• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.113-118
• /
• 2007

The flow forming has been used to produce long thin walled tube parts, with the reduced fanning force and the enhanced mechanical and surface quality for a good finished part, compared with the fanned parts using other method. Therefore, flow fanning technique is used widely in industrial production. Spinning and flow fanning techniques are used frequently in automotive, aerial and defense industries. The main factors for the flow fanning machine design are motor power, bed rigidity, mandrel stiffness, spindle power, roller profile, etc. Especially, mandrel, spindle power and roller are important factors for flow fanning machine capacity. In this paper, three dimensional finite element method for analysis of one-roller backward flow fanning of a workpiece has been carried out to study effects of roller profile on fanning force. Applied roller profile have roller lead geometries of angle $20^{\circ},\;30^{\circ},\;40^{\circ}$, concave and convex. Axial and radial fanning forces on various roller profiles are obtained and compared with each analysis cases.

• Tribology and Lubricants
• /
• 제6권1호
• /
• pp.57-67
• /
• 1990

For increasing the performance of Machine tools, the improvement of the static and dynamic characteristics of spindle bearing is important. In this paper are the static characteristics, the pressure distribution, friction force and outlet flow rate, and the dynamic characteristics stiffness and damping coefficient, of a cylindrical hydrostatic journal bearing with multi oil pockets are analyzed.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.830-837
• /
• 2004

In this paper, the flow properties of staggered labyrinth seals are investigated. Leakage flowrates and pressure distributions are calculated for this seal. Then the dynamic stiffness and damping coefficients are calculated. The results are compared to the results of the some other papers.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1840-1850
• /
• 1994

Enhancement of numerical algorithms for low speed compressible flow will be considered. Contemporary time-marching algorithm has been widely accepted and applied as the method of choice for transonic, supersonic and hypersonic flows. In the low Mach number regime, time-marching algorithms do not fare as well. When the velocity is small, eigenvalues of the system of compressible equations differ widely so that the system becomes very stiff and the convergence becomes very slow. This characteristic can lead to difficulties in computations of many practical engineering problems. In the present approach, the time-derivative preconditioning method will be used to control the eigenvalue stiffness and to extend computational capabilities over a wide range of flow conditions (from very low Mach number to supersonic flow). Computational capabilities of the above algorithm will be demonstrated through computation of a variety of practical engineering problems.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 춘계 학술대회논문집
• /
• pp.35-42
• /
• 1998

Time marching algorithms applied to compressible Navier-Stokes equation have a convergence problem at low Mach number. It is mainly due to the eigenvalue stiffness and pressure singularity as Mach number approaches to zero. Among the several methods to overcome the shortcomings of time marching scheme, time derivative preconditioning method have been used successfully. In this numerical analysis, we adopted a preconditioner of K.H. Chen and developed a two-dimensional, axisymmetric Navier-Stokes program. The steady state driven cavity flow and backward facing step flow problems were computed to confirm the accuracy and the robustness of preconditioned algorithm for low Mach number flows. And the transonic and supersonic flows insice the JPL axisymmetric nozzle internal flow is exampled to investigate the effects of preconditioning at high Mach number flow regime. Test results showed excellent agreement with the experimental data.

• 한국자동차공학회논문집
• /
• 제25권2호
• /
• pp.201-206
• /
• 2017

In the study, the inner flow characteristics were analyzed by modifying the inner design parameter of the vane-type vacuum pump. The effect of pressure generated by the inner flow of pump on the rotor and vane was analyzed. The design parameter was analyzed using the angle variation of tilting and rotation of the vane. MRF was used for the analysis conducted using a virtual condition where the rotor and vane are rotated. The pressure gained from the load of the rotor and vane in the flow analysis is used for the structure analysis. Based on the results, the effect of variable vane design was revealed in structural strength. The effect of centrifugal and friction force generated during pump operation on structural strength was also analyzed.

• 한국유체기계학회 논문집
• /
• 제18권1호
• /
• pp.44-50
• /
• 2015

Labyrinth seals are commonly used in various kinds of turbomachinery to reduce leakage flow. In the present 3D CFD analysis of see-through-type labyrinth air seal, the methodology of determining leakage and rotordynamic coefficients is suggested with the relative coordinate system for steady-state simulation. The leakage flow and rotordynamic forces predicted by using different solvers and turbulent models of FLUENT are compared with the results of the existing bulk-flow analysis code LABYSEAL.FOR and experiment. The present CFD result of direct stiffness(K) shows only improvement in prediction. The results of leakage and rotordynamic coefficients as well as computing time are sensitive against the used solver and turbulent model.

• Nuclear Engineering and Technology
• /
• 제56권4호
• /
• pp.1407-1424
• /
• 2024

In Pressurized Water Reactors, most of the failed fuel rods are often observed at the periphery of the fuel assembly, especially near the core baffle. The rod vibration-induced fretting wear is a significant failure mechanism strongly correlated with the coolant and support conditions. This paper presents a coupled vibration model of double-rod to predict the grid-to-rod fretting (GTRF) wear. A motion-dependent fluid force model is used to simulate the coolant cross flow, the gap constraints with asymmetric stiffness between spring and dimple on the vibration form, and the fretting wear are discussed. The results show the effect of the coupled vibration on the deterioration of wear, providing a sound theoretical explanation of some failure phenomena observed in the previous experiment. Exploratively, we analyze the impact of the baffle jet on the GTRF wear, which indicates that the high-velocity cross-flow will significantly affect the vibration forms while sharply changing the wear behavior.

• 대한기계학회논문집A
• /
• 제20권1호
• /
• pp.79-87
• /
• 1996

SMC(Sheet Molding Compound) is made of unsaturated polyester resin and other additives reinforced with randomly distributed chopped fiberglass strands. Because of its higher stiffness per unit mass, SMC was used as a substitute for steel for automotive steel outer panels. Thus, understanding of flow characteristics during fabrication of SMC is of importance since the formation of weld line depends on material flow. In the present study, SMC compression molding simulations in the flat and T-shape molds were accomplished. During simulations, the preferential the preferential flow occurred at the low mold closing speed while plug flow was observed for the higher mold closing speed. When the preferential flow was observed, the weld line was seen at the final stage. For simulations, rigid-viscoplastic finite element method was applied. Self-contact algorithm was also applied in order to predict the formation of the weld line. Simulation results were compared to the experimental results available in the literature.

• Elastomers and Composites
• /
• 제50권3호
• /
• pp.184-188
• /
• 2015

There is a need for light weight and high stiffness characteristics in the building structure as well as aircraft and cars. So fiber reinforced plastic with the addition of reinforcing agent such as glass fiber, carbon fiber, aramid fiber is utilized in this regard. In this study, mechanical strength, flow property and part shrinkage of glass fiber and carbon fiber reinforced PA6 were examined according to reinforcement content such as 10%, 20%, and 30%, and reinforcement type. The mechanical property was measured by a tensile test with specimen fabricated by injection molding and the flow property was measured by spiral test. In addition, we measured the part shrinkage of fiber reinforced PA6 that affects part quality. As glass fiber content increases, mechanical property increased by 75.4 to 182%, and flow property decreased by 18.9 to 39.5%. And part shrinkage decreased by 52.9 to 60.8% in the flow direction, and decreased by 48.2 to 58.1% in the perpendicular to the flow direction. As carbon fiber content increases, mechanical property increased by 180 to 276%, flow property decreased by 26.8 to 42.8%, and part shrinkage decreased by 65.0 to 71.8% and 69.5 to 72.7% in the flow direction and the direction perpendicular to the flow respectively.