• 콘크리트학회지
• /
• 제11권1호
• /
• pp.243-254
• /
• 1999

면외 바닥하중과 면내 압축력을 받는 플랫플레이트 슬래브에 적용할 수 있는 모멘트증대법을 개발하기 위하여 수치해석연구를 실시하였다. 수치해석연구를 위하여 재료와 기하학적 비선형효과를 고려한 비선형 유한요서 해석프로그램을 개발하였으며, 해석모델로서 국내 철근콘크리트계산규준의 직접설계법에 의하여 설계된 플랫플레이트 슬래브를 사용하였다. 본 연구는 지배하중조건인 수직하중후 1축압축력의 조합하중을 받는 슬래브에 대한 좌굴하중과 모멘트증대계수를 제안하였다. 좌굴하중은 두 개의 요소, 즉 슬래브의 기하학적 형태의 영향을 나타내는 좌굴계수와 압축과 인장 균열에 의한 손상정도를 나타내는 유효휨강성으로 정의된다. 변수연구를 통하여 좌굴계수와 유효휨강성의 변화를 연구하였으며, 이 수치해석결과를 바탕으로 좌굴계수와 유효휨강성의 설계값과, 이를 사용하는 모멘트증대법을 제안하였다.

• 전산구조공학
• /
• 제9권4호
• /
• pp.135-140
• /
• 1996

박벽개단면을 갖는 단일 형강재는 압축재로 될 수 있는데 예를 들면 트러스에서 복재가 이런 경우이다. 이 때에는 부재의 조립 때문에 발생하는 필연적 편심을 구조설계시에는 보통 무시한다. 그러나 편심의 영향은 부재를 설계할 때, 특히 압축부재의 설계에서는 고려되어야 할 사항이다. 비틀림이나 혹은 휨과 비틀림에 의해서 좌굴을 일으키는 압축재의 임계하중은 지배하는 비분방정식의 해를 구함으로써 결정된다. 본 논문에서는 채널([), 등변앵글(L), 리프채널(C)의 편심변화에 따른 내하력을 도표로 나타내기로 한다. 또한 식이복잡하므로 컴퓨터를 이용하여 계산한 후, 그 결과를 SURFER프로그램을 사용하여 그래프로 표시하였다.

• Steel and Composite Structures
• /
• 제13권2호
• /
• pp.123-137
• /
• 2012

Steel plate-masonry composite structure is a newly-developed type of structural technique applicable to existing masonry buildings by which the load-bearing walls can be removed for large spaces. This kind of structure has been used in practice for its several advantages, but experimental investigation on its elements is nearly unavailable in existing literature. This paper presents an experimental study on the flexural behaviour of four steel plate-masonry composite beams loaded by four-point bending. Test results indicate that failure of the tested beams always starts from the local buckling of steel plate, and that the tested beams can satisfy the requirement of service limit state. In addition, the assumption of plane section is still remained for steel plate prior to local buckling or steel yielding. By comparative analyses, it was also verified that the working performance of the beam is influenced by the cross-section of steel plate, which can be efficiently enhanced by epoxy adhesive rather than cement mortar or nothing at all. Besides, it was also found that the contribution of the encased masonry to the flexural capacity of the composite beam cannot be ignored when the beam is injected with epoxy adhesive.

• Structural Engineering and Mechanics
• /
• 제23권4호
• /
• pp.369-386
• /
• 2006

The influence of reinforcement buckling on the flexural response of reinforced concrete members is studied. The stress-strain response of compression reinforcement is determined computationally using a large-strain finite element model for bars of varied diameter, length, and initial eccentricity, and a mathematical expression is fitted to the simulation results. This relationship is used to represent the response of bars in compression in a moment-curvature analysis of a reinforced concrete cross section. The compression bar may carry more or less force than a tension bar at a corresponding strain, depending on the relative influence of Poisson effects and bar slenderness. Several cross-section analyses indicate that, for the distances between stirrups prescribed in modern concrete codes, the influence of inelastic buckling of the longitudinal reinforcement on the monotonic moment capacity is very small and can be neglected in many circumstances.

• 한국방재학회 논문집
• /
• 제9권2호
• /
• pp.11-15
• /
• 2009

본 논문에서는 균일 모멘트 하중을 받는 박판 아치의 탄성 좌굴에 관한 연구를 수행하였다. 초기 곡률을 고려한 비선형 변형률-변위 관계식을 전체 포텐셜 에너지 방정식의 이차 변분에 대입하여 초기 곡률 효과를 포함하는 에너지 방정식을 유도하였다. 휨 모멘트에 의한 단면 내 법선 변형률이 선형으로 분포한다는 초기 곡률 효과에 대한 가정사항을 유도과정에 일관되게 적용하였다. 균일 모멘트 하중을 받는 아치의 휨-비틀림 좌굴하중에 관한 제차해를 제시하고 타 연구자의 결과와 비교하였다.

• Steel and Composite Structures
• /
• 제34권1호
• /
• pp.123-139
• /
• 2020

The tube outward local buckling of Concrete-Filled Steel Tube (CFST) beam under high compression stress is still considered a critical problem, especially for steel tubes with a slender section compared to semi-compact and compact sections. In this study, the flexural performance of stiffened slender cold-formed square tube beams filled with normal concrete was investigated. Fourteen (14) simply supported CFST specimens were tested under static bending loads, stiffened with different shapes and numbers of steel stiffeners that were provided at the inner sides of the tubes. Additional finite element (FE) CFST models were developed to further investigate the influence of using internal stiffeners with varied thickness. The results of tests and FE analyses indicated that the onset of local buckling, that occurs at the top half of the stiffened CFST beam's cross-section at mid-span was substantially restricted to a smaller region. Generally, it was also observed that, due to increased steel area provided by the stiffeners, the bending capacity, flexural stiffness and energy absorption index of the stiffened beams were significantly improved. The average bending capacity and the initial flexural stiffness of the stiffened specimens for the various shapes, single stiffener situations have increased of about 25% and 39%, respectively. These improvements went up to 45% and 60%, for the double stiffeners situations. Moreover, the bending capacity and the flexural stiffness values obtained from the experimental tests and FE analyses validated well with the values computed from equations of the existing standards.

• Structural Engineering and Mechanics
• /
• 제53권1호
• /
• pp.147-158
• /
• 2015

Elements used in steel structures may be considered as an assembly of number of thin flat walls. Local buckling of these members can limit the buckling capacity of axial load resistance or flexural strength. We can avoid a premature failure, caused by effects of local buckling, by limiting the value of the wall slenderness which depend on its critical buckling stress. According to Eurocode 3, the buckling stress is calculated for an internal wall assuming that the latter is a simply supported plate on its contour. This assumption considers, without further requirement, that the two orthogonal walls to this wall are sufficiently rigid to constitute fixed supports to it. In this paper, we focus on webs of steel profiles that are internal walls delimited by flanges profiles. The objective is to determine, for a given web, flanges dimensions from which the latter can be considered as simple support for this web.

• 대한토목학회논문집
• /
• 제11권4호
• /
• pp.27-35
• /
• 1991

본 연구는 직선변이 단순지지, 원호변이 단순지지 및 고정지지 조건을 갖는 원통 panel을 해석하는 방법을 제시하였고 진동 및 좌굴에 관한 특성을 규명한 것이다. 초기응력을 받는 원통 panel을 지배하는 미분방정식은 Love-Timoshenko의 기초식을 이용하여 유도하였으며 이 미분방정식을 Galerkin 해석법을 이용하여 수치해석 하였다. 특히 고정 지지조건을 갖는 panel에 대해서는 시행함수로서 삼각함수로 구성되는 경우와 쌍곡선함수로 된 보의 고유함수로 구성되는 경우에 대하여 각각 해석하였으며 이들 시행함수가 수치해에 미치는 영향을 검토하였다. 수치해석의 결과로 곡률 parameter와 고유 진동수 및 임계 좌굴계수와의 관계를 검토하였다. 또한 진동 및 좌굴 모드를 도시하였다.

• Structural Engineering and Mechanics
• /
• 제21권4호
• /
• pp.407-422
• /
• 2005

Plate elements in fully profiled sandwich panels are generally subjected to local buckling failure modes and this behaviour is treated in design by using the conventional effective width method for plates with a width to thickness (b/t) ratio less than 100. If the plate elements are very slender (b/t > 1000), the panel failure is governed by wrinkling instead of local buckling and the strength is determined by the flexural wrinkling formula. The plate elements in fully profiled sandwich panels do not fail by wrinkling as their b/t ratio is generally in the range of 100 to 600. For this plate slenderness region, it was found that the current effective width formula overestimates the strength of the fully profiled sandwich panels whereas the wrinkling formula underestimates it. Hence a new effective width design equation has been developed for practical plate slenderness values. However, no guidelines exist to identify the plate slenderness (b/t) limits defining the local buckling, wrinkling and the intermediate regions so that appropriate design rules can be used based on plate slenderness ratios. A research study was therefore conducted using experimental and numerical studies to investigate the effect of plate slenderness ratio on the ultimate strength behaviour of foam supported steel plate elements. This paper presents the details of the study and the results.

• Steel and Composite Structures
• /
• 제23권2호
• /
• pp.217-228
• /
• 2017

Braces are one of the retrofitting systems of structure under earthquake loading. Buckling restrained braces (BRBs) are one of the very efficient braces for lateral loads. One of the key needs for a desirable and acceptable behavior of buckling-restraining brace members under intensive loading is that it prevents total buckling until the bracing member tolerates enough plastic deformation and ductility. This paper presents the results of a set of analysis by finite element method on buckling restrained braces in which the filler materials within the restraining member have been removed. These braces contain core as the conventional BRBs, but they have a different buckling restrained system. The purpose of this analysis is conducting a parametric study on various empty spaces between core and restraining member, the effect of friction between core and restraining member and applying initial deformation to brace system to investigate the global buckling behavior of these braces. The results of analysis indicate that the flexural stiffness of restraining member, regardless of the amount of empty space, can influence the global buckling behavior of brace significantly.