• Journal of Environmental Impact Assessment
• /
• v.16 no.4
• /
• pp.251-265
• /
• 2007

In this study, the influence of the construction of a large sized building on the flow and level of groundwater in a metropolitan area was investigated with simulation model MODFLOW for a selected area located in Gangseo-gu, Seoul, where a large business center was scheduled to be built. It was simulated that the groundwater level in the study area was suddenly lowered by the construction of a large building and groundwater in the surrounding area fast flowed into the study area. And even after the construction finished, the falling down of groundwater level consistently continued in some degree. The flow state of groundwater appeared to be the same in both cases where a soil cement wall is applied and where it is not during the construction. But for the case of application of a soil cement wall as the amount of groundwater flowing into the study site became reduced, it was estimated that the time for underground watershed getting far away from the site was also reduced and the influence of a building construction on the surrounding groundwater became reduced. Thus, it is deemed necessary that recharging the spilled ground water and rainfall into the construction area to lessen the abrupt change in flow and level of ground water should be considered in design of construction of a large sized building in a metropolitan area.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.3
• /
• pp.309-317
• /
• 2016

Debris flows are rapidly flowing masses of water mixed with soil and gravel from landslides which are caused by typhoons or rainstorms. The combination of Korea’s mountain dominated topography (70%) and seasonal heavy rains and typhoons causes landslides and large-scale debris flows from June to August. These phenomena often cause property damage and casualties that amount up to 20% of total annual disaster fatalities. The key point to predicting debris flow is to understand its movement mechanism, erosion, and deposition. In order to achieve a more accurate estimation of debris flow path and damage, this study incorporates quantitative analysis of high resolution LiDAR DEM (GSD 10cm) to delineate geomorphic and topographic changes induced by Jinbu real scale debris flow test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.85-94
• /
• 2004

Experimental study on combustion characteristics of double swirl coaxial injectors has been conducted for the assessment of critical injector design parameters. A reusable, unielement thrust chamber has been fabricated with a water-cooled copper nozzle. Two principal design parameters. a swirl angle and a recess length, have been investigated through hot firing tests for the understanding of their effects on high pressure combustion. Clearly, both parameters considerably affect the combustion efficiency, dynamics and hydraulic characteristics of an injector. Internal mixing of propellants in a recess region increases combustion efficiency along with the increase of a pressure drop required for flowing the same amount of mass flow rates. It is concluded that pressure buildup due to flame can be released by the increase of LOx flow axial momentum or the reduction of a recess length. Dynamic pressure measurements of the thrust chamber show varied dynamic behaviors depending on injector configurations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6558-6564
• /
• 2013

As the average indicator for amount of water flowing in any cross section of a river, the mean discharge has been reported to be a very important factor for examining water circle constructions in a river basin, the design and construction of a hydraulic structure, and water front area use and management. The stage-discharge curve based on discharge and stage data measured in a normal season were basically derived. Using this derivation, the necessary discharge data was obtained. The values produced in this manner corresponded to the measured data in a uniform flow state well, but showed limited accuracy in a flood season (unsteady flow). In the present paper, the mean velocity in unsteady flow conditions, which exhibited loop form properties, was estimated using the new mean velocity formula derived from Chiu's 2-D velocity. The results of RMSE and Polar graph analyses showed that the proposed equation exhibited approximately nineteen times the accuracy compared to the Manning and Chezy equations.

• Journal of Astronomy and Space Sciences
• /
• v.29 no.3
• /
• pp.259-267
• /
• 2012

Polar cap potential has long been considered as an indicator for the amount of energy flowing in the magnetosphere-ionosphere system. Thus, the estimation of polar cap potential is important to understand the physical process of the magnetosphere. To estimate the polar cap potential in the Northern Hemisphere, merging electric field by Kan & Lee (1979) is adopted. Relationships between the PC index and calculated merging electric field ($E^*$) are examined during full-time and storm-time periods separately. For this purpose Dst, AL, and PC indices and solar wind data are utilized during the period from 1996-2003. From this linear relationship, polar cap potential (${\Phi}^*$) is estimated using the formula by Doyle & Burke (1983). The values are represented as $58.1{\pm}26.9$ kV for the full-time period and $123.7{\pm}84.1$ kV for a storm-time period separately. Considering that the average value of polar cap potential of Doyle & Burke (1983) is about 47 kV during moderately quiet intervals with the S3-2 measurements, these results are similar to such. The monthly averaged variation of Dst, AL, and PC indices are then compared. The Dst and AL indices show distinct characteristics with peaks during equinoctial season whereas the average PC index according to the month shows higher values in autumn than in spring. The monthly variations of the linear correlation coefficients between solar wind parameters and geomagnetic indices are also examined. The PC-AL linear correlation coefficient is highest, being 0.82 with peaks during the equinoctial season. As with the AL index, the PC index may also prove useful for predicting the intensity of an auroral substorm. Generally, the linear correlation coefficients are shown low in summer due to conductance differences and other factors. To assess the role of the PC index during the recovery phase of a storm, the relation between the cumulative PC index and the duration is examined. Although the correlation coefficient lowers with the storm size, it is clear that the average correlation coefficient is high. There is a tendency that duration of the recovery phase is longer as the PC index increases.

• Corrosion Science and Technology
• /
• v.14 no.6
• /
• pp.261-266
• /
• 2015

The capacity of passive metal to repassivate after film damage determines the development of local corrosion and the resistance to corrosion failures. In this work, the repassivation kinetics of 316L stainless steel (316L SS) was investigated in borate buffer solution (pH 9.1) using a novel abrading electrode technique. The repassivation kinetics was analyzed in terms of the current density flowing from freshly bare 316L SS surface as measured by a potentiostatic method. During the early phase of decay (t < 2 s), according to the Avrami kinetics-based film growth model, the transient current was separated into anodic dissolution ($i_{diss}$) and film formation ($i_{film}$) components and analyzed individually. The film reformation rate and thickness were compared according to applied potential. Anodic dissolution initially dominated the repassivation for a short time, and the amount of dissolution increased with increasing applied potential in the passive region. Film growth at higher potentials occurred more rapidly compared to at lower potentials. Increasing the applied potential from 0 $V_{SCE}$ to 0.8 $V_{SCE}$ resulted in a thicker passive film (0.12 to 0.52 nm). If the oxide monolayer covered the entire bare surface (${\theta}=1$), the electric field strength through the thin passive film reached $1.6{\times}10^7V/cm$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.10
• /
• pp.718-725
• /
• 2007

In the general vapor-compression refrigeration system, refrigeration lubricant circulates in refrigeration system with refrigerant. Knowledge of the amount of circulating lubricant is very important to exactly calculate capacity of the refrigeration system. An experimental study was conducted to estimate the oil concentration of a flowing $CO_2/Oil$ mixtures. POE and PAG oil are considered as test lubricants in this study. Performance tests were conducted under simulated liquid conditions for $CO_2/POE$ oil mixture in oil concentration of 0 to 10 weight-percent and $CO_2/PAG$ oil mixture in oil concentration of 0 to 6 weight-percent in the temperature ranges of $-5^{\circ}C\;to\;15^{\circ}C$. The results obtained indicate specific gravity of $CO_2/Oil$ mixture is increased as oil concentration is increased and as temperature of mixture is decreased. Oil concentration correlation of $CO_2/POE$ oil mixture and $CO_2/PAG$ oil mixture is suggested, based on the measurement of specific gravity and temperature. This correlation enable to predict the oil concentration without extraction of the mixture and can be applied for $CO_2/POE$ mixtures and $CO_2/PAG$ mixtures.

• Journal of Korea Foundry Society
• /
• v.26 no.5
• /
• pp.222-226
• /
• 2006

Steel making slag has gained a considerable attraction as one candidate of eco-materials in research fields for recycling resources. Thus, many researches have been performed but were limited to development of substitute for cement being used in the construction field. A little research work also has been done on development of higher value-added materials, including heat resistant and sound absorbing materials. For this reason, the present study were focused on macrostructure characterization of fabricated slag fibers which are applicable to heat resistant materials. The slag fibers were fabricated through a modified melt extraction method. The processing variables employed were the wheel speed and molten slag temperature. The synthesized fibers were characterized by optical microscope and scanning electron microscopy. It was found that the wheel speed of 1400 rpm generated better quality of mineral fibers in terms of the relative amount of shot, diameter and length. This was attributed to the relative extent of contact width between the flowing melt and the rotating wheel. The thickness of the slag fibers also were decreased with increasing the slag melt temperature due mainly to significant decrease in the viscosity of the slag melt. In addition, the lower melt temperature caused an increase in number of shots plus the mineral fibers.

• Journal of Korean Society for Geospatial Information Science
• /
• v.14 no.4 s.38
• /
• pp.53-60
• /
• 2006

The purpose of this paper is forcasting of flooding area using LiDAR surveying data, and flood map for damage prevention is established for this purpose. Teahwa river at Ulsan city was chosen as test area and the flood simulation was produced in this area. For the flood simulation, each DEM using LiDAR data and digital map was established and then HEC model program and MIKE program was used to decide the amount of flood flowing and flood height. To improve the rainfall-overflow simulation confidence using inspection comparison of LiDAR data this paper analyzed and compared the LiDAR DEM accuracy and 1/5000 digital map DEM. The height accuracy is important factor to make flood map, however, LiDAR survey execution of all river area is not economic so, LiDAR survey execution of only important area is possible to be make high accuracy and economic flood map. The expectation effect of flood simulation is flood damage prevention and economic savings of recovery cost by forcasting of rainfall-overflow area and establishment of counter-measure.

• The Journal of Engineering Geology
• /
• v.12 no.3
• /
• pp.257-271
• /
• 2002

The vertical distribution of hydraulic conductivity of 3 boreholes located at Kongju National University was estimated by the ambient flow and the pump-induced flow measurements using a heat-pulse flowmeter. The ambient flow measurements showed that a great amount of groundwater (1~2 m$^3$/day) flowed in the boreholes through the conductive fractures. The analyzed conductivity profiles we similar to those of the packer test performed for the same boreholes. The conductive fractures in which the differential net flow changed greatly could be identified by the BIPS logging. The water-quality logging data showed that quality of groundwater changed abruptly at some depths of the boreholes. This change in water quality can be attributed to the presence of conductive fractures that have resulted in the mixing of groundwater of different quality flowing in different fracture channels. However, compared to the flowmeter test, the water-quality logging showed low capability in identifying locations of conductive fractures.