the aqueous solution. In addition, we confirmed using high-performance liquid chromatograph that the geniposide used as an indicator material of HYT was stable in most of the formulations. It was confirmed that the change of HYT formulation did not affect the antioxidant efficacy by the 2,2'-azino-bis-3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, quantitative real-time PCR confirmed that the inhibitory effect of HYT on IL-$1{\beta}$ mRNA expression induced by lipopolysaccharides treatment in murine macrophage RAW 264.7 cells was similar in the solution of foaming tablet. Conclusions : These results suggest that the materials with various pharmacological effects can be stably maintained even when the formulation is changed by the foaming action of HYT. Our results are expected to provide important basic knowledge on formulation changes using various natural extracts.

• 한국건축시공학회지
• /
• 제16권1호
• /
• pp.35-43
• /
• 2016

콘크리트는 대표적인 불균질 재료이며 콘크리트의 역학적 특성은 다양한 요인들에 의해 영향을 받는다. 그 중 콘크리트 내부에 존재하는 공극은 콘크리트의 강도를 결정하는데 많은 영향을 주고 있기 때문에 공극의 분포 및 크기를 파악하는 연구는 매우 중요하며 그 방법으로 화상이미지를 이용한 연구가 대두되고 있다. 경량 기포 콘크리트는 현재 비구조용에 관한 연구만 진행되고 있기 때문에, 구조용으로 사용하기 위한 경량 기포 콘크리트의 역학적 특성을 평가하고 화상 이미지를 기반으로 FEM 해석을 이용한 검증에 관한 연구는 미비하다. 그러므로 기포제 혼입률에 따른 시멘트 페이스트를 제작하여 역학적 성능 평가를 실시하고 화상 이미지를 이용하여 FEM 해석을 실시하여 역학적 성능 비교 및 검증을 실시하였다. 본 연구에서 기포제 혼입률에 따른 공극 분포를 확인하기 위해 7수준으로 하였으며 추 후 구조용 경량 기포 콘크리트에 대한 연구를 진행하기 위해 물-결합재비를 20%로 하였다. 기포제 혼입률이 0.8%에서 단위 용적 질량이 최소가 되었으며 그 이상 혼입했을 시 기포 간의 상호 연결로 인한 깨짐 현상이 발생하여 단위 용적 질량이 증가하였다. 공극 분포에 따른 FEM 해석을 위해 화상분석기(HF-MA C01)를 이용하여 시멘트 페이스트 단면을 촬영하였고 이를 토대로 OOF(Object Oriented Finite elements)를 이용한 FEM 해석을 실시한 결과 실험 탄성계수와 해석 탄성계수가 일치하였다.

• International Journal of Concrete Structures and Materials
• /
• 제4권1호
• /
• pp.55-62
• /
• 2010

The performance evaluation of a sodium lauryl sulfate to qualify as a foaming agent is presented in this paper. When new surfactants are used a systematic study of production parameters on the foam characteristics needs to be undertaken unlike proprietary foaming agents and foam generator for which manufacturer has predefined the parameters. The relative influence of the foam parameters and optimization of factors were carried out through a systematic experiment design. The foam production parameters namely foam generation pressure and dilution ratio of foaming agents are observed to have significant effect on all foam characteristics with the exception of foam output rate on which only foam generation pressure has influence. The foam with good initial foam density need not necessarily be stable foam. The optimum levels of foam production parameters are determined for the surfactant Sodium lauryl sulfate which can be used to produce stable foam for foam concrete production.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.162-163
• /
• 2017

This study investigated the properties of lightweight foamed concrete by using synthetic foaming agent and artificial lightweight aggregate. The effects of artificial lightweight sizes on the compressive strength, density and pore structure of the concrete were investigated. The samples were assessed by MIP analysis and simultaneous SEM was used to study their pore distribution. This study showed the improvement of important properties of lightweight foamed concrete. Lower pore distribution and correspondingly higher compressive strength values were reached. This is for the purpose of providing basic data for the use of lightweight foamed concrete through improvement on the problem such as unstability, falling in fluidity and the strength of existed foaming agent.